HITTITE HMC629LP4

HMC629LP4 / 629LP4E
v07.0410
ATTENUATORS - DIGITAL - SMT
8
3 dB LSB GaAs MMIC 4-BIT
DIGITAL ATTENUATOR, DC - 6 GHz
Typical Applications
Features
The HMC629LP4(E) is ideal for:
3 dB LSB Steps to 45 dB
• Cellular/3G Infrastructure
Power-Up State Selection
• WiBro / WiMAX / 4G
Low Insertion Loss: 2.5 dB
• Microwave Radio & VSAT
TTL/CMOS Compatible, Serial, Parallel
or Latched Parallel Control
• Test Equipment and Sensors
• IF & RF Applications
±0.25 dB Typical Step Error
Single +3V or +5V Supply
24 Lead 4x4mm SMT Package: 16mm2
Functional Diagram
General Description
The HMC629LP4(E) is a broadband 4-bit GaAs IC
Digital Attenuator in a low cost leadless SMT package.
This versatile digital attenuator incorporates off-chip
AC ground capacitors for near DC operation, making
it suitable for a wide variety of RF and IF applications.
The dual mode control interface is CMOS/TTL
compatible, and accepts either a three wire serial input
or a 4-bit parallel word. For applications which require
only 33 dB of attenuation range, the HMC629LP4(E)
provides excellent attenuation accuracy up to 10 GHz.
The HMC629LP4(E) is housed in a RoHS compliant
4x4 mm QFN leadless package, and requires no
external matching components.
Electrical Specifications,
TA = +25° C, 50 Ohm System, with Vdd = +5V & Vctl = 0/+5V (Unless Otherwise Noted)
Parameter
Min.
Typ.
Max.
Units
5
dB
dB
Insertion Loss
DC - 6
2.5
Attenuation Range
DC - 6
45
dB
Return Loss (ATTIN, ATTOUT, All Atten. States)
DC - 6
17
dB
± (0.50 + 5% of Atten. Setting) Max.
dB
dB
Attenuation Accuracy: (Referenced to Insertion Loss)
All Attenuation States
8-1
Frequency (GHz)
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC629LP4 / 629LP4E
v07.0410
3 dB LSB GaAs MMIC 4-BIT
DIGITAL ATTENUATOR, DC - 6 GHz
(Only Major States are Shown)
-5
-10
+25 C
+85 C
-40 C
-15
-20
-10
-20
-30
-40
-50
-60
0
2
4
6
8
10
0
2
FREQUENCY (GHz)
Input Return Loss
6
8
10
8
10
Output Return Loss
(Only Major States are Shown)
(Only Major States are Shown)
0
0
-5
-5
-10
-10
RETURN LOSS (dB)
RETURN LOSS (dB)
4
FREQUENCY (GHz)
-15
-20
-25
-30
-15
-20
-25
ATTENUATORS - DIGITAL - SMT
0
NORMALIZED ATTENUATION (dB)
INSERTION LOSS (dB)
0
-30
-35
-35
-40
-40
0
2
4
6
8
10
0
2
FREQUENCY (GHz)
4
6
FREQUENCY (GHz)
Bit Error vs. Frequency
Bit Error vs. Attenuation State
(Only Major States are Shown)
6
10
8
(1, 2, 4, 5) GHz
6
4
4
BIT ERROR (dB)
BIT ERROR (dB)
8
Normalized Attenuation
Insertion Loss vs. Temperature
2
0
-2
-4
2
0
-2
BIT 24
(7, 8, 10) GHz
-6
-4
-8
ALL BITS
-10
-6
0
5
10
15
20
25
30
ATTENUATION STATE (dB)
35
40
45
0
2
4
6
8
10
FREQUENCY (GHz)
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
8-2
HMC629LP4 / 629LP4E
v07.0410
3 dB LSB GaAs MMIC 4-BIT
DIGITAL ATTENUATOR, DC - 6 GHz
8
Step Error vs. Frequency
Normal Relative Phase vs. Frequency
(Only Major States are Shown)
100
1.5
1
0.5
0
-0.5
-1
BIT 24
40
20
0
-20
-40
-80
-100
4
6
8
10
(3, 6, 12) dB
-60
-2
2
45 dB
60
-1.5
0
24 dB
80
BIT (3, 6, 12)
ALL BITS
RELATIVE PHASE (deg)
STEP ERROR (dB)
ATTENUATORS - DIGITAL - SMT
2
0
1
FREQUENCY (GHz)
2
3
4
5
6
7
8
9
10
FREQUENCY (GHz)
Serial Control Interface
The HMC629LP4E contains a 3-wire SPI compatible digital interface (SERIN, CLK, LE). The serial control interface
is activated when P/S is kept high. The 6-bit serial word must be loaded MSB first. The positive-edge sensitive CLK
and LE requires clean transitions. If mechanical switches are used, sufficient debouncing should be provided. When
LE is high, 4-bit data in the serial input register is transferred to the attenuator. When LE is high CLK is masked to
prevent data transition during output loading.
