EVERLIGHT ELECTRONICS CO.,LTD. Technical Data Sheet 0603 Package Chip LED (0.6 mm Height) 19-213/GHC-YR1S2/3T Features ․Package in 8mm tape on 7〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Mono-color type. ․Pb-free. Descriptions ․The 19-213 SMD Taping is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. ․Besides, lightweight makes them ideal for miniature applications. etc. Applications ․Automotive: backlighting in dashboard and switch. ․Telecommunication: indicator and backlighting in telephone and fax. ․Flat backlight for LCD, switch and symbol. ․General use. Device Selection Guide Part No. 19-213/GHC-YR1S2/3T Everlight Electronics Co., Ltd. Device No:SZDSE-193-G03 Chip Material Emitted Color InGaN Brilliant Green http://www.everlight.com Prepared date: 8-5-2004 Lens Color Water Clear Rev. 1 Page: 1 of 10 Prepared by: Aihua hong EVERLIGHT ELECTRONICS CO.,LTD. 19-213/GHC-YR1S2/3T Package Outline Dimensions - + Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. Device No:SZDSE-193-G03 http://www.everlight.com Prepared date: 8-5-2004 Rev. 1 Page: 2 of 10 Prepared by: Aihua hong EVERLIGHT ELECTRONICS CO.,LTD. 19-213/GHC-YR1S2/3T Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Unit Reverse Voltage VR 5 V Forward Current IF 25 mA Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +90 ℃ Soldering Temperature Tsol Electrostatic Discharge ESD 150 V Power Dissipation Pd 110 mW IFP 100 mA Peak Forward Current (Duty 1/10 @1KHz) 260 (for 5 second) ℃ Electro-Optical Characteristics (Ta=25℃) Parameter Symbol Min. Typ. Max. Unit Luminous Intensity Iv 112 ---- 285 mcd Viewing Angle 2θ1/2 λp 120 518 --------- deg Peak Wavelength --------- Dominant Wavelength λd 520 ----- 535 nm Spectrum Radiation Bandwidth △λ ----- 35 ----- nm Forward Voltage VF ----- 3.5 4.0 V Reverse Current IR ----- ----- 50 μA Condition nm IF=20mA VR=5V Notes: 1.Tolerance of Luminous Intensity ±10% 2.Tolerance of Dominant Wavelength ±1nm 3.Tolerance of Forward Voltage ±0.1V Everlight Electronics Co., Ltd. Device No:SZDSE-193-G03 http://www.everlight.com Prepared date: 8-5-2004 Rev. 1 Page: 3 of 10 Prepared by: Aihua hong EVERLIGHT ELECTRONICS CO.,LTD. 19-213/GHC-YR1S2/3T Bin Rang Of Dom. Wavelength Group Y Bin Min Max X 520 525 Y 525 530 Z 530 535 Unit Condition nm IF=20mA Bin Rang Of Luminous Intensity Bin Min Max R1 112 140 R2 140 180 S1 180 225 S2 225 285 Unit Condition mcd IF=20mA Notes: 1.Tolerance of Luminous Intensity ±10% 2.Tolerance of Dominant Wavelength ±1nm 3.Tolerance of Forward Voltage ±0.1V Everlight Electronics Co., Ltd. Device No:SZDSE-193-G03 http://www.everlight.com Prepared date: 8-5-2004 Rev. 1 Page: 4 of 10 Prepared by: Aihua hong EVERLIGHT ELECTRONICS CO.,LTD. 19-213/GHC-YR1S2/3T Typical Electro-Optical Characteristics Curves Everlight Electronics Co., Ltd. Device No:SZDSE-193-G03 http://www.everlight.com Prepared date: 8-5-2004 Rev. 1 Page: 5 of 10 Prepared by: Aihua hong EVERLIGHT ELECTRONICS CO.,LTD. 19-213/GHC-YR1S2/3T Label explanation CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank REF: Forward Voltage Rank Reel Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. Device No:SZDSE-193-G03 http://www.everlight.com Prepared date: 8-5-2004 Rev. 1 Page: 6 of 10 Prepared by: Aihua hong EVERLIGHT ELECTRONICS CO.,LTD. 19-213/GHC-YR1S2/3T Carrier Tape Dimensions: Loaded quantity 3000 PCS per reel Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Moisture Resistant Packaging Label Aluminum moistue-proof bag Everlight Electronics Co., Ltd. Device No:SZDSE-193-G03 http://www.everlight.com Prepared date: 8-5-2004 Desiccant Rev. 1 Label Page: 7 of 10 Prepared by: Aihua hong EVERLIGHT ELECTRONICS CO.,LTD. 19-213/GHC-YR1S2/3T Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% Test Sample Hours/Cycles Size No. Items Test Condition 1 Reflow Soldering Temp. : 260℃±5℃ Min. 5sec. 6 Min. 22 PCS. 0/1 Temperature Cycle H : +100℃ 15min ∫ 5 min L : -40℃ 15min 300 Cycles 22 PCS. 0/1 Thermal Shock H : +100℃ 5min ∫ 10 sec L : -10℃ 5min 300 Cycles 22 PCS. 0/1 Temp. : 100℃ 1000 Hrs. 22 PCS. 0/1 Temp. : -40℃ 1000 Hrs. 22 PCS. 0/1 2 3 4 5 High Temperature Storage Low Temperature Storage Ac/Re 6 DC Operating Life IF = 20 mA 1000 Hrs. 22 PCS. 0/1 7 High Temperature / High Humidity 85℃/ 85%RH 1000 Hrs. 22 PCS. 0/1 Everlight Electronics Co., Ltd. Device No:SZDSE-193-G03 http://www.everlight.com Prepared date: 8-5-2004 Rev. 1 Page: 8 of 10 Prepared by: Aihua hong EVERLIGHT ELECTRONICS CO.,LTD. 19-213/GHC-YR1S2/3T Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. Device No:SZDSE-193-G03 http://www.everlight.com Prepared date: 8-5-2004 Rev. 1 Page: 9 of 10 Prepared by: Aihua hong EVERLIGHT ELECTRONICS CO.,LTD. 19-213/GHC-YR1S2/3T 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 280℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Reliability AndR.O.C Conditions Tucheng,Test TaipeiItems 236, Taiwan, Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com The reliability of products shall be satisfied with items listed below. Everlight Electronics Co., Ltd. Device No:SZDSE-193-G03 http://www.everlight.com Prepared date: 8-5-2004 Rev. 1 Page: 10 of 10 Prepared by: Aihua hong