Technical Data Sheet 0805 Package Chip LED(1.0mm Height) 17-21/S2C-AP1Q2B/3T Features ․Package in 8mm tape on 7〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Mono-color type. ․Pb-free. ․The product itself will remain within RoHS complaint version. Descriptions ․The 17-21 SMD LED is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. ․Besides, lightweight makes them ideal for miniature applications. etc. Applications ․Backlighting in dashboard and switch. ․Telecommunication: indicator and backlighting in telephone and fax. ․Flat backlight for LCD, switch and symbol. ․General use. Device Selection Guide Part No. 17-21/S2C-AP1Q2B/3T Everlight Electronics Co., Ltd. Device No: DSE-0002429 Chip Material AlGaInP Emitted Color Resin Color Brilliant Orange Water Clear http://www.everlight.com Prepared date: 20-Sep-2009 Rev. 2 Page: 1 of 10 Prepared by: Yang Peng 17-21/S2C-AP1Q2B/3T Package Outline Dimensions - 1.05 + Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. Device No: DSE-0002429 http://www.everlight.com Prepared date: 20-Sep-2009 Rev. 2 Page: 2 of 10 Prepared by: Yang Peng 17-21/S2C-AP1Q2B/3T Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Unit Reverse Voltage VR 5 V Forward Current IF 25 mA IFP 60 mA Power Dissipation Pd 60 mW Electrostatic Discharge(HBM) ESD 2000 V Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +90 ℃ Soldering Temperature Tsol Peak Forward Current (Duty 1/10 @1KHz) Reflow Soldering : 260 ℃ for 10 sec. Hand Soldering : 350 ℃ for 3 sec. ℃ Electro-Optical Characteristics (Ta=25℃) Parameter Symbol Min. Typ. Max. Unit Luminous Intensity IV 45.0 ----- 112 mcd Viewing Angle 2θ1/2 ----- 140 ----- deg Peak Wavelength λp ----- 611 ----- nm Dominant Wavelength Condition IF=20mA λd 600.5 ----- 612.5 nm Spectrum Radiation Bandwidth △λ ----- 17 ----- nm Forward Voltage VF 1.75 ----- 2.35 V Reverse Current IR ----- ----- 10 µA VR=5V Notes: 1.Tolerance of Luminous Intensity ±11% 2.Tolerance of Dominant Wavelength ±1nm 3.Tolerance of Forward Voltage ±0.1V Everlight Electronics Co., Ltd. Device No: DSE-0002429 http://www.everlight.com Prepared date: 20-Sep-2009 Rev. 2 Page: 3 of 10 Prepared by: Yang Peng 17-21/S2C-AP1Q2B/3T Bin Range Of Luminous Intensity Bin Min Max P1 45.0 57.0 P2 57.0 72.0 Q1 72.0 90.0 Q2 90.0 112 Unit Condition mcd IF=20mA Unit Condition Bin Range Of Dom. Wavelength Group A Bin Min Max D8 600.5 603.5 D9 603.5 606.5 D10 606.5 609.5 D11 609.5 612.5 nm IF=20mA Bin Range Of Forward Voltage Group Bin Min Max 0 1.75 1.95 1 1.95 2.15 2 2.15 2.35 B Unit V Condition IF=20mA Notes: 1.Tolerance of Luminous Intensity ±11% 2.Tolerance of Dominant Wavelength ±1nm 3.Tolerance of Forward Voltage ±0.1V Everlight Electronics Co., Ltd. Device No: DSE-0002429 http://www.everlight.com Prepared date: 20-Sep-2009 Rev. 2 Page: 4 of 10 Prepared by: Yang Peng 17-21/S2C-AP1Q2B/3T Typical Electro-Optical Characteristics Curves Everlight Electronics Co., Ltd. Device No: DSE-0002429 http://www.everlight.com Prepared date: 20-Sep-2009 Rev. 2 Page: 5 of 10 Prepared by: Yang Peng 17-21/S2C-AP1Q2B/3T Label explanation Pb CAT: Luminous Intensity Rank EVERLIGHT CPN : P N : XXXXXXXXXXXXX HUE: Dom. Wavelength Rank RoHS REF: Forward Voltage Rank XXXXXXXXXXXXX CAT : XXX HUE : XXX REF : XXX QTY : XXX LOT NO : XXXXXXXXXX Reference : XXXXXXXX MADE IN TAIWAN Reel Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. Device No: DSE-0002429 http://www.everlight.com Prepared date: 20-Sep-2009 Rev. 2 Page: 6 of 10 Prepared by: Yang Peng 17-21/S2C-AP1Q2B/3T Carrier Tape Dimensions: Loaded quantity 3000 PCS per reel Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Moisture Resistant Packaging Label Aluminum moisture-proof bag Everlight Electronics Co., Ltd. Device No: DSE-0002429 http://www.everlight.com Prepared date: 20-Sep-2009 Desiccant Rev. 2 Label Page: 7 of 10 Prepared by: Yang Peng 17-21/S2C-AP1Q2B/3T Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% No. Items 1 Reflow Soldering 2 Temperature Cycle 3 Thermal Shock 4 5 High Temperature Storage Low Temperature Storage Test Condition Temp. : 260℃±5℃ Min. 5sec. H : +100℃ 15min ∫ 5 min L : -40℃ 15min H : +100℃ 5min ∫ 10 sec L : -10℃ 5min Test Sample Hours/Cycles Size 6 Min. Ac/Re 22 PCS. 0/1 22 PCS. 0/1 300 Cycles 22 PCS. 0/1 Temp. : 100℃ 1000 Hrs. 22 PCS. 0/1 Temp. : -40℃ 1000 Hrs. 22 PCS. 0/1 300 Cycles 6 DC Operating Life IF = 20 mA 1000 Hrs. 22 PCS. 0/1 7 High Temperature / High Humidity 85℃/ 85%RH 1000 Hrs. 22 PCS. 0/1 Everlight Electronics Co., Ltd. Device No: DSE-0002429 http://www.everlight.com Prepared date: 20-Sep-2009 Rev. 2 Page: 8 of 10 Prepared by: Yang Peng 17-21/S2C-AP1Q2B/3T Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 After opening the package: The LED's floor life is 1 year under 30℃ or less and 60% RH or less. If unused LEDs remain, it should be stored in moisture proof packages. 2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. Device No: DSE-0002429 http://www.everlight.com Prepared date: 20-Sep-2009 Rev. 2 Page: 9 of 10 Prepared by: Yang Peng 17-21/S2C-AP1Q2B/3T 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Everlight Electronics Co., Ltd. Device No: DSE-0002429 Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com http://www.everlight.com Prepared date: 20-Sep-2009 Rev. 2 Page: 10 of 10 Prepared by: Yang Peng