EVERLIGHT ELECTRONICS CO.,LTD. Technical Data Sheet Chip LED with Bi-Color(Multi-Color) 19-223/R6G6C-A01/2T Features ․Package in 8mm tape on 7〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Multi-color type. ․Pb-free. ․The product itself will remain within RoHS compliant version. Descriptions ․The 19-223 SMD Taping is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. ․Besides, lightweight makes them ideal for miniature applications. etc. Applications ․Backlighting in dashboard and switch. ․Telecommunication: indicator and backlighting in telephone and fax. ․Flat backlight for LCD, switch and symbol. ․General use. Device Selection Guide Chip Emitted Color Type Material R6 AlGaInP Brilliant Red G6 AlGaInP Brilliant Yellow Green Lens Color Water Clear Everlight Electronics Co., Ltd. http://www.everlight.com Device No: SZDSE-192-A25 Prepared date: 7-Nov-2006 Rev 1 Page: 1 of 11 Prepared by: Xiaoyan EVERLIGHT ELECTRONICS CO.,LTD. 19-223/R6G6C-A01/2T Package Outline Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Device No: SZDSE-192-A25 Prepared date: 7-Nov-2006 Rev 1 Page: 2 of 11 Prepared by: Xiaoyan EVERLIGHT ELECTRONICS CO.,LTD. 19-223/R6G6C-A01/2T Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Unit Reverse Voltage VR 5 V Forward Current IF 25 mA Peak Forward Current R6:60 IFP mA (Duty 1/10 @1KHz) G6:60 R6:60 Power Dissipation Pd mW G6:60 R6:2000 Electrostatic Discharge(HBM) ESD V G6:2000 Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +90 ℃ Soldering Temperature Tsol Reflow Soldering : 260 ℃ for 10 sec. Hand Soldering : 350 ℃ for 3 sec. Electro-Optical Characteristics (Ta=25℃) Parameter Symbol Iv R6 Min. 72.0 Luminous Intensity Viewing Angle 2θ1/2 λp ----- R6 624 R6 ----- Note: VF IR R6 G6 R6 G6 ----- ----575 G6 Reverse Current 130 G6 G6 Forward Voltage mcd deg 632 ----- △λ Condition 57.0 ----λd Unit 180 22.5 R6 Peak Wavelength Spectrum Radiation Bandwidth Max. ----G6 Dominant Wavelength Typ. 573 20 20 nm IF=20mA ----- nm ----- nm 1.7 2.0 2.4 1.7 2.0 2.4 ----- ----- 10 V μA 10 VR=5V 1.Tolerance of Luminous Intensity ±11% Everlight Electronics Co., Ltd. http://www.everlight.com Device No: SZDSE-192-A25 Prepared date: 7-Nov-2006 Rev 1 Page: 3 of 11 Prepared by: Xiaoyan EVERLIGHT ELECTRONICS CO.,LTD. 19-223/R6G6C-A01/2T R6 Bin Range Of Luminous Intensity Bin Min Max Q 72.0 112 R 112 180 Unit Condition mcd IF=20mA Unit Condition mcd IF=20mA G6 Bin Range Of Luminous Intensity Bin Min Max 1 22.5 36.0 2 36.0 57.0 Note: 1.Tolerance of Luminous Intensity ±11% Everlight Electronics Co., Ltd. http://www.everlight.com Device No: SZDSE-192-A25 Prepared date: 7-Nov-2006 Rev 1 Page: 4 of 11 Prepared by: Xiaoyan EVERLIGHT ELECTRONICS CO.,LTD. 19-223/R6G6C-A01/2T Typical Electro-Optical Characteristics Curves R6 Everlight Electronics Co., Ltd. http://www.everlight.com Device No: SZDSE-192-A25 Prepared date: 7-Nov-2006 Rev 1 Page: 5 of 11 Prepared by: Xiaoyan EVERLIGHT ELECTRONICS CO.,LTD. 19-223/R6G6C-A01/2T Typical Electro-Optical Characteristics Curves G6 Everlight Electronics Co., Ltd. http://www.everlight.com Device No: SZDSE-192-A25 Prepared date: 7-Nov-2006 Rev 1 Page: 6 of 11 Prepared by: Xiaoyan EVERLIGHT ELECTRONICS CO.,LTD. 19-223/R6G6C-A01/2T Label explanation CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank xxxxxx xxxxxx RoHS xxxxxxxxxxxx xxxx REF: Forward Voltage Rank xxxxxxxx Reel Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Device No: SZDSE-192-A25 Prepared date: 7-Nov-2006 Rev 1 Page: 7 of 11 Prepared by: Xiaoyan EVERLIGHT ELECTRONICS CO.,LTD. 19-223/R6G6C-A01/2T Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Moisture Resistant Packaging Label Aluminum moisture-proof bag Everlight Electronics Co., Ltd. http://www.everlight.com Device No: SZDSE-192-A25 Prepared date: 7-Nov-2006 Desiccant Label Rev 1 Page: 8 of 11 Prepared by: Xiaoyan EVERLIGHT ELECTRONICS CO.,LTD. 19-223/R6G6C-A01/2T Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% Test Sample Hours/Cycles Size No. Items Test Condition 1 Reflow Soldering Temp. : 260℃±5℃ Min. 5sec. 6 Min. 22 PCS. 0/1 Temperature Cycle H : +100℃ 15min ∫ 5 min L : -40℃ 15min 300 Cycles 22 PCS. 0/1 Thermal Shock H : +100℃ 5min ∫ 10 sec L : -10℃ 5min 300 Cycles 22 PCS. 0/1 Temp. : 100℃ 1000 Hrs. 22 PCS. 0/1 Temp. : -40℃ 1000 Hrs. 22 PCS. 0/1 2 3 4 5 High Temperature Storage Low Temperature Storage Ac/Re 6 DC Operating Life IF = 20 mA 1000 Hrs. 22 PCS. 0/1 7 High Temperature / High Humidity 85℃/ 85%RH 1000 Hrs. 22 PCS. 0/1 Everlight Electronics Co., Ltd. http://www.everlight.com Device No: SZDSE-192-A25 Prepared date: 7-Nov-2006 Rev 1 Page: 9 of 11 Prepared by: Xiaoyan EVERLIGHT ELECTRONICS CO.,LTD. 19-223/R6G6C-A01/2T Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 After opening the package: The LED's floor life is 1 year under 30℃ or less and 60% RH or less. If unused LEDs remain, it should be stored in moisture proof packages. 2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. Everlight Electronics Co., Ltd. http://www.everlight.com Device No: SZDSE-192-A25 Prepared date: 7-Nov-2006 Rev 1 Page: 10 of 11 Prepared by: Xiaoyan EVERLIGHT ELECTRONICS CO.,LTD. 19-223/R6G6C-A01/2T 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com Everlight Electronics Co., Ltd. http://www.everlight.com Device No: SZDSE-192-A25 Prepared date: 7-Nov-2006 Rev 1 Page: 11 of 11 Prepared by: Xiaoyan