HMC820LP6CE v05.1010 FRACTIONAL-N SYNTHESIZER w/ INTEGRATED VCO 1095 - 1275, 2190 - 2550, 4380 - 5100 MHz Features • RF Bandwidth: 1095-1275, 2190-2550, 4380-5100 MHz • 24-bit Step Size, Resolution 3 Hz typ • Ultra Low Phase Noise -105 dBc/Hz in Band Typ. • Built in Digital Self Test • Figure of Merit (FOM) -227 dBc/Hz • Exact Frequency Mode • 40 Lead 6x6 mm SMT Package: 36 mm2 • <180 fs RMS Jitter Typical Applications PLLS w/ INTEGRATED VCO - SMT 7 7-1 • Cellular/4G Infrastructure • Phased Array Applications • Repeaters and Femtocells • DDS Replacement • Communications Test Equipment • Very High Data Rate Radios • CATV Equipment Functional Diagram For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC820LP6CE v05.1010 FRACTIONAL-N SYNTHESIZER w/ INTEGRATED VCO 1095 - 1275, 2190 - 2550, 4380 - 5100 MHz General Description The HMC820LP6CE is a fully functioned Fractional-N Phase-Locked-Loop (PLL) Frequency Synthesizer with an Integrated Voltage Controlled Oscillator (VCO). The synthesizer consists of an integrated low noise VCO with a triband output, an autocalibration subsystem for low voltage VCO tuning, a very low noise digital Phase Detector (PD), a precision controlled charge pump, a low noise reference path divider and a fractional divider. The fractional synthesizer features an advanced delta-sigma modulator design that allows both ultra-fine step sizes and low spurious products. The phase detector (PD) features cycle slip prevention (CSP) technology to allow faster frequency hopping times. Ultra low in-close phase noise and low spurious also allows wider loop bandwidths for faster frequency hopping and low micro-phonics. Electrical Specifications, TA = +25° C VPPCP, VDDCP, VCC1, VCC2 = 5V ±4%; RVDD, AVDD, DVDD3V, VCCPD, VCCHF, VCCPS = 3.3V ±6% GNDCP = GNDLS = Ground Paddle = 0V Parameter Condition Min. Typ. Max. Units RF Output Characteristics VCO Frequency at PLL Input 4380 5100 MHz RF Output Frequency at f VCO/2 1095 1275 MHz RF Output Frequency at f VCO 2190 2550 MHz RF Output Frequency at 2f VCO 4380 5100 MHz RF Output Power at f VCO/2 RF Output Power at f VCO RF Output Power at 2f VCO 7.5 10 12.5 dBm 3 6.5 10 dBm -9 -4 1 dBm VCO Tuning Sensitivity Measured at fo, 2V 12 16 24 MHz/V VCO Supply Pushing Measured at fo, 2V -2 RF Output fo/2 Harmonic Doubler Mode RF Output 3fo/2 Harmonic Doubler Mode RF Output 2nd Harmonic fo/2/fo/2fo RF Output 5fo/2 Harmonic Doubler Mode RF Output 3rd Harmonic RF Output 7fo/2 Harmonic RF Output 4th Harmonic 1.5 MHz/V -22 -18 dBc -50 -41 dBc -25 / -30 / -42 -20 / -19 / -36 -60 fo/2/fo/2fo -56 -27 / -40 / -60 -24 / -30 / -51 Doubler Mode -65 fo/2/fo/2fo -61 -30 / -50 / -68 -25 / -42 / -62 dBc dBc dBc dBc dBc RF Divider Characteristics 19-Bit N-Divider Range (Integer) 19-Bit N-Divider Range (Fractional) Max = 219 - 1 524,287 Fractional nominal divide ratio varies (-3 / +4) dynamically max 524,283 7 PLLS w/ INTEGRATED VCO - SMT For theory of operation and register map refer to the “PLLs w/ Integrated VCOs - RF VCOs Operating Guide”. To view the Operating Guide, please visit www.hittite.com and choose HMC820LP6CE from the “Search by Part Number” pull down menu. REF Input Characteristics Max Ref Input Frequency Ref Input Range Synthesizer phase noise can degrade by about 5 dB when operating with a reference frequency near the low end of this range. 