HITTITE HMC675LP3E

HMC675LP3E
v00.1110
comparators - SMT
1
10 GHz LATCHED COMPARATOR
WITH RSCML OUTPUT STAGE
Typical Applications
Features
The HMC675LP3E is ideal for:
Propagation Delay: 100 ps
• ATE Applications
Overdrive & Slew Rate Dispersion: 10 ps
• High Speed Instrumentation
Minimum Pulse Width: 60 ps
• Digital Receiver Systems
Resistor Programmable Hysteresis
• Pulse Spectroscopy
Differential Latch Control
• High Speed Trigger Circuits
Active Gain: 43 dB
• Clock & Data Restoration
Power Dissipation: 100 mW
RSPECL and RSECL Versions Available
16 Lead 3x3mm SMT Package: 9mm2
Functional Diagram
General Description
The HMC675LP3E is a SiGe monolithic, ultra fast
comparator which features reduced swing CML output
drivers and latch inputs. The comparator supports 10
Gbps operation while providing 100 ps propagation
delay and 60 ps minimum pulse width with 0.2 ps rms
random jitter (RJ). Overdrive and slew rate dispersion
are typically 10 ps, making the device ideal for a
wide range of applications from ATE to broadband
communications. The reduced swing CML output stage
is designed to directly drive 400 mV into 50 Ohms
terminated to GND. The HMC675LP3E features high
speed latch and programmable hysteresis and may
be configured to operate in either latch mode, or as a
tracking comparator.
Electrical Specifications, TA = +25° C Vcci= +3.3 V, Vcco = 0 V, Vee = -3 V, VTERM = 0
Parameter
Conditions
Input Voltage Range
Input Differential Voltage
Typ.
Max
Units
-2
2
V
-1.75
1.75
V
Input Offset Voltage
±5
mV
Input Offset Voltage, Temperature Coefficient
15
µV / °C
Input Bias Current
15
uA
Input Bias Current Temperature Coefficient
50
nA / °C
Input Offset Current
4
µA
Input Impedance
50
Ω
Common Mode Input Impedance
350
KΩ
Differential Input Impedance
15
KΩ
Active Gain
43
dB
Common Mode Rejection Ratio
80
dB
±1
mV
Hysteresis
1-1
Min.
Rhys = ∞
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC675LP3E
v00.1110
10 GHz LATCHED COMPARATOR
WITH RSCML OUTPUT STAGE
Parameter
Conditions
Latch Enable Input Impedance
Min.
Typ.
Each Pin
8
Max
Units
KΩ
Latch to Output Delay, tPDOL , tPDOH
VOD = 200 mV
85
ps
Latch Minimum Pulse Width, tPL
VOD = 200 mV
20
ps
Latch Enable Input Range
VOD = 200 mV
Latch Setup Time, t s
VOD = 200 mV
1.6
Latch Hold Time, tH
2.4
V
45
ps
-42
ps
DC Output Characteristics, with 50 Ω to GND
Parameter
Conditions
Min.
Output Voltage High Level, Voh
-10
Output Voltage Low Level, Vol
-420
Output Voltage Differential Swing
Typ.
Max
Units
0
mV
-400
-380
mV
410
400
380
mV
Conditions
Min.
Typ.
Max
Units
VOD = 500 mV
70
100
130
AC Performance
Parameter
Propagation Delay - tPD, tPDL , tPDH
Propagation Delay, Temperature Coefficient
Propagation Delay Skew
(Rising to Falling Transition)
VOD Dispersion
Tpd vs. Common Mode Dispersion,
-1.75V <Vcm <1.75V
ps / °C
VOD - 500 mV
10
ps
50mV < VOD < 1 V
10
ps
VOD = 500 mV
3
ps
3.2
Equivalent Input Bandwidth [1]
Deterministic Jitter (pp)
ps
0.45
Noise (RTI)
8.5
10
nV/√(Hz) RTI
10.5
GHz
Deterministic Jitter at 10 Gbps
with ±100mV Overdrive
2
ps
Random Jitter at 10 Gbps
with ±100mV Overdrive
0.2
ps rms
Random Jitter (rms)
Minimum Pulse Width
comparators - SMT
1
Latch Enable Characteristics
60
ps
Q / QB Rise Time
From 20% to 80%
27
ps
Q / QB Fall Time
From 20% to 80%
18
ps
Power Supply Requirements
Parameter
Conditions
Min.
