Crane Aerospace & Electronics Power Solutions MHF+ Single, Dual and Triple DC/DC Converters 28 Volt input – 15 Watt Features Only 0.33 inches (8.38 mm) high in a hermetically sealed case • Operating temperature –55° to +125°C • Input voltage 16 to 40 VDC - MHF+281R9S 20 to 32 VDC - Triple output models16 to 48 VDC models VDC Output single 1.9 3.3 5 5.2 5.3 12 15 28 • Transient protection - Single and dual: 50 V for 50 ms - Triple: 80 V for 120 ms • Fully isolated • Fixed high frequency switching • Inhibit and synchronization functions • Indefinite short circuit protection Dual ±5 ±12 ±15 triple +5 & ±12 +5 & ±15 • Up to 84% efficiency DESCRIPTION MHF+ Single and Dual DC/DC converters The MHF+ Single and Dual Series™ of high frequency DC/ DC converters offers a wide input voltage range of 16 to 40 volts (MHF+281R9S, 20 to 32 volts) and up to 15 watts of output power. The units are capable of withstanding short term transients up to 50 volts. The converters are offered with standard screening, “ES” screening, or fully compliant to “883” MIL-PRF-38534 Class H screening. Standard microcircuit drawings (SMD) are available. Converter Design The MHF+ converters are switching regulators that use a quasi-square wave, single-ended forward converter design with a constant switching frequency of 550 kHz typical. Isolation between input and output circuits is provided with a transformer in the forward path and a temperature compensated optical link in the feedback control loop. See Figure 1. For the MHF+ dual output models, good cross regulation is maintained by tightly coupled output magnetics. Up to 90% of the total output power (80% on 2805D) is available from either output, providing the opposite output is simultaneously carrying 10% of the total output power (20% on 2805D models). Predictable current limit is accomplished by directly monitoring the output load current and providing a constant current output above the overload point. Inhibit Function MHF+ converters provide an inhibit terminal that can be used to disable internal switching, resulting in no output current and very low quiescent input current. The converter is inhibited when an active low of ≤0.8 V is applied to the inhibit pin. The unit is Crane Aerospace & Electronics Electronics Group (Interpoint Brand) PO Box 97005 • Redmond WA 98073-9705 425.882.3100 • [email protected] www.interpoint.com enabled when the pin, which is internally connected to a pull-up resistor, is left unconnected or is connected to an open-collector gate. The open circuit output voltage associated with the inhibit pin is 8.5 to 12 V. In the inhibit mode, a maximum of 4 mA must be sunk from the inhibit pin. See Figure 3. Synchronization An external synchronization feature is included that allows the user to adjust the nominally 550 kHz operating frequency to any frequency within the range of 500 kHz to 600 kHz. This is initiated by applying a signal input of the desired frequency to pin 5. The capacitively coupled sync input will synchronize on a differential signal of as low as 4 volts to as high as 5 V. For single and dual output models, if the sync function is not used, connect the terminal to input common. Short Circuit Protection MHF+ Series single and dual output converters provide short circuit protection by restricting the output current to approximately 115% of the full load output current. The output current is sensed in the secondary stage to provide highly predictable and accurate current limiting, and to eliminate foldback characteristics. Undervoltage Lockout Undervoltage