EVERLIGHT HIR89-01C-1R

Technical Data Sheet
Infrared MIDLED LED
HIR89-01C/1R
Features
․Low forward voltage.
․View angle 30° (Typ.)
․Pb free
․The product itself will remain within RoHS compliant version.
․Compatible with infrared and vapor phase reflow solder process
․Taping as Top view.
Descriptions
․HIR89-01C/1R is an infrared emitting diode with miniature MIDLED package.
The device is spectrally matched with silicon photodiode and phototransistor.
Applications
․Infrared applied system
Device Selection Guide
LED Part No.
Chip
Material
Lens Color
HIR89-01C/1R
GaAlAs
Water clear
Everlight Electronics Co., Ltd.
Device No:DIR-0000413
Revision
:1
LifecyclePhase:
http://www.everlight.com
Rev 1
Prepared date:12-10-2010
Page: 1 of 10
Prepared by:JAINE TSAI
Release Date:2010-12-16 13:53:02.0
Expired Period: Forever
HIR89-01C/1R
Package Dimensions
Notes: 1.All dimensions are in millimeters
2.Tolerances unless dimensions ±0.1mm
Everlight Electronics Co., Ltd.
Device No:DIR-0000413
Revision
:1
LifecyclePhase:
http://www.everlight.com
Rev 1
Prepared date:12-10-2010
Page: 2 of 10
Prepared by:JAINE TSAI
Release Date:2010-12-16 13:53:02.0
Expired Period: Forever
HIR89-01C/1R
Absolute Maximum Ratings (Ta=25℃)
Parameter
Symbol
Rating
IF
65
Units
mA
IFP
200
mA
Reverse Voltage
VR
5
V
Operating Temperature
Topr
-40~ +85
℃
Storage Temperature
Tstg
-40 ~ +100
℃
Tsol
260
℃
Pd
100
mW
Continuous Forward Current
Peak Forward Current
*1
Soldering Temperature
*2
Power Dissipation at(or below)
25℃Free Air Temperature
Notes: *1:IFP Conditions--Pulse Width≦500μs and Duty≦5%.
*2:Soldering time≦5 seconds.
Electro-Optical Characteristics (Ta=25℃)
Parameter
Radiant Intensity
Peak Wavelength
Spectral Bandwidth
Symbol
IE
λp
Condition
IF=70mA ,tp=20ms
Min.
Typ.
Max.
25
--
IF=100mA
840
Δλ
IF=100mA
IF=20mA
--
850
30
125
870
--
1.40
1.70
1.55
--
1.90
10
μA
--
Unit
mW/sr
nm
nm
V
Forward Voltage
VF
IF=70mA,tp=20ms
Reverse Current
IR
tr
VR=5V
---
IF=20mA
--
16
--
ns
tf
2θ1/2
IF=20mA
IF=20mA
---
30
30
---
ns
deg
Bin Number
B
C
D
Min
25
40
63
Max
50
80
125
Rise time
Fall time
View Angle
Rank
Condition:IF=70mA
Unit:mW/sr
Everlight Electronics Co., Ltd.
Device No:DIR-0000413
Revision
:1
LifecyclePhase:
http://www.everlight.com
Rev 1
Prepared date:12-10-2010
Page: 3 of 10
Prepared by:JAINE TSAI
Release Date:2010-12-16 13:53:02.0
Expired Period: Forever
HIR89-01C/1R
Typical Electro-Optical Characteristics Curves
Fig.1 Forward Current vs.
Ambient Temperature
Fig.2 Spectral Distributio n
140
100
120
IF=20mA
Ta=25° C
80
100
60
80
60
40
40
20
20
0
0
790 810 830 850 870 890 910 930 950
20 40 60 80 100
-40 -20 0
Fig.3 Peak Emission Wavelength
Ambient Temperature
Fig.4 Forward Current
vs. Forward Voltage
4
10
900
875
3
10
850
2
10
825
800
-25
1
10
0
25
Everlight Electronics Co., Ltd.
Device No:DIR-0000413
Revision
:1
LifecyclePhase:
50
75
100
0
1
http://www.everlight.com
2
3
Rev 1
Prepared date:12-10-2010
4
5
6
7
8
Page: 4 of 10
Prepared by:JAINE TSAI
Release Date:2010-12-16 13:53:02.0
Expired Period: Forever
HIR89-01C/1R
Typical Electro-Optical Characteristics Curves
Fig.5 Relative Intensity vs.
Fig.6 Relative Radiant Intensity vs.
Forward Current
Angular Displacement
-20
Ie-Radiant Intensity(mW/sr)
1000
0
-10
10
20
30
100
10
0
10
0
10
1
2
10
10
3
10 4
1.0
40
0.9
50
0.8
0.7
60
70
80
0.6 0.4 0.2
0
0.2 0.4 0.6
IF-Forward Current (mA)
Everlight Electronics Co., Ltd.
Device No:DIR-0000413
Revision
:1
LifecyclePhase:
http://www.everlight.com
Rev 1
Prepared date:12-10-2010
Page: 5 of 10
Prepared by:JAINE TSAI
Release Date:2010-12-16 13:53:02.0
Expired Period: Forever
HIR89-01C/1R
Precautions For Use
1. Over-current-proof
Customer must apply resistors for protection , otherwise slight voltage shift will cause big
current change ( Burn out will happen ).
2. Storage
2.1 Do not open moisture proof bag before devices are ready to use.
2.2 Shelf life in sealed bag from the bag seal date:
18 months at 10°C~30°C and < 90% RH.
2.3 After opening the package, the devices must be stored at 10°C~30°C and  60%RH, and used
within 72 hours(floor life).
2.4 If the moisture absorbent material(desiccant material) has faded or unopened bag has
exceeded the shelf life or devices(out of bag) have exceeded the floor life, baking treatment is
required.
2.5 If baking is required, refer to IPC/JEDEC J-STD-033 for bake procedure or recommend the
following conditions :
192 hours at 40°C +5/–0°C and < 5 % RH (reeled/tubed/loose units) or
96 hours at 60°C ± 5°C and < 5 % RH (reeled/tubed/loose units) or
24 hours at 125°C ± 5°C, not suitable for reel or tubes.
Everlight Electronics Co., Ltd.
Device No:DIR-0000413
Revision
:1
LifecyclePhase:
http://www.everlight.com
Rev 1
Prepared date:12-10-2010
Page: 6 of 10
Prepared by:JAINE TSAI
Release Date:2010-12-16 13:53:02.0
Expired Period: Forever
HIR89-01C/1R
3. Soldering Condition
3.1 Pb-free solder temperature profile
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
Everlight Electronics Co., Ltd.
Device No:DIR-0000413
Revision
:1
LifecyclePhase:
http://www.everlight.com
Rev 1
Prepared date:12-10-2010
Page: 7 of 10
Prepared by:JAINE TSAI
Release Date:2010-12-16 13:53:02.0
Expired Period: Forever
HIR89-01C/1R
4.Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3
seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more
intervals, and do soldering of each terminal. Be careful because the damage of the product is often
started at the time of the hand solder.
5.Repairing
Repair should not be done after the LEDs have been soldered. When repairing is
unavoidable, a double-head soldering iron should be used (as below figure). It should be
confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by
repairing.
Everlight Electronics Co., Ltd.
Device No:DIR-0000413
Revision
:1
LifecyclePhase:
http://www.everlight.com
Rev 1
Prepared date:12-10-2010
Page: 8 of 10
Prepared by:JAINE TSAI
Release Date:2010-12-16 13:53:02.0
Expired Period: Forever
HIR89-01C/1R
Package Dimensions
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
2. Carrier Tape Dimensions:(Quantity: 2000pcs/reel)
1
2
1
2
1
2
Anode
Cathode
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
Everlight Electronics Co., Ltd.
Device No:DIR-0000413
Revision
:1
LifecyclePhase:
http://www.everlight.com
Rev 1
Prepared date:12-10-2010
Page: 9 of 10
Prepared by:JAINE TSAI
Release Date:2010-12-16 13:53:02.0
Expired Period: Forever
HIR89-01C/1R
Packing Procedure
Aluminum moistue-proof bag
Label
Desiccant
Label
Label Form Specification
Pb
EVERLIGHT
CPN :
P N
RoHS
CAT :
HUE :
REF :
QTY :
LOT NO :
Reference :
CPN: Customer’s Production Number
P/N : Production Number
QTY: Packing Quantity
CAT: Ranks
HUE: Peak Wavelength
REF: Reference
LOT No: Lot Number
MADE IN TAIWAN: Production Place
MADE IN TAIWAN
Notes
1. Above specification may be changed without notice. EVERLIGHT will reserve authority on
material change for above specification.
2. When using this product, please observe the absolute maximum ratings and the instructions
for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for
any damage resulting from use of the product which does not comply with the absolute
maximum ratings and the instructions included in these specification sheets.
3. These specification sheets include materials protected under copyright of EVERLIGHT
corporation. Please don’t reproduce or cause anyone to reproduce them without
EVERLIGHT’s consent.
EVERLIGHT ELECTRONICS CO., LTD.
Office: No 25, Lane 76, Sec 3, Chung Yang Rd,
Tucheng, Taipei 236, Taiwan, R.O.C
Everlight Electronics Co., Ltd.
Device No:DIR-0000413
Revision
:1
LifecyclePhase:
Tel: 886-2-2267-2000, 2267-9936
Fax: 886-2267-6244, 2267-6189, 2267-6306
http://www.everlight.com
http://www.everlight.com
Rev 1
Prepared date:12-10-2010
Page: 10 of 10
Prepared by:JAINE TSAI
Release Date:2010-12-16 13:53:02.0
Expired Period: Forever