Typ.
Max
Units
Input Supply Current, Icci
9
mA
Output Supply Current, Icco
8
mA
Vee Current, lee
24
mA
Power Dissipation, Pd
100
mW
PSRR, Vcci
35
dB
PSRR, Vee
35
dB
Note 1: Equivalent Input Bandwidth is calculated with the following formula: Bweq=0.22/√ (TRCOMP2 -TRIN 2) where TRIN is the 20%/80%
transition time of a quasi-Gaussian signal applied to the comparator input, and TRCOMP is the effective transition time digitized by the
comparator.
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
1-2
HMC675LP3E
v00.1110
Dispersion vs. Overdrive Voltage
Propagation Delay vs. Common Mode[1]
11
15
12.5
9
10
Rising Edge
Falling Edge
7
ΔtPD
DISPERSION (ps)
comparators - SMT
1
10 GHz LATCHED COMPARATOR
WITH RSCML OUTPUT STAGE
5
Rising Edge
Falling Edge
7.5
5
2.5
3
0
1
-2.5
-5
-1
0
10
20
30
40
50
60
70
80
90
100
-2
OVERDRIVE VOLTAGE (mV)
-0.5
0
0.5
1
1.5
2
Comparator Hysteresis
vs. Rhys Control Resistor
0.1
20
0
16
HYSTERESIS (mV)
-0.1
VOLTAGE (V)
-1
COMMON MODE VOLTAGE (mV)
Output Voltage vs. Temperature
VOH
VOL
-0.2
-0.3
-0.4
12
8
4
-0.5
-0.6
-45
-1.5
0
-32
-19
-6
7
20
33
46
59
72
85
10
100
1000
10000
RESISTANCE (Ohm)
TEMPERATURE (C)
Eye Diagram
[1] Vcci = 3.3V, Vcc0 = 0, Vee = -3V, VTERM = 0
1-3
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC675LP3E
v00.1110
10 GHz LATCHED COMPARATOR
WITH RSCML OUTPUT STAGE
1
comparators - SMT
Timing Diagram
Timing Descriptions
Symbol
Timing
Description
tPDH
Input to output high delay
Propagation delay measured from the time the input signal crosses the reference
(± the input offset voltage) to the 50% point of an output low-to-high transition.
tPDL
Input to output low delay
Propagation delay measured from the time the input signal crosses the reference
(± the input offset voltage) to the 50% point of an output high-to-low transition.
tPLDH
Latch enable to output high delay
Propagation delay measured from the 50% point of the latch enable signal low-to-high
transition to the 50% point of an output low-to-high transition.
tPLDL
Latch enable to output low delay
Propagation delay measured from the 50% point of the latch enable signal low-to-high
transition to the 50% point of an output high-to-low transition.
tH
Minimum hold time
Minimum time after the negative transition of the latch enable signal that the input
signal must remain unchanged to be acquired and held at the outputs.
tPL
Minimum latch enable pulse width
Minimum time that the latch enable signal must be high to acquire an input signal
change.
tS
Minimum setup time
Minimum time before the negative transition of the latch enable signal that an input
signal change must be present to be acquired and held at the outputs.
tR
Output rise time
Amount of time required to transition from a low to a high output as measured at the
20% and 80% points.
tr
Output fall time
Amount of time required to transition from a high to a low output as measured at the
20% and 80% points.
Voltage overdrive
Difference between the input voltages VA and VB-
VOD
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
1-4
HMC675LP3E
v00.1110
comparators - SMT
1
10 GHz LATCHED COMPARATOR
WITH RSCML OUTPUT STAGE
Absolute Maximum Ratings
Input Supply Voltage (Vcci to GND)
-0.5V to +4V
Output Supply Voltage (Vcco to GND)
-0.5V to +4V
Positive Supply Differential (Vcci - Vcco)
-0.5V to +3V
Input Voltage
-2V to +2V
Differential Input Voltage
-2V to +2V
Input Voltage, Latch Enable
-0.5V to Vcci +0.5V
Applied Voltage (HYS)
Vee to GND
Maximum Input Current
±1 mA
Output Current
20 mA
Junction Temperature
125°C
Continuous Pdiss (T = 85°C)
(Derate 43.5 mW/°C above 85°C)
1.74 W
Thermal Resistance (Rth) (Junction to Lead)
23 °C/W
Storage Temperature
-65°C to +150°C
Operating Temperature
-40°C to +85°C
ESD Sensitivity (HBM)
Class 1A
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Outline Drawing
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS]
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST BE
SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED
LAND PATTERN.
Package Information
Part Number
Package Body Material
Lead Finish
HMC675LP3E
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL Rating
MSL1
[1]
Package Marking [2]
H675
XXXX
[1] Max peak reflow temperature of 260 °C
[2] 4-Digit lot number XXXX
1-5
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC675LP3E
v00.1110
10 GHz LATCHED COMPARATOR
WITH RSCML OUTPUT STAGE
Pin Number
Function
Description
1
VTP
Termination resistor return pin for Vp Input.
2
INP
Non-Inverting analog input
3
INN
Inverting analog input
4
VTN
Termination resistor return pin for Vn input
5, 16
Vcci
Positive supply voltage input stage.
6
LE
Latch enable bar input pin, inverting side.
7
LE
Latch enable bar input pin, non-inverting side.
8
N/C
Pin is not connected inside the package.
Connect package pin to GND for improved noise.
9, 12
Vcco
Positive supply voltage for the output stage.
Q
Inverting output. Q bar is at logic low if the analog voltage
at the non-inverting input, INP, is greater than the analog
voltage at the inverting input, INN, provided that the
comparator is in compare mode. Refer to the LE/LE bar
descriptions (pins 6, 7) for more information.
Q
Non-inverting output. Q is at logic high if the analog voltage
at the non-inverting input, INP, is greater than the analog
voltage at the inverting input, INN, provided that the
comparator is in compare mode. Refer to the LE/LE bar
descriptions (pins 6, 7) for more information.
14
HYS
Hysteresis Control pin. This pin should be left disconnected
for zero hysteresis. Connect to Vee with a resistor to add
the desired amount of hysteresis. Refer to Figure on page
6-34. to determine the correct sizing of Rhys hysteresis
control resistor.
13
Vee
Negative power supply, -3V.
15
RTN
Return for ESD protection.
Package Base
Exposed paddle must be connected to Vee.
10
11
Interface Schematic
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
comparators - SMT
1
Pin Descriptions
1-6
HMC675LP3E
v00.1110
comparators - SMT
1
10 GHz LATCHED COMPARATOR
WITH RSCML OUTPUT STAGE
Evaluation PCB
Front Side
Back Side
1-7
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC675LP3E
List of Materials for Evaluation PCB 125932
Item
Description
J1
8 Pos. Vertical TIN
J2 - J7
2.92 mm 40 GHz Jack
J8
Terminal Strip, Single Row 3 Pin SMT
JP1, JP2
2 Pos. Vertical TIN
C1 - C3, C5, C6,
C8 - C10
100 pF Capacitor, 0402 Pkg.
C4, C7, C11
330 pF Capacitor, 0402 Pkg.
C11 - C13
4.7 µF Tantalum
TP1 - TP4
DC Pin, Swage Mount
U1
HMC675LP3E Comparator
PCB
125929 Evaluation PCB
10 GHz LATCHED COMPARATOR
WITH RSCML OUTPUT STAGE
[1]
The circuit board used in the application should
use RF circuit design techniques. Signal lines
should have 50 Ohm impedance while the package ground leads should be connected directly to
the ground plane similar to that shown. A sufficient
number of via holes should be used to connect the
top and bottom ground planes in order to provide
good RF grounding to 25 GHz. The evaluation
circuit board shown is available from Hittite upon
request.
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350 or Arlon 25FR
1
comparators - SMT
v00.1110
Application Circuit
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
1-8