lockout prevents the single and dual output converters from operating below approximately 14 VDC input voltage to keep system current levels smooth, especially during initialization or re-start operations. Page 1 of 23 MHF+ Rev L - 20091113 Crane Aerospace & Electronics Power Solutions MHF+ Single, Dual and Triple DC/DC Converters 28 Volt input – 15 Watt MHF+ Series™ Triple DC/DC converters MHF+ Series™ Triple DC/DC converters provide a wide input voltage range of 16 to 48 VDC delivering 15 watts of total output power with output voltages of +5 and ±12 or +5 and ±15 VDC. The main output, +5 VDC, will supply up to 7.5 watts and the auxiliaries will supply up to 7.5 watts of combined power. Full power operation at -55° C to +125° C plus the ability to withstand transients of up to 80 V for up to 120 milliseconds make these converters an ideal choice for your high reliability systems. Soft Start Feature The soft-start feature provides a controlled 25 milliseconds maximum turn-on to minimize inrush current and reduce overshoot at initial start-up or when inhibit is released. Synchronization MHF+ Triple Series of DC/DC converters incorporate dual-phase, phase-shifted technology with a continuous flyback topology. This design eliminates a minimum load requirement on the main output and eliminates cross regulation effects between the main output voltage and auxiliary output voltages. See Figure 2. The phase-shifted design offers reduced input and output ripple. To meet MIL-STD-461 requirements use an EMI filter, see Figure 5. FMH-461 is the recommended filter. To synchronize the converter’s switching frequency to a system clock apply the clock signal to the sync terminal (pin 7). When multiple converters are powered from a single power source, asynchronous (free run) operation will result in lower peak noise for common spectral peaks, but synchronous operation will eliminate any possibility of interference frequencies in the low audio band. Source impedance of the signal should be less than 100 ohms and the transition time should be less than 100 nanoseconds. The capacitively coupled sync input will synchronize on a differential signal of as low as 4 volts to as high as 5 V. For triple output models, if the sync function is not used, the terminal should be left open. See Figure 4. Inhibit Function Short Circuit Protection Converter Design An open collector inhibit terminal (pin 1) provides shut-down and start-up control. Applying an active low of <0.8 V, referenced to input common, will disable the output of the converter. When inhibited, input current is reduced to 5 mA or less and there is no generation of switching noise. The inhibit terminal typically sinks 3 mA when the converter is inhibited. Leaving the terminal open or pulling it high will enable the converter. Use an open collector interface for active high voltages of up to 11 volts. (Refer to Figure 2 for a connection diagram.) An open collector interface is not required if the active high is in excess of the open circuit voltage of the inhibit terminal (11 volts) but less than 40 volts. See Figure 2. MHF+ Series™ all Models Packaging MHF+ Series of converters are packaged in hermetically sealed metal cases and can be purchased in a flanged or non-flanged case. The flanged option provides increased heat dissipation and also provides greater stability when mechanically secured. On the triple output models, internal current limiting circuitry protects on all three outputs against short circuits. When output power exceeds approximately 130% of maximum