When P/S is low, 3-wire SPI interface inputs (SERIN, CLK, LE) are disabled and the input register is loaded with
parallel digital inputs (D0-D5). When LE is high, 4-bit parallel data changes the state of the part per truth table.
For all modes of operations, the state will stay constant while LE is kept low.
8-3
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC629LP4 / 629LP4E
v07.0410
3 dB LSB GaAs MMIC 4-BIT
DIGITAL ATTENUATOR, DC - 6 GHz
Typ.
Min. serial period, tSCK
100 ns
Control set-up time, tCS
20 ns
Control hold-time, tCH
20 ns
LE setup-time, tLN
10 ns
Min. LE pulse width, tLEW
10 ns
Min LE pulse spacing, tLES
630 ns
Serial clock hold-time from LE, tCKN
10 ns
Hold Time, tPH.
0 ns
Latch Enable Minimum Width, tLEN
10 ns
Setup Time, tPS
2 ns
Parallel Mode (Direct Parallel Mode & Latched Parallel Mode)
Note: The parallel mode is enabled when P/S is set to low.
Direct Parallel Mode - The attenuation state is changed by the Control Voltage Inputs directly. The LE (Latch Enable)
must be at a logic high to control the attenuator in this manner.
Latched Parallel Mode - The attenuation state is selected using the Control Voltage Inputs and set while the LE is in
the Low state. The attenuator will not change state while LE is Low. Once all Control Voltage Inputs are at the desired
states the LE is pulsed. See timing diagram below for reference.
Power-Up States
If LE is set to logic LOW at power-up, the logic state of
PUP1 and PUP2 determines the power-up state of the
part per PUP truth table. If the LE is set to logic HIGH
at power-up, the logic state of D3-D0 determines
the power-up state of the part per truth table. The
attenuator latches in the desired power-up state
approximately 200 ms after power-up.
8
ATTENUATORS - DIGITAL - SMT
Timing Diagram (Latched Parallel Mode)
Parameter
PUP Truth Table
LE
PUP1
PUP2
Attenuation State
0
0
0
45 dB
0
1
0
45 dB
0
0
1
45 dB
0
1
1
Insertion Loss
1
X
X
0 to 45 dB
Note: Power-Up with LE= 1 provides direct parallel operation with
D0 - D3.
Power-On Sequence
The ideal power-up sequence is: GND, Vdd, digital
inputs, RF inputs. The relative order of the digital
inputs are not important as long as they are powered
after Vdd / GND
Bias Voltage
Vdd (Vdc)
Idd (Typ.) (mA)
5
2.0
Control Voltage Table
State
Vdd = +3V
Vdd = +5V
Low
0 to 0.5V @ <1 µA
0 to 0.8V @ <1 µA
High
2 to 3V @ <1 µA
2 to 5V @ <1 µA
Truth Table
Control Voltage Input
Attenuation State
D3
D2
D1
D0
High
High
High
High
Reference
I.L.
High
High
High
Low
3 dB
High
High
Low
High
6 dB
High
Low
High
High
12 dB
Low
High
High
High
24 dB
Any combination of the above states will provide an attenuation
approximately equal to the sum of the bits selected.