10 50 200 MHz AC Coupled 1 2 3.3 Vp-p 5 pF Ref Input Capacitance 14-Bit R-Divider Range 1 16,383 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 7-2 HMC820LP6CE v05.1010 FRACTIONAL-N SYNTHESIZER w/ INTEGRATED VCO 1095 - 1275, 2190 - 2550, 4380 - 5100 MHz Electrical Specifications (Continued) Parameter Condition Min. [1] Typ. Max. Units Phase Detector (PD) PD Frequency Fractional Feedback Mode 0.1 100 MHz PD Frequency Fractional Feedforward Mode (and Register 6 [17:16] = 10) 0.1 80 MHz PD Frequency Integer Mode 0.1 125 MHz 2.54 mA Charge Pump Output Current 0.02 Charge Pump Gain Step Size PD/Charge Pump SSB Phase Noise PLLS w/ INTEGRATED VCO - SMT 7 20 µA 50 MHz Ref, Input Referred 1 kHz -141 dBc/Hz 10 kHz Add 1 dB for Fractional -149 dBc/Hz 100 kHz Add 3 dB for Fractional -153 dBc/Hz Logic Inputs VIH Input High Voltage DVDD3V-0.4 DVDD3V V VIL Input Low Voltage 0 0.4 V VOH Output High Voltage DVDD3V-0.4 DVDD3V V VOL Output Low Voltage 0 0.4 V 3.5 V Logic Outputs Power Supply Voltages Analog 3.3V Supplies Digital Supply Analog 5V Supplies AVDD, VCCHF, VCCPS, VCCPD, RVDD 3.0 3.3 DVDD3V 3.0 3.3 3.5 V VPPCP, VDDCP, VCC1, VCC2 4.8 5 5.2 V Power Supply Currents +5V Analog Charge Pump VPPCP, VDDCP 5.3 mA +5V VCO Core and PLL Buffer VCC2 56 mA +5V VCO Divider and RF Buffer VCC1 36 mA AVDD, VCCHF, VCCPS, VCCPD, RVDD 45 mA +3.3V Analog +3.3V Digital Power Down - Crystal Off Power Down - Crystal On, 100 MHz DVDD3V 6.5 mA Reg 01h=0, Crystal Not Clocked 10 µA Reg 01h=0, Crystal Clocked 100 MHz 10 200 µA Power on Reset Typical Reset Voltage on DVDD Min DVDD Voltage for No Reset Power on Reset Delay 700 mV 250 µs 1.5 V Note 1: This maximum phase detector frequency can only be achieved if the minimum N value is respected. eg. In the case of fractional feedback mode, the maximum PFD rate = fvco/20 or 100 MHz, whichever is less. 7-3 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC820LP6CE v05.1010 FRACTIONAL-N SYNTHESIZER w/ INTEGRATED VCO 1095 - 1275, 2190 - 2550, 4380 - 5100 MHz Electrical Specifications (Continued) Parameter Condition Min. Typ. Max. Units VCO Open Loop Phase Noise at fo/2 10 kHz Offset -93 -87 dBc/Hz 100 kHz Offset -122 -119 dBc/Hz 1 MHz Offset -147 -144 dBc/Hz 10 MHz Offset -162 dBc/Hz 100 MHz Offset -163 dBc/Hz VCO Open Loop Phase Noise at fo 10 kHz Offset -87 -81 dBc/Hz 100 kHz Offset -116 -116 dBc/Hz 1 MHz Offset -141 -138 dBc/Hz 10 MHz Offset -161 dBc/Hz 100 MHz Offset -166 dBc/Hz 7 10 kHz Offset -81 -75 dBc/Hz 100 kHz Offset -110 -110 dBc/Hz 1 MHz Offset -135 -132 dBc/Hz 10 MHz Offset -155 dBc/Hz 100 MHz Offset -155 dBc/Hz Closed Loop Phase Noise PLL + VCO at fvco/2 Integer, 25 MHz PD 1 kHz Offset -113 dBc/Hz Integer, 25 MHz PD 10 kHz Offset -118 dBc/Hz Integer, 25 MHz PD 100 kHz Offset -118 dBc/Hz 1 kHz Offset -108 dBc/Hz Fractional, 25 MHz PD 10 kHz Offset -113 dBc/Hz Fractional, 25 MHz PD 100 kHz Offset -114 dBc/Hz Integer, 25 MHz PD 1 kHz Offset -107 dBc/Hz Integer, 25 MHz PD 10 kHz Offset -112 dBc/Hz Integer, 25 MHz PD 100 kHz Offset -112 dBc/Hz 1 kHz Offset -102 dBc/Hz Fractional, 