output power, the output currents are limited. In addition, separate current limiting circuitry protects each output individually resulting in normal operation of either the main or the auxiliaries, whichever is not in a shorted condition. Undervoltage Lockout Undervoltage lockout prevents the triple output models units from operating below approximately 8.5 VDC input voltage to keep system current levels smooth, especially during initialization or re-start operations. Output Voltage Options The MHF+ Series converters are capable of providing other output voltage options in addition to those characterized on this datasheet. Contact your sales representative to discuss other output voltage options. US Patents Interpoint converters may use one or more of the following US patents 5,521,807, 5,694,303 and 5,631,822. www.interpoint.com Page 2 of 23 MHF+ Rev L - 20091113 Crane Aerospace & Electronics Power Solutions MHF+ Single, Dual and Triple DC/DC Converters 28 Volt input – 15 Watt Operating Conditions and characteristics Sync and inhibit Input Voltage Range •Single and dual models: ‣‣16 to 40 VDC continuous ‣‣MHF+281R9S 20 to 32 DC continuous ‣‣50 V for up to 50 ms transient ‣‣MHF+281R9S 35 V for up to 50 ms transient •Triple models: ‣‣16 to 48 VDC continuous ‣‣80 V for up to 120 ms transient Sync In •Input frequency ‣‣Single and dual models: 500 to 600 kHz ‣‣Triple models: 400 to 600 kHz ‣‣Duty cycle 40% to 60% •Active low 0.8 V max •Active high 4 V min, 5 V max •Triple models: source impedance should be <100 ohms and the transition time should be <100 nanoseconds •If sync is not used ‣‣Single and dual models: connect to input common ‣‣Triple models: leave unconnected •Referenced to input common Output Power •6.65 to 15 watts depending on model Power Dissipation (Pd) •Single and dual models: 6 watts •1.9 and 3.3V single: 8 watts •Triple models: 12 watts triple Output Voltage Temperature Coefficient •100 ppm/°C typical •150 ppm/°C maximum Inhibit: •Active low (output disabled) ‣‣Active low voltage ≤0.8 V max -- Inhibit pin current ·· Single and dual models: 4.0 mA max, 3.0 mA typ ·· Triple models: 5.0 mA max, 3.0 mA typ ‣‣Referenced to input common •Active high (output enabled) ‣‣Single and dual models -- Open collector or unconnected -- Open pin 8.5 to 12 V, 10 V typical ‣‣Triple models -- Open collector or unconnected -- Open collector interface not required if active high is greater than 11 V and less than 40V -- Open pin voltage, 11 V typical Current Limit •Single and dual models: 115% of full load typical •Triple models: 130% of full load typical triple mechanical and environmental Audio Rejection •50 dB typical Size (maximum) •Non flanged 1.460 x 1.130 x 0.330 (37.08 x 28.70 x 8.38 mm) •Flanged 2.005 x 1.130 x 0.330 (50.93 x 28.70 x 8.38 mm) •See cases E1, E2, G1 and G2 for dimensions. Lead Soldering Temperature (10 sec per pin) •300°C Storage Temperature Range (Case) •-65°C to +150°C Case Operating Temperature (TC) •-55°C to +125°C full power •-55°C to +135°C absolute Derating Output Power/Current •Linearly from 100% at 125°C to 0% at 135°C Input to Output Capacitance •60 pF typical Isolation •100 megohm minimum at 500 V Conversion Frequency (-55°C to +125°C TC) •Free run ‣‣Single and dual models: 480 kHz min, 550 kHz typ, 620 kHz max ‣‣Triple models: 375 kHz min, 500 kHz max Undervoltage Lockout •Single and dual models: 14 V input typical •Triple models: 8.5 V input typical www.interpoint.com Weight, flanged or unflanged (maximum) •Single and dual models: 30 grams •Triple models: 35 grams Screening: Standard, ES or 883 (Class H). See Screening Tables 1 and 2 for more information. Page 3 of 23 MHF+ Rev L - 20091113 Crane Aerospace & Electronics Power Solutions MHF+ Single, Dual and Triple DC/DC Converters 28 Volt input – 15 Watt Simplified Schematic Diagrams Positive Input 5 µH Positive Output 2 µF PWM Controller Inhibit FET Driver Limit ID Ref. IC Output Common Input Common Figure 1: MHF+ Single Output Block Diagram 0° Positive Input +5 Output FEEDBACK ISOLATOR PWM CM CONTROLLER Output Common Input Common FEEDBACK ISOLATOR Synv PWM CM CONTROLLER 180° –Aux. Output Figure 2: MHF+ Triple Output Block Diagram www.interpoint.com + Aux. Output Page 4 of 23 MHF+ Rev L - 20091113 Crane Aerospace & Electronics Power Solutions MHF+ Single, Dual and Triple DC/DC Converters 28 Volt input – 15 Watt CONNECTION DIAGRAMS POSITIVE INPUT MHF+ 9 10 k INHIBIT 1N4148 1 2N3501 200 pF 10 K 3.9 K 8 INPUT COMMON Figure 3: Inhibit Interface 9 0.01 28V 5.1k F 7 +5 Output 2 Positive Input + Aux. Output 4 Sync In Output Common 3 1 Inhibit 8 Input Common – Aux. Output 5 + Aux. Load +5 Load – Aux. Load If the sync terminal ([pin 7) is not used, it must be left floating. The ac coupling shown will prevent sync signal failure. Figure 4: AC Coupling 1 Positive Input Sync Signal, Triple Models of Positive Output 2 Positive Input FMH-461 EMI FILTER 28V 5 Input Common MHF+ Output Common 4 Case Ground 3 Input Common Case Ground Case* Chassis Ground *The case ground connection should be as low an impedance as possible to minimize EMI. Direct contact of baseplate to chassis ground provides the lowest impedance. Figure 5: EMI Filter Connection www.interpoint.com Page 5 of 23 MHF+ Rev L - 20091113 Crane Aerospace & Electronics Power Solutions MHF+ Single, Dual and Triple DC/DC Converters 28 Volt input – 15 Watt Pin Single Output MHF+2828S 1 Inhibit Inhibit 3 Output Common (See note 1) 2 No Connection 4 6 Sync In Case Ground 7 Input Common Positive Input 9 Main (+5) Output Output Common Negative Output Pos. Aux. Output Case Ground Case Ground Neg. Aux. Output Input Common Positive Input — Positive Output Inhibit Sync In Case Ground Input Common 8 Triple Output Output Common Output Common Sync In Dual Output Inhibit Positive Output Positive Output 5 PIN OUT Sync Positive Input — Input Common — Positive Input 1. Pin 3 of MHF+2828S will provide 14 Vout referenced to output common (pin 4). PINS NOT IN USE Inhibit: single, dual and triple, pin 1 Leave unconnected Sync: single and dual, pin 5 Connect to input common MHF+2828S, pin 3 Sync: triple, pin 7 Leave unconnected Leave unconnected Dot on top of case indicates pin one. 1 2 3 4 Squared corner and dot on top of case indicate pin one. 1 5 7 9 6 Dotted line outlines flanged package option. www.interpoint.com and 4 5 8 7 6 Dotted line outlines flanged package option. See cases E1 and G1 for dimensions. Figure 6: MHF+ Single 3 BOTTOM VIEW MHF+ Triple BOTTOM VIEW MHF+ SINGLE AND DUAL 8 2 See cases E2 and G2 for dimensions. Figure 7: MHF+ Triple Pin Out Dual Pin Out Page 6 of 23 MHF+ Rev L - 20091113 Crane Aerospace & Electronics Power Solutions MHF+ Single, Dual and Triple DC/DC Converters 28 Volt input – 15 Watt model numbering key MHF+ 28 12 D Base Model Input Voltage Output Voltage (R = decimal point, 3R3 = 3.3 Vout; Main and aux. Vout for triple models) SMD Numbers F / 883 Number of Outputs (S = single, D = dual, T = Triple) Case Option (Non-flanged case has no designator in this position) Screening (Standard screening has no designator in this position.) Standard Microcircuit Drawing (SMD) MHF+ Similar