HMC530LP5 / 530LP5E v07.0411 MMIC VCO w/ HALF FREQUENCY OUTPUT & DIVIDE-BY-4, 9.5 - 10.8 GHz Typical Applications Features Low noise MMIC VCO w/Half Frequency, Divide-by-4 Outputs for: Triple Output: Fo = 9.5 - 10.8 GHz Fo/2 = 4.75 - 5.4 GHz Fo/4 = 2.38 - 2.7 GHz • Point to Point/Multipoint Radio • Test Equipment & Industrial Controls Pout: +11 dBm Phase Noise: -110 dBc/Hz @100 kHz Typ. • SATCOM • Military End-Use No External Resonator Needed 32 Lead 5 x 5 mm SMT Package: 25 mm² Functional Diagram The HMC530LP5 & HMC530LP5E are GaAs InGaP Heterojunction Bipolar Transistor (HBT) MMIC VCOs. The HMC530LP5 & HMC530LP5E integrate resonators, negative resistance devices, varactor diodes and feature half frequency and divide-by-4 outputs. The VCO’s phase noise performance is excellent over temperature, shock, and process due to the oscillator’s monolithic structure. Power output is +11 dBm typical from a +5V supply voltage. The prescaler and RF/2 functions can be disabled to conserve current if not required. The voltage controlled oscillator is packaged in a leadless QFN 5x5 mm surface mount package, and requires no external matching components. VCOS with Fo/2 OUTPUT - SMT 8 8-1 General Description Electrical Specifications, TA = +25° C, Vcc (Dig), Vcc (Amp), Vcc (RF) = +5V Parameter Frequency Range Power Output Min. Fo Fo/2 RFOUT RFOUT/2 RFOUT/4 Supply Current Max. 9.5 - 10.8 4.75 - 5.4 +8 +8 -8 SSB Phase Noise @ 100 kHz Offset, Vtune= +5V @ RFOUT Tune Voltage Typ. GHz GHz +14 +14 -3 -110 Vtune Icc(Dig) + Icc(Amp) + Icc(RF) 2 290 350 Tune Port Leakage Current (Vtune= 13V) Output Return Loss Units dBm dBm dBm dBc/Hz 12 V 390 mA 10 µA 5 dB 30 20 30 dBc dBc dBc Pulling (into a 2.0:1 VSWR) 7 MHz pp Pushing @ Vtune= 5V 20 MHz/V Frequency Drift Rate 1 MHz/°C Harmonics/Subharmonics 1/2 2nd 3rd For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC530LP5 / 530LP5E v07.0411 MMIC VCO w/ HALF FREQUENCY OUTPUT & DIVIDE-BY-4, 9.5 - 10.8 GHz Frequency vs. Tuning Voltage, T= 25°C 11.2 11.2 10.8 10.8 OUTPUT FREQUENCY (GHz) 10.4 10 9.6 9.2 +25C +85C -40C 8.8 8.4 8 10.4 10 9.6 9.2 Vcc=4.75V Vcc=5.00V Vcc=5.25V 8.8 8.4 8 0 1 2 3 4 5 6 7 8 9 10 11 12 13 0 1 2 3 TUNING VOLTAGE (V) 6 7 8 9 10 11 12 13 Output Power vs. Tuning Voltage, Vcc = +5V 700 16 8 14 OUTPUT POWER (dBm) 600 SENSITIVITY (MHz/Volt) 5 TUNING VOLTAGE (V) Sensitivity vs. Tuning Voltage, Vcc = +5V +25C +85C -40C 500 400 300 200 100 12 10 8 6 +25C +85C -40C 4 2 0 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 0 1 2 3 TUNING VOLTAGE (V) 4 5 6 7 8 9 10 11 12 13 TUNING VOLTAGE (V) SSB Phase Noise vs. Tuning Voltage SSB Phase Noise @ Vtune = +5V 0 SSB PHASE NOISE (dBc/Hz) -75 SSB PHASE NOISE (dBc/Hz) 4 -85 -95 10khz 100khz -105 -115 -20 +25C +85C -40C -40 -60 -80 -100 -120 -140 -160 -125 0 1 2 3 4 5 6 7 8 9 TUNING VOLTAGE (V) 10 11 12 13 -180 2 10 10 3 10 4 10 5 10 6 10 7 VCOS with Fo/2 OUTPUT - SMT OUTPUT FREQUENCY (GHz) Frequency vs. Tuning Voltage, Vcc = +5V OFFSET FREQUENCY (Hz) For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 8-2 HMC530LP5 / 530LP5E v07.0411 MMIC VCO w/ HALF FREQUENCY OUTPUT & DIVIDE-BY-4, 9.5 - 10.8 GHz RFOUT/2 Output Power vs. Tuning Voltage, Vcc = +5V 5.6 16 5.4 14 OUTPUT POWER (dBm) OUTPUT FREQUENCY (GHz) RFOUT/2 Frequency vs. Tuning Voltage, Vcc = +5V 5.2 5 4.8 4.6 +25C +85C -40C 4.4 4.2 12 10 8 6 +25C +85C -40C 4 2 4 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 0 1 2 3 TUNING VOLTAGE (V) 2.7 OUTPUT POWER (dBm) OUTPUT FREQUENCY (GHz) VCOS with Fo/2 OUTPUT - SMT 8-3 0 -1 2.6 2.5 2.4 +25C +85C -40C 2.2 4 5 6 7 8 10 11 12 13 10 11 12 13 -5 -6 -7 -8 -9 3 9 -4 -10 2 8 9 10 11 12 13 +25C +85C -40C -3 2 1 7 -2 2.1 0 6 Divide-by-4 Output Power vs. Tuning Voltage, Vcc = +5V 2.8 2.3 5 TUNING VOLTAGE (V) Divide-by-4 Frequency vs. Tuning Voltage, Vcc = +5V 8 4 0 1 2 3 Absolute Maximum Ratings 4 5 6 7 8 9 TUNING VOLTAGE (V) TUNING VOLTAGE (V) Typical Supply Current vs. Vcc Vcc(Dig), Vcc(Amp), Vcc(RF) +5.5 Vdc Vcc (V) Icc (mA) Vtune 0 to +15V 4.75 320 Junction Temperature 135 °C 5.00 350 Continuous Pdiss (T=85 °C) (derate 43.5 mW/C above 85 °C 2.17 W 5.25 380 Thermal Resistance (junction to ground paddle) 23 °C/W Storage Temperature -65 to +150 °C Operating Temperature -40 to +85 °C Note: VCO will operate over full voltage range shown above. ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC530LP5 / 530LP5E v07.0411 MMIC VCO w/ HALF FREQUENCY OUTPUT & DIVIDE-BY-4, 9.5 - 10.8 GHz Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 8 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. PAD BURR LENGTH SHALL BE 0.15 mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05 mm MAXIMUM. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Package Information Part Number Package Body Material Lead Finish MSL Rating HMC530LP5 Low Stress Injection Molded Plastic Sn/Pb Solder MSL3 [1] HMC530LP5E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL3 [2] Package Marking [3] H530 XXXX H530 XXXX [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX Pin Descriptions Function Description 1 - 3, 8 - 10, 13 - 18, 20, 22 - 28, 30 - 32 Pin Number N/C No Connection. These pins may be connected to RF/ DC ground. Performance will not be affected. 4 RFOUT/4 Divide-by-4 output. DC block required. 6 Vcc (Dig) Supply voltage for prescaler. If prescaler is not required, this pin may be left open to conserve approximately 65 mA of current. Interface Schematic For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] VCOS with Fo/2 OUTPUT - SMT 5. PACKAGE WARP SHALL NOT EXCEED 0.05 mm. 8-4 HMC530LP5 / 530LP5E v07.0411 MMIC VCO w/ HALF FREQUENCY OUTPUT & DIVIDE-BY-4, 9.5 - 10.8 GHz Pin Descriptions VCOS with Fo/2 OUTPUT - SMT 8 8-5 Pin Number Function Description 7 Vcc (Amp) Supply voltage for RFOUT/2 output. If RFOUT/2 is not required, this pin may be left open to conserve approximately 30 mA of current. 12 RFOUT/2 Half frequency output (AC coupled). 19 RF OUT RF output (AC coupled). 21 Vcc (RF) Supply Voltage, +5V 29 VTUNE Control voltage and modulation input. Modulation bandwidth dependent on drive source impedance. See “Determining the FM Bandwidth of a Wideband Varactor Tuned VCO” application note. 5, 11, Paddle GND Package bottom has an exposed metal paddle that must be connected to RF/DC ground. Interface Schematic Typical Application Circuit For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC530LP5 / 530LP5E v07.0411 MMIC VCO w/ HALF FREQUENCY OUTPUT & DIVIDE-BY-4, 9.5 - 10.8 GHz Evaluation PCB List of Materials for Evaluation PCB 110227 [1] Item Description J1 - J4 PCB Mount SMA RF Connector J5 - J6 2 mm DC Header C1 - C3 100 pF Capacitor, 0402 Pkg. C4 1,000 pF Capacitor, 0402 Pkg. C5 - C7 2.2 µF Tantalum Capacitor U1 HMC530LP5(E) VCO PCB [2] 110225 Eval Board [1] Reference this number when ordering complete evaluation PCB The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and backside ground paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. VCOS with Fo/2 OUTPUT - SMT 8 [2] Circuit Board Material: Arlon 25FR For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 8-6