25 MHz PD Closed Loop Phase Noise PLL + VCO at fvco Fractional, 25 MHz PD Fractional, 25 MHz PD 10 kHz Offset -107 dBc/Hz Fractional, 25 MHz PD 100 kHz Offset -108 dBc/Hz 1 kHz Offset -101 dBc/Hz Integer, 25 MHz PD 10 kHz Offset -106 dBc/Hz Integer, 25 MHz PD 100 kHz Offset -106 dBc/Hz Fractional, 25 MHz PD 1 kHz Offset -96 dBc/Hz Fractional, 25 MHz PD 10 kHz Offset -101 dBc/Hz 100 kHz Offset -102 dBc/Hz Closed Loop Phase Noise PLL + VCO at 2fo Integer, 25 MHz PD Fractional, 25 MHz PD Figure of Merit PLLS w/ INTEGRATED VCO - SMT VCO Open Loop Phase Noise at 2fo Normalized 1 Hz Integer Mode Measured w/ 50 MHz PD at 30 kHz Offset -229 dBc/Hz Fractional Mode Measured w/ 50 MHz PD at 30 kHz Offset -227 dBc/Hz For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 7-4 HMC820LP6CE v05.1010 FRACTIONAL-N SYNTHESIZER w/ INTEGRATED VCO 1095 - 1275, 2190 - 2550, 4380 - 5100 MHz Typical Closed Loop Fractional Phase Noise [1] Closed Loop Integer Phase Noise -80 -90 -90 -100 -100 PHASE NOISE (dBc/Hz) PHASE NOISE (dBc/Hz) -80 -110 -120 -130 -140 1095 MHz FF 2190 MHz FF 4380 MHz FF -150 -160 -170 -180 2 10 -120 -130 -140 1096 MHz FF 2192 MHz FF 4384 MHz FF -150 -160 -170 10 3 10 4 10 5 10 6 10 7 10 -180 2 10 8 10 3 10 OFFSET FREQUENCY (Hz) 7 5 10 6 10 7 10 8 1100 -60 fmax 1095 MHz FF 2190 MHz FF 4380 MHz FF -80 n0 1050 -100 kvco (MHz/V) PHASE NOISE (dBc/Hz) 10 Typical Tuning Curves vs. Switch Position -40 -120 -140 fmax 1000 950 fmin -160 -180 3 10 900 10 4 10 5 10 6 10 7 10 8 0 1 n2 n4 n6 n8 n10 n12 n14 n16 n18 n20 n22 n24 n26 n30 2 3 n31 4 5 TUNING VOLTAGE (V) OFFSET FREQUENCY (Hz) Free Running VCO Phase Noise Over Temperature Typical VCO Tuning Voltage After Calibration -100 5 TUNE VOLTAGE AFTER CALIBRATION (V) 100 kHz Offset -110 -120 +27C +85C -40C -130 1 MHz Offset -140 -150 10 MHz Offset -160 -170 2150 4 OFFSET FREQUENCY (Hz) Free Running Phase Noise PHASE NOISE (dBc/Hz) PLLS w/ INTEGRATED VCO - SMT -110 2206 2263 2319 2375 2431 FREQUENCY (MHz) 2487 2544 4 fmin 3 31 fmax 15 0 2 1 0 2600 VCO FREQUENCY [1] Fractional Mode, 50 MHz Crystal, R=1, ~80 kHz Loop BW, (Loop filter values: Contact factory for component values) 2mA Charge Pump, -385µA Offset. 7-5 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC820LP6CE v05.1010 FRACTIONAL-N SYNTHESIZER w/ INTEGRATED VCO 1095 - 1275, 2190 - 2550, 4380 - 5100 MHz Typical VCO Sensitivity vs. Cap @ Fo Voltage Typical Output Power - Narrow Band Match 60 20 TUNING CAP 31, 2160 MHz AT 2V TUNING CAP 15, 2350 MHz AT 2V TUNING CAP 0, 2604 MHz AT 2V 15 OUTPUT POWER (dBm) 40 30 Typical Operating Range 20 10 0 Divide-by-2 10 Fundamental -40C 5 Doubler 27C 0 85C -5 -10 0 1 2 3 4 -15 1000 5 TUNING VOLTAGE (V) 2000 3000 4000 5000 6000 OUTPUT FREQUENCY (MHz) Figure of Merit NORMALIZED PHASE NOISE (dBc/Hz) -200 -210 Typ FOM vs Offset -220 FOM Floor FOM 1/f Noise -230 -240 2 10 10 3 10 4 10 5 10 6 FREQUENCY OFFSET (Hz) For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 7 PLLS w/ INTEGRATED VCO - SMT kvco (MHz/V) 50 7-6 HMC820LP6CE v05.1010 FRACTIONAL-N SYNTHESIZER w/ INTEGRATED VCO 1095 - 1275, 2190 - 2550, 4380 - 5100 MHz Pin Descriptions PLLS w/ INTEGRATED VCO - SMT 7 7-7 Pin Number Function Description 1 AVDD DC Power Supply for analog circuitry. 