Part 5962-0251001HXC mhf+283r3s/883 5962-9213901HXC MHF+2805S/883 5962-0325301HXC mhf+285R2s/883 5962-9166401HXC MHF+2812S/883 5962-9160101HXC MHF+2815S/883 5962-9689801HXC mhf+2828S/883 5962-9555901hxc mhf+2805d/883 5962-9214401HXC MHF+2812D/883 5962-9161401HXC MHF+2815D/883 5962-9560101hxc MHF+28512t/883 5962-9560201hxc mhf+28515t/883 Flanged SMDs have the suffix HZC instead of HXC. For exact specifications for an SMD product, refer to the SMD drawing. SMDs can be downloaded from http:// www.dscc.dla.mil/programs/smcr On model selection the lines below, enter one selection from each category to determine the model number. Category SELECTION ___________ Mhf+28 Base Model and Input Voltage MHF+28 is the only available option Output Voltage 1 Number of Outputs 2 Case/Lead Options / 3 Screening 4 1R9, 3R3, 05, 5R2, 5R3, 12, 15, 28 S (non-flanged leave blank) (Standard leave blank) 05, 12, 15 D F (flanged) ES 512, 515 T 883 Notes: 1. Output Voltage: An R indicates a decimal point. 1R9 is 1.9 volts out. The values of 1R9, 3R3, 5R2 and 5R3 are only available in single output models. The 512 and 515 triple output converters are +5 volt main and ±12 or ±15 volt auxiliaries. 2. Number of Outputs: S is a single output, D is a dual output, and T is a triple output 3. Case Options: For the standard case (non-flanged) leave the case option blank. For the flanged case, use an F in the case option. 4. Screening: For standard screening leave the screening option blank. For other screening options, insert the desired screening level. For more information see Screening Tables 1 and 2. www.interpoint.com Page 7 of 23 MHF+ Rev L - 20091113 Crane Aerospace & Electronics Power Solutions MHF+ Single, Dual and Triple DC/DC Converters 28 Volt input – 15 Watt Electrical Characteristics: -55° TO +125°C TC , 28 VDC Vin, 100% load, free run, unless otherwise specified. single output models PARAMETER MHF+281R9S CONDITIONS OUTPUT VOLTAGE OUTPUT CURRENT OUTPUT POWER OUTPUT RIPPLE 10 kHz - 2 MHz LINE REGULATION Vin = 16 Vin = 16 to 40 VDC to 40 VDC TC = 25°C VIN = 16 TO 40 VDC MHF+283R3S MHF+2805S UNITS MIN TYP MAX MIN TYP MAX MIN TYP MAX 1.84 1.90 1.96 3.20 3.30 3.40 4.85 5.00 5.15 VDC 0 – 3.5 0 — 2.4 0 — 2.4 A W 0 — 6.65 0 — 8 0 — 12 — 7 30 — 30 80 — 30 80 — 12 40 — 50 240 — 60 100 mV p-p — 1 40 – 5 100 — 5 50 mV LOAD REGULATION NO LOAD TO FULL 2 — 35 55 – 20 50 — 20 50 mV INPUT VOLTAGE NO LOAD TO FULL CONTINUOUS TRANSIENT 50 ms 1 20 28 32 16 28 40 16 28 40 VDC — — 35 — — 50 — — 50 V INPUT CURRENT INPUT RIPPLE CURRENT 10 kHz - 10 MHz NO LOAD — 16 35 — 25 40 — 25 40 INHIBITED — 2 7 — 5 12 — 5 12 TC = 25°C — 30 60 – 45 80 — 35 80 — — 70 — — 120 — — 100 56 62 — 67 75 – 72 77 — POWER DISSIPATION SHORT CIRCUIT — 4 8 — 5 8 — 3.5 6 RECOVERY 1 — 5 30 — 7.5 30 — 7.5 30 ms 50% - 100% - 50% TRANSIENT — ±75 ±500 — ±150 ±400 — ±150 ±400 mV pk RECOVERY — 500 2000 — 150 300 — 150 300 µs — ±300 ±600 — ±550 ±800 — ±550 ±800 mV pk RECOVERY — 0.5 1.2 — 0.8 1.2 — 0.8 1.2 ms DELAY OVERSHOOT 1 — 12 35 – 10 25 — 10 25 ms — 500 850 — 200 300 — 100 600 mV pk — — 100 – – 300 – – 300 µF EFFICIENCY LOAD FAULT 3, 4 STEP LOAD RESPONSE 4, 5 STEP LINE RESPONSE 1, 4, 5 START-UP 5 Capacitive Load 1 16 - 40 - 16 VDC TRANSIENT 6 Notes 1. Guaranteed by design, not tested. 2. For MHF+281R9, load regulation is tested from a 10 mA load to full load. 3.Indefinite short circuit protection not guaranteed above 125°C (case). 