Technical Data Sheet 0603 Package Infrared Chip LED SIR19-315/TR8 Features ․Small double-end package ․Peak wavelength λp=870nm ․Package in 8mm tape on 7” diameter reel ․Compatible with infrared and vapor phase reflow solder process. ․Pb free ․RoHS refer to SMD B type SGS report Descriptions ․SIR19-315/TR8 is an infrared emitting diode in miniature SMD package which is molded in a water clear epoxy. ․The device is spectrally matched with silicon photodiode and phototransistor. Applications ․PCB mounted infrared sensor ․Infrared remote control units with high power requirement ․Scanner ․Infrared applied system Device Selection Guide LED Part No. Chip Material Lens Color SIR AlGaAs Water clear Everlight Electronics Co., Ltd. Device No：DTS-193-193 http:\\www.everlight.com Prepared date：02-15-2006 Rev 1 Page: 1 of 9 Prepared by：Posen Hsu SIR19-315/TR8 Package Dimensions Notes: 1.All dimensions are in millimeters 2.Tolerances unless dimensions ±0.1mm Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Continuous Forward Current IF 70 Units mA Reverse Voltage VR 5 V Operating Temperature Topr -25 ~ +85 ℃ Storage Temperature Tstg -40 ~ +85 ℃ Soldering Temperature Tsol 260 ℃ Power Dissipation at(or below) 25℃Free Air Temperature Pd 110 mW Notes: * Soldering time≦5 seconds. Everlight Electronics Co., Ltd. Device No：DTS-193-193 http:\\www.everlight.com Prepared date：02-15-2006 Rev 1 Page: 2 of 9 Prepared by：Posen Hsu SIR19-315/TR8 Electro-Optical Characteristics (Ta=25℃) Parameter Symbol Ie λp Condition IF=20mA Min. Typ. Max. 1.0 1.3 IF=20mA 860 870 -900 Δλ IF=20mA -- 45 -- nm Forward Voltage VF IF=20mA IR 2θ1/2 VR=5V 1.35 -- 1.70 10 V Reverse Current 1.20 -- IF=20mA -- 140 -- Radiant Intensity Peak Wavelength Spectral Bandwidth View Angle Everlight Electronics Co., Ltd. Device No：DTS-193-193 http:\\www.everlight.com Prepared date：02-15-2006 Rev 1 Units mW /sr nm μA deg Page: 3 of 9 Prepared by：Posen Hsu SIR19-315/TR8 Typical Electro-Optical Characteristics Curves Fig.1 Forward Current vs. Ambient Temperature Fig.2 Spectral Distribution 140 100 IF=20mA Ta=25°C 120 80 100 60 80 60 40 40 20 20 0 0 -25 -20 0 20 40 60 80 100 Fig.3 Peak Emission Wavelength Ambient Temperature 810 830 850 870 890 910 930 950 970 Fig.4 Forward Voltage vs. Ambient Temperature(°C) 1.5 910 890 1.4 IF=20mA 870 1.3 850 830 -25 1.2 0 25 Everlight Electronics Co., Ltd. Device No：DTS-193-193 50 75 100 25 http:\\www.everlight.com Prepared date：02-15-2006 50 Rev 1 75 100 120 Page: 4 of 9 Prepared by：Posen Hsu SIR19-315/TR8 Typical Electro-Optical Characteristics Curves Fig.5 Relative Intensity vs. Fig.6 Relative Radiant Intensity vs. Ambient Temperature(°C) Angular Displacement -20 2.0 -10 0 10 20 30 1.5 IF=20mA 1.0 1.0 40 0.9 50 0.8 0.7 60 70 80 0 25 50 100 75 120 0.6 0.4 0.2 0 0.2 0.4 0.6 . Everlight Electronics Co., Ltd. Device No：DTS-193-193 http:\\www.everlight.com Prepared date：02-15-2006 Rev 1 Page: 5 of 9 Prepared by：Posen Hsu SIR19-315/TR8 Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. Device No：DTS-193-193 http:\\www.everlight.com Prepared date：02-15-2006 Rev 1 Page: 6 of 9 Prepared by：Posen Hsu SIR19-315/TR8 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 280℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. Everlight Electronics Co., Ltd. Device No：DTS-193-193 http:\\www.everlight.com Prepared date：02-15-2006 Rev 1 Page: 7 of 9 Prepared by：Posen Hsu SIR19-315/TR8 Package Dimensions Taping Dimensions Unit: mm Everlight Electronics Co., Ltd. Device No：DTS-193-193 http:\\www.everlight.com Prepared date：02-15-2006 Rev 1 Page: 8 of 9 Prepared by：Posen Hsu SIR19-315/TR8 Packing Quantity Specification 1.3000Pcs/1Volume，1Volume/1Bag 2.10Boxes/1Carton Label Form Specification CPN: Customer’s Production Number P/N : Production Number QTY: Packing Quantity CAT: Ranks HUE: Peak Wavelength REF: Reference LOT No: Lot Number MADE IN TAIWAN: Production Place RoHS SIR19-315/TR8 Notes 1. Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification. 2. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 3. These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don’t reproduce or cause anyone to reproduce them without EVERLIGHT’s consent. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Everlight Electronics Co., Ltd. Device No：DTS-193-193 Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http:\\www.everlight.com http:\\www.everlight.com Prepared date：02-15-2006 Rev 1 Page: 9 of 9 Prepared by：Posen Hsu