2, 5, 6, 8, 9, 11 - 14, 18 - 22, 24, 26, 34, 37, 38 N/C The pins are not connected internally; however, all data shown herein was measured with these pins connected to RF/DC ground externally. 3 VPPCP Power Supply for charge pump analog section 4 CP Charge Pump Output 7 VDDCP Power Supply for the charge pump digital section 10 RVDD Reference Supply 15 XREFP Reference Oscillator Input 16 DVDD3V DC Power Supply for Digital (CMOS) Circuitry 17 CEN Chip Enable. Connect to logic high for normal operation. 23 VTUNE VCO Varactor. Tuning Port Input. 25 VCC2 VCO Analog Supply 2 27 VCC1 VCO Analog Supply 1 28 RF_N [1] RF Positive Output 29 [1] 30 RF_P SEN RF Negative Output PLL Serial Port Enable (CMOS) Logic Input 31 SDI PLL Serial Port Data (CMOS) Logic Input 32 SCK PLL Serial Port Clock (CMOS) Logic Input 33 LD_SDO Lock Detect, or Serial Data, or General Purpose (CMOS) Logic Output (GPO) 35 VCCHF DC Power Supply for Analog Circuitry 36 VCCPS DC Power Supply for Analog Prescaler 39 VCCPD DC Power Supply for Phase Detector 40 BIAS External bypass decoupling for precision bias circuits. Note: 1.920V ±20mV reference voltage (BIAS) is generated internally and cannot drive an external load. Must be measured with 10GΩ meter such as Agilent 34410A, normal 10MΩ DVM will read erroneously. [1] For doubler mode of operation, pin 28 (RF_N) and pin 29 (RF_P) outputs must be shorted together. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC820LP6CE v05.1010 FRACTIONAL-N SYNTHESIZER w/ INTEGRATED VCO 1095 - 1275, 2190 - 2550, 4380 - 5100 MHz Absolute Maximum Ratings AVDD, RVDD, DVDD3V, VCCPD, VCCHF, VCCPS -0.3V to +3.6V VPPCP, VDDCP, VCC1 -0.3V to +5.8V VCC2 -0.3V to +5.5V Operating Temperature -40°C to +85°C Storage Temperature -65°C to 125°C Maximum Junction Temperature 125 °C Thermal Resistance (RTH) (junction to ground paddle) 20 °C/W Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Reflow Soldering Peak Temperature 260°C Time at Peak Temperature 40 sec ESD Sensitivity (HBM) 7 Class 1B PLLS w/ INTEGRATED VCO - SMT Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED PCB LAND PATTERN. Package Information Part Number Package Body Material Lead Finish MSL Rating Package Marking [1] HMC820LP6CE RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 H820 XXXX [1] 4-Digit lot number XXXX For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 7-8 HMC820LP6CE v05.1010 FRACTIONAL-N SYNTHESIZER w/ INTEGRATED VCO 1095 - 1275, 2190 - 2550, 4380 - 5100 MHz Evaluation PCB, fo & fo/2 Modes PLLS w/ INTEGRATED VCO - SMT 7 7-9 The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. Evaluation PCB Schematic To view this Evaluation PCB Schematic please visit www.hittite.com and choose HMC820LP6CE from the “Search by Part Number” pull down menu to view the product splash page. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC820LP6CE v05.1010 FRACTIONAL-N SYNTHESIZER w/ INTEGRATED VCO 1095 - 1275, 2190 - 2550, 4380 - 5100 MHz List of Materials for Evaluation PCB 127825, fo & fo/2 Mode [1] Description J1, J2 PCB Mount SMA RF Connector J3 Dual Row Terminal Strip J4 - J6 Connector Header C1, C15 - C17, C25 10 µF Capacitor, 0805 Pkg. C2, C3, C6, C7, C11, C12, C14, C18, C27, C43, C45 0.47 µF Capacitor, 0402 Pkg. C4, C13 22 pF Capacitor, 0402 Pkg. C5, C33 1000 pF Capacitor, 0402 Pkg. C8 1.5 pF Capacitor, 0402 Pkg. C19 - C24, C28, C30, C32, C34 0.1 µF Capacitor, 0402 Pkg. C26 1 µF Capacitor, 0603 Pkg. C29 47 pF Capacitor, 0402 Pkg. C35 3300 pF Capacitor, 0402 Pkg. C36 270 pF Capacitor, 0402 Pkg. C37, C38 68 pF Capacitor, 0402 Pkg. C39 - C42, C44 4.7 µF Tantalum Capacitor, 0805 Pkg R1, R2, R5, R8, R11, R15, R18, R19, R21, R24 0 Ohm Resistor, 0402 Pkg. R3, R4 1 Ohm Resistor, 0402 Pkg. R6, R7 0 Ohm Resistor, 0805 Pkg. R12, R20, R29 51 Ohm Resistor, 0402 Pkg. R22, R25 20 kOhm Resistor, 0402 Pkg. R26 - R28 1k Ohm Resistor, 0402 Pkg. L1 3.9 nH Inductor, 0402 Pkg. L2, L3 47 nH Inductor, 0402 Pkg. TP3, TP4 Test Point PC Compact SMT U1 HMC820LP6CE PLL with Integrated VCO U2 HMC860LP3E Low Noise Quad Linear Regulator Y1 3.3V, 50 MHz VCXO Crystal Oscillator PCB [2] 125998 Evaluation Board [1] Reference this number when ordering complete evaluation PCB For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 7 PLLS w/ INTEGRATED VCO - SMT Item 7 - 10 HMC820LP6CE v04.0410 FRACTIONAL-N SYNTHESIZER w/ INTEGRATED VCO 1095 - 1275, 2190 - 2550, 4380 - 5100 MHz Evaluation PCB, 2xfo Mode PLLS w/ INTEGRATED VCO - SMT 7 7 - 11 The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. Evaluation PCB Schematic To view this Evaluation PCB Schematic please visit www.hittite.com and choose HMC820LP6CE from the “Search by Part Number” pull down menu to view the product splash page. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC820LP6CE v04.0410 FRACTIONAL-N SYNTHESIZER w/ INTEGRATED VCO 1095 - 1275, 2190 - 2550, 4380 - 5100 MHz List of Materials for Evaluation PCB 128157, 2xfo Mode [1] Description J1, J2 PCB Mount SMA RF Connector J3 Dual Row Terminal Strip J4 - J6 Connector Header C1, C15 - C17, C25 10 uF Capacitor, 0805 Pkg. C2, C3, C6, C7, C11, C12, C14, C18, C27, C43, C45 0.47 uF Capacitor, 0402 Pkg. C4, C13 22 pF Capacitor, 0402 Pkg. C5, C33 0.001 uF Capacitor, 0402 Pkg. C8 1.8 pF Capacitor, 0402 Pkg. C19, C20 - C24, C28, C30, C32, C34 0.1 uF Capacitor, 0402 Pkg. C26 1 uF Capacitor, 0603 Pkg. C31 0.5 pF Capacitor, 0402 Pkg. C35 0.0033 uF Capacitor, 0402 Pkg. C36 270 pF Capacitor, 0402 Pkg. C37, C38 68 pF Capacitor, 0402 Pkg. C39 - C42, C44 4.7 uF Capacitor, 0805 Pkg. C46 27 pF Capacitor, 0402 Pkg. C47 47 pF Capacitor, 0402 Pkg. R1, R2, R8, R11, R15, R18, R19, R21, R24 Zero Ohm Resistor, 0402 Pkg. R3, R4 1 Ohm Resistor, 0402 Pkg. R12, R20, R29 51 Ohm Resistor, 0402 Pkg. R13, R14, R30 220 kOhm Resistor, 0402 Pkg. R22, R25 20 kOhm Resistor, 0402 Pkg. R26 - R28 1 kOhm Resistor, 0402 Pkg. R31 Zero Ohm Resistor, 0201 Pkg. R32, R33 Zero Ohm Resistor, 0805 Pkg. L1 8.2 nH Inductor, 0402 Pkg. L2, L3 47 nH Inductor, 0402 Pkg. L4 Zero Ohm Resistor, 0402 Pkg. TP1 - TP4 Test Point PC Compact SMT U1 HMC820LP6CE PLL with Integrated VCO U2 HMC860LP3E Low Noise Quad Linear Regulator Y1 3.3V, 50 MHz VCXO Crystal Oscillator PCB [2] 127729 Evaluation Board 7 PLLS w/ INTEGRATED VCO - SMT Item [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 or Arlon 25FR and FR4 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 7 - 12