4.Recovery time is measured from application of the transient. to the point at which VOUT is within regulation. www.interpoint.com 5.Step transition time >10 µs. 6. Step line is 20 - 32 - 20 VDC for MHF+281R39S. Page 8 of 23 MHF+ Rev L - 20091113 mA mA p-p % W Crane Aerospace & Electronics Power Solutions MHF+ Single, Dual and Triple DC/DC Converters 28 Volt input – 15 Watt Electrical Characteristics: -55° TO +125°C TC , 28 VDC Vin, 100% load, free run, unless otherwise specified. single output models PARAMETER MHF+285R2S CONDITIONS OUTPUT VOLTAGE OUTPUT CURRENT OUTPUT POWER Vin = 16 Vin = 16 OUTPUT RIPPLE to 40 VDC to 40 VDC LINE REGULATION LOAD REGULATION INPUT VOLTAGE NO LOAD TO FULL INPUT CURRENT INPUT RIPPLE CURRENT 10 kHz - 10 MHz LOAD FAULT STEP LOAD RESPONSE 4, 3 STEP LINE RESPONSE 1, 3, 4 START-UP 4 Capacitive Load 1 TYP MAX MIN TYP MAX MIN TYP MAX 5.04 5.20 5.36 5.19 5.35 5.51 11.76 12.00 12.24 VDC 0 — 2.4 0 — 2.83 0 — 1.25 A W — 12.48 0 — 15 0 — 15 30 50 — 30 50 — 30 80 — 60 100 — 60 100 — 50 120 VIN = 16 TO 40 VDC — 5 50 — 5 50 — 5 50 mV NO LOAD TO FULL — 20 50 — 20 50 — 20 50 mV CONTINUOUS TRANSIENT 50 ms 1 16 28 40 16 28 40 16 28 40 VDC — — 50 — — 50 — — 50 V mV p-p NO LOAD — 25 43 — 24 43 — 25 50 INHIBITED — 5 12 — 5 12 — 5 12 TC = 25°C — 35 80 — 35 80 — 35 80 — — 120 — — 120 — — 120 72 77 — 72 77 — 74 79 — % POWER DISSIPATION SHORT CIRCUIT — 3.5 6 — 3.5 6 — 3.5 6 W RECOVERY 1 — 7.5 30 — 7.5 30 — 7.5 30 ms 50% - 100% - 50% TRANSIENT — ±150 ±400 — ±150 ±400 — ±150 ±500 mV pk RECOVERY — 150 300 — 150 300 — 150 300 µs 16 - 40 - 16 VDC TRANSIENT — ±550 ±800 — ±550 ±800 — ±550 ±800 mV pk RECOVERY — 0.8 1.2 — 0.8 1.2 — 0.8 1.2 ms DELAY — 10 25 — 10 25 — 10 25 ms OVERSHOOT 1 — 100 600 — 100 600 — 200 1200 mV pk — — 300 — — 300 — — 100 µF Notes 1. Guaranteed by design, not tested. 2.Indefinite short circuit protection not guaranteed above 125°C (case). 3.Recovery time is measured from application of the transient. to the point at which VOUT is within regulation. www.interpoint.com UNITS MIN 0 EFFICIENCY 2, 3 MHF+2812S — TC = 25°C 10 kHz - 2 MHz MHF+285R3S 4.Step transition time >10 µs. Page 9 of 23 MHF+ Rev L - 20091113 mA mA p-p Crane Aerospace & Electronics Power Solutions MHF+ Single, Dual and Triple DC/DC Converters 28 Volt input – 15 Watt Electrical Characteristics: -55° TO +125°C TC, 28 VDC Vin, 100% load, free run, unless otherwise specified. single output models PARAMETER MHF+2815S CONDITIONS OUTPUT VOLTAGE OUTPUT CURRENT OUTPUT POWER Vin = 16 Vin = 16 OUTPUT RIPPLE to 40 VDC to 40 VDC LINE REGULATION LOAD REGULATION INPUT VOLTAGE NO LOAD TO FULL INPUT CURRENT INPUT RIPPLE CURRENT 10 kHz - 10 MHz TYP MAX MIN TYP MAX 14.70 15.00 15.30 27.44 28.00 28.56 VDC 0 — 1.00 0 — 0.536 A W 0 — 15 0 — 15 — 30 80 — 60 120 — 50 120 — 100 180 VIN = 16 TO 40 VDC — 5 50 — 50 150 mV NO LOAD TO FULL — 20 50 — 50 150 mV CONTINUOUS TRANSIENT 50 ms 1 16 28 40 16 28 40 VDC — — 50 — — 50 V LOAD FAULT STEP LOAD RESPONSE 3, 4 STEP LINE RESPONSE 1, 3, 4 START-UP 4 Capacitive Load NO LOAD — 25 62 — 25 60 — 5 12 — 5 12 TC = 25°C — 35 80 — 35 80 — — 120 — — 120 74 80 — 78 84 — % POWER DISSIPATION SHORT CIRCUIT — 3.5 6 — 3.5 6 W RECOVERY 1 — 7.5 30 — 7.5 30 ms 50% - 100% - 50% TRANSIENT — ±200 ±600 — ±600 ±800 mV pk RECOVERY — 150 300 — 200 400 µs 16 - 40 - 16 VDC TRANSIENT — ±550 ±800 — ±1100 ±1200 mV pk RECOVERY — 0.8 1.2 — 0.8 1.2 ms DELAY — 10 25 — 10 25 ms OVERSHOOT 1 — 200 1500 — 200 280 mV pk — — 100 — — 100 µF 1 Notes 1. Guaranteed by design, not tested. 2.Indefinite short circuit protection not guaranteed above 125°C (case). 3.Recovery time is measured from application of the transient . to the point at which VOUT is within regulation. www.interpoint.com mV p-p INHIBITED EFFