HMC801LP3E v01.0610 15 dB GaAs MMIC 1-BIT DIGITAL POSITIVE CONTROL ATTENUATOR, DC - 10 GHz Attenuators - DIGITAL - SMT 5 Typical Applications Features The HMC801LP3E is ideal for both RF and IF applications: ± 0.4 dB Typical Step Error • Test Equipment and Sensors High IP3: +53 dBm • ISM, MMDS, WLAN, WiMAX, WiBro Single Control Line • Microwave Radio & VSAT TTL/CMOS Compatible Control • Cellular Infrastructure Single +5V Supply Low Insertion Loss: 2 dB 16 Lead 3x3 mm SMT Package: 9 mm² Functional Diagram General Description The HMC801LP3E is a broadband bidirectional 1-bit GaAs IC digital attenuator in a low cost leadless surface mount package. This single positive control line digital attenuator utilizes off chip AC ground capacitors for near DC operation, making it suitable for a wide variety of RF and IF applications. Covering DC to 10 GHz, the insertion loss is less than 2 dB typical and attenuation accuracy is excellent at ±0.4 dB typical step error. The attenuator also features a high IIP3 of +53 dBm. One TTL/CMOS control input is used to select the attenuation state and a single Vdd bias of +5V is required. Electrical Specifications, TA = +25° C, With Vdd = +5V & Vctl = 0/+5V Parameter Frequency (GHz) Min. Typ. Max. Units 2.0 3.0 3.5 dB dB dB Insertion Loss DC - 4 GHz 4 - 8 GHz 8 - 10 GHz 1.0 2.0 2.5 Attenuation Range DC - 10 GHz 15 dB Return Loss (RF1 & RF2, Both States) DC - 6 GHz 6 - 10 GHz 18 14 dB dB Attenuation Accuracy: (Referenced to Insertion Loss) DC - 8 GHz 8 - 10 GHz ± 0.4 ± 0.5 Input Power for 0.1 dB Compression DC - 0.4 GHz 0.4 - 10 GHz 20 30* dBm dBm Input Third Order Intercept Point (Two-Tone Input Power= 0 dBm Each Tone) DC - 0.4 GHz 0.4 - 10 GHz 43 53 dBm DC - 10 GHz 120 150 ns ns ± 0.6 ± 0.7 dB dB Switching Characteristics tRISE, tFALL (10/90% RF) tON, tOFF (50% CTL to 10/90% RF) * For frequencies greater than 0.4 GHz, the 0.1 dB compression point is greater than the absolute maximum RF input power of 30 dBm. 5-1 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC801LP3E v01.0610 15 dB GaAs MMIC 1-BIT DIGITAL POSITIVE CONTROL ATTENUATOR, DC - 10 GHz Insertion Loss RETURN LOSS (dB) INSERTION LOSS (dB) -1 -2 +25 C +85 C -40 C -3 -4 INSERTION LOSS 15 dB -10 -20 -30 -40 -5 0 2 4 6 8 10 0 12 2 4 6 8 10 12 10 12 10 12 FREQUENCY (GHz) FREQUENCY (GHz) Relative Attenuation Output Return Loss -9 NORMALIZED ATTENUATION (dB) 0 -10 -20 -30 INSERTION LOSS 15 dB -40 -11 -13 -15 Attenuators - DIGITAL - SMT 0 0 RETURN LOSS (dB) 5 Input Return Loss -17 -19 -21 0 2 4 6 8 10 12 0 2 FREQUENCY (GHz) 4 6 8 FREQUENCY (GHz) Bit Error vs. Frequency Relative Phase vs. Frequency 1.2 50 0.8 30 20 BIT ERROR (dB) RELATIVE PHASE (dB) 40 10 0 -10 -20 -30 0.4 0 -0.4 -0.8 -40 -1.2 -50 0 2 4 6 8 FREQUENCY (GHz) 10 12 0 2 4 6 8 FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 5-2 HMC801LP3E v01.0610 15 dB GaAs MMIC 1-BIT DIGITAL POSITIVE CONTROL ATTENUATOR, DC - 10 GHz Input IP3 vs. Frequency (Low Frequency Detail) 70 70 60 60 50 50 IP3 (dBm) IP3 (dBm) Input IP3 vs. Frequency INSERTION LOSS 15 dB 40 30 INSERTION LOSS 15 dB 40 30 20 20 0 2 4 6 8 10 12 0 0.1 0.2 FREQUENCY (GHz) 0.3 0.4 FREQUENCY (GHz) Input Power for 0.1 dB Compression* Truth Table (Low Frequency Detail) P0.1dB INPUT POWER (dBm) Attenuators - DIGITAL - SMT 5 40 Control Voltage Input 35 V1 Attenuation State RF1 - RF2 30 High Reference Insertion Loss 25 Low 15 dB 20 15 Bias Voltage & Current 10 Vdd = +5 Vdc ± 10% 5 0 0 0.1 0.2 0.3 0.4 0.5 Vdd (Vdc) Idd (Typ.) (mA) 4.5 0.21 5.0 0.23 5.5 0.25 FREQUENCY (GHz) Control Voltage State Bias Condition Low 0 to +0.8V @ -1 µA Typ. High +2 to +5V @ 30 µA Typ. Note: Vdd = +5V * For frequencies greater than 0.4 GHz, the 0.1 dB compression point is greater than the absolute maximum RF input power of 30 dBm. 5-3 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 0.5 HMC801LP3E v01.0610 15 dB GaAs MMIC 1-BIT DIGITAL POSITIVE CONTROL ATTENUATOR, DC - 10 GHz RF Input Power (DC - 10 GHz) +30 dBm Control Voltage Range (V1) -1 to Vdd +1V Bias Voltage (Vdd) +7 Vdc Channel Temperature 150 °C Continuous Pdiss (T = 85 °C) (derate 12 mW/°C above 85 °C) 0.783 W Thermal Resistance (channel to ground paddle) 83 °C/W Storage Temperature -65 to +150 °C Operating Temperature -40 to +85 °C ESD Sensitivity (HBM) Class 1A ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing Attenuators - DIGITAL - SMT 5 Absolute Maximum Ratings NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Package Information Part Number Package Body Material Lead Finish HMC801LP3E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL Rating MSL1 [1] Package Marking [2] H801 XXXX [1] Max peak reflow temperature of 260 °C [2] 4-Digit lot number XXXX For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 5-4 HMC801LP3E v01.0610 15 dB GaAs MMIC 1-BIT DIGITAL POSITIVE CONTROL ATTENUATOR, DC - 10 GHz Attenuators - DIGITAL - SMT 5 Pin Descriptions Pin Number Function Description 1 Vdd Supply Voltage. 2, 4, 9, 11 GND These pins and the exposed ground paddle must be connected to RF/DC ground. 3, 10 RF1, RF2 These pins are DC coupled and matched to 50 Ohms. Blocking capacitors are required. Select value based on lowest frequency of operation. 5, 8 ACG1, ACG2 External capacitor to ground is required. Select value for lowest frequency of operation. Place capacitor as close to pins as possible. 6, 7, 12, 13, 15, 16 N/C The pins are not connected internally; however, all data shown herein was measured with these pins connected to RF/DC ground externally. 14 V1 See truth table and control voltage table. Interface Schematic Application Circuit 5-5 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC801LP3E v01.0610 15 dB GaAs MMIC 1-BIT DIGITAL POSITIVE CONTROL ATTENUATOR, DC - 10 GHz 5 Attenuators - DIGITAL - SMT Evaluation PCB List of Materials for Evaluation PCB 126894 [1] Item Description J1, J2 PCB Mount SMA Connector J3, J4 DC Connector C1 1000 pF Capacitor, 0603 Pkg. C2, C3 100 pF Capacitor, 0402 Pkg. C4, C5 330 pF Capacitor, 0402 Pkg. U1 HMC801LP3E Digital Attenuator PCB [2] 121213 Evaluation PCB [1] Reference this number when ordering complete evaluation PCB The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. [2] Circuit Board Material: Rogers 4350 or Arlon 25FR For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 5-6