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
8-4
HMC629LP4 / 629LP4E
v07.0410
3 dB LSB GaAs MMIC 4-BIT
DIGITAL ATTENUATOR, DC - 6 GHz
ATTENUATORS - DIGITAL - SMT
8
Absolute Maximum Ratings
RF Input Power (DC - 6 GHz)
28 dBm (T = +85 °C)
Digital Inputs (Data, Shift Clock,
Latch Enable & Serial Input)
-0.5 to Vdd +0.5V
Bias Voltage (Vdd)
5.6V
Channel Temperature
150 °C
Continuous Pdiss (T = 85 °C)
(derate 10 mW/°C above 85 °C) [1]
0.66 W
Thermal Resistance
98.5 °C/W
Storage Temperature
-65 to +150 °C
Operating Temperature
-40 to +85 °C
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Outline Drawing
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS]
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE.
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST BE
SOLDERED TO PCB RF GROUND.
7. REFER TO PCB DESIGN AND ASSEMBLY FOR QFN PACKAGES
APPLICATION NOTE FOR SUGGESTED LAND PATTERN.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
HMC629LP4
Low Stress Injection Molded Plastic
Sn/Pb Solder
MSL1
[1]
HMC629LP4E
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL1
[2]
Package Marking [3]
H629
XXXX
H629
XXXX
[1] Max peak reflow temperature of 235 °C
[2] Max peak reflow temperature of 260 °C
[3] 4-Digit lot number XXXX
8-5
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC629LP4 / 629LP4E
v07.0410
3 dB LSB GaAs MMIC 4-BIT
DIGITAL ATTENUATOR, DC - 6 GHz
Pin Number
Function
Description
24
P/S
1
CLK
2
SERIN
3
LE
4, 15
GND
These pins and package bottom
must be connected to RF/DC ground.
5, 14
ATTIN,
ATTOUT
These pins are DC coupled and matched to 50 Ohms.
Blocking capacitors are required. Select value based
on lowest frequency of operation.
6 - 13
ACG1 - ACG6
External capacitors to ground are required. Select value for
lowest frequency of operation. Place capacitor as close to
pins as possible. See Application Circuit.
16
SEROUT
Serial input data delayed by 6 clock cycles.
17, 18
PUP2, PUP1
Interface Schematic
See truth table, control voltage
table and timing diagram.
ATTENUATORS - DIGITAL - SMT
8
Pin Descriptions
See truth table, control voltage
table and timing diagram.
20 - 23
D3, D2, D1, D0
19
Vdd
Supply voltage
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
8-6
HMC629LP4 / 629LP4E
v07.0410
3 dB LSB GaAs MMIC 4-BIT
DIGITAL ATTENUATOR, DC - 6 GHz
Application Circuit
ATTENUATORS - DIGITAL - SMT
8
8-7
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC629LP4 / 629LP4E
v07.0410
3 dB LSB GaAs MMIC 4-BIT
DIGITAL ATTENUATOR, DC - 6 GHz
8
ATTENUATORS - DIGITAL - SMT
Evaluation PCB
List of Materials for Evaluation PCB 118889 [1]
Item
Description
J1, J2
PCB Mount SMA Connector
J10, J12
DC Pin
J11
18 Pin DC Connector
C1 - C2
100 pF, capacitor 0402 pkg
C3
1000 pF, capacitor 0402 pkg
C4 - C8
330 pF, capacitor 0402 pkg
R1 - R10
100 kOhm Resistor, 0402 Pkg.
SW1
SPDT 4 Position DIP Switch
U1
HMC629LP4(E) Digital Attenuator
PCB [2]
118888 Evaluation PCB
The circuit board used in the application should use
RF circuit design techniques. Signal lines should
have 50 Ohm impedance while the package ground
leads and exposed paddle should be connected
directly to the ground plane similar to that shown.
A sufficient number of via holes should be used to
connect the top and bottom ground planes. The
evaluation circuit board shown is available from Hittite upon request.
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Arlon 25FR
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
8-8