Technical Data Sheet 1.6×0.8mm Package Infrared LED HIR83-01B/TR8 Features ․Peak wavelength λp=850nm ․Low forward voltage ․Pb free ․The product itself will remain within RoHS compliant version. Descriptions ․HIR83-01B/TR8 is an infrared emitting diode in miniature SMD package which is molded in a black plastic with semicircle and top view lens. ․The device is spectrally matched with silicon photodiode and phototransistor. Applications ․Infrared applied system Device Selection Guide LED Part No. Chip Material HIR83-01B/TR8 GaAlAs Everlight Electronics Co., Ltd. Device No：DIR-0000353 Revision :1 LifecyclePhase: Lens Color Black http://www.everlight.com Prepared date：0629-2010 Rev 1 Page: 1 of 9 Prepared by：JAINE TSAI Release Date:2010-07-06 20:13:37.0 Expired Period: Forever HIR83-01B/TR8 Package Dimensions 1 2 1 2 Anode Cathode Notes: 1.All dimensions are in millimeters 2.Tolerances unless dimensions ±0.1mm Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Continuous Forward Current IF 65 Units mA Peak Forward Current IFP 1.0 A Reverse Voltage VR 5 V Operating Temperature Topr -40 ~ +100 ℃ Storage Temperature Tstg -40 ~ +100 ℃ Tsol 260 ℃ Pd 100 mW Soldering Temperature *1 *2 Power Dissipation at(or below) 25℃Free Air Temperature Notes: *1:IFP Conditions--Pulse Width≦100μs and Duty≦1%. *2:Soldering time≦5 seconds. Everlight Electronics Co., Ltd. Device No：DIR-0000353 Revision :1 LifecyclePhase: http://www.everlight.com Prepared date：0629-2010 Rev 1 Page: 2 of 9 Prepared by：JAINE TSAI Release Date:2010-07-06 20:13:37.0 Expired Period: Forever HIR83-01B/TR8 Electro-Optical Characteristics (Ta=25℃) Parameter Symbol Ie λp Condition IF=20mA Min. Typ. Max. 2.0 5.0 IF=100mA 840 850 Δλ IF=100mA -- Forward Voltage VF IF=20mA Reverse Current VR=5V Rise time IR tr --- 30 1.4 -- -870 -- IF=20mA -- Fall time tf IF=20mA IF =20mA (X) IF =20mA (Y) ---- Radiant Intensity Peak Wavelength Spectral Bandwidth View Angle 2θ1/2 Everlight Electronics Co., Ltd. Device No：DIR-0000353 Revision :1 LifecyclePhase: http://www.everlight.com Prepared date：0629-2010 Rev 1 Units mW /sr nm nm V 1.7 10 μA 16 -- ns 30 100 40 ---- ns deg Page: 3 of 9 Prepared by：JAINE TSAI Release Date:2010-07-06 20:13:37.0 Expired Period: Forever HIR83-01B/TR8 Typical Electro-Optical Characteristics Curves Fig.1 Forward Current vs. Ambient Temperature Fig.2 Spectral Distributio n 140 100 IF=20mA Ta=25° C 120 80 100 80 60 60 40 40 20 20 0 0 -40 -20 0 790 810 830 850 870 890 910 930 950 20 40 60 80 100 Fig.3 Peak Emission Wavelength Ambient Temperature Fig.4 Forward Current vs. Forward Voltage 10 900 875 4 3 10 850 2 10 825 800 -25 1 10 0 25 Everlight Electronics Co., Ltd. Device No：DIR-0000353 Revision :1 LifecyclePhase: 50 75 100 0 http://www.everlight.com Prepared date：0629-2010 1 2 3 Rev 1 4 5 6 7 8 Page: 4 of 9 Prepared by：JAINE TSAI Release Date:2010-07-06 20:13:37.0 Expired Period: Forever HIR83-01B/TR8 Typical Electro-Optical Characteristics Curves Fig.5 Relative Radiant Intensity vs. Angular Displacement (X axle) (Y axle) -20 -10 0 10 20 -20 -10 0 10 20 30 1.0 40 1.0 40 0.9 50 0.9 50 0.8 0.7 60 0.8 0.7 60 70 80 0.6 0.4 0.2 0 Everlight Electronics Co., Ltd. Device No：DIR-0000353 Revision 30 :1 LifecyclePhase: 0.2 0.4 0.6 70 80 0.6 0.4 0.2 http://www.everlight.com Prepared date：0629-2010 Rev 1 0 0.2 0.4 0.6 Page: 5 of 9 Prepared by：JAINE TSAI Release Date:2010-07-06 20:13:37.0 Expired Period: Forever HIR83-01B/TR8 Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. Device No：DIR-0000353 Revision :1 LifecyclePhase: http://www.everlight.com Prepared date：0629-2010 Rev 1 Page: 6 of 9 Prepared by：JAINE TSAI Release Date:2010-07-06 20:13:37.0 Expired Period: Forever HIR83-01B/TR8 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. Everlight Electronics Co., Ltd. Device No：DIR-0000353 Revision :1 LifecyclePhase: http://www.everlight.com Prepared date：0629-2010 Rev 1 Page: 7 of 9 Prepared by：JAINE TSAI Release Date:2010-07-06 20:13:37.0 Expired Period: Forever HIR83-01B/TR8 Package Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm 2. Carrier Tape Dimensions:(Quantity: 2000pcs/reel) 1 2 1 2 1 2 Anode Cathode Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. Device No：DIR-0000353 Revision :1 LifecyclePhase: http://www.everlight.com Prepared date：0629-2010 Rev 1 Page: 8 of 9 Prepared by：JAINE TSAI Release Date:2010-07-06 20:13:37.0 Expired Period: Forever HIR83-01B/TR8 Packing Procedure Aluminum moistue-proof bag Label Desiccant Label Label Form Specification Pb EVERLIGHT CPN : P N RoHS HIR83-01B/TR8 CAT : HUE : REF : QTY :2000 LOT NO : Reference : CPN: Customer’s Production Number P/N : Production Number QTY: Packing Quantity CAT: Ranks HUE: Peak Wavelength REF: Reference LOT No: Lot Number MADE IN TAIWAN: Production Place MADE IN TAIWAN Notes 1. Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification. 2. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 3. These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don’t reproduce or cause anyone to reproduce them without EVERLIGHT’s consent. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Everlight Electronics Co., Ltd. Device No：DIR-0000353 Revision :1 LifecyclePhase: Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com http://www.everlight.com Prepared date：0629-2010 Rev 1 Page: 9 of 9 Prepared by：JAINE TSAI Release Date:2010-07-06 20:13:37.0 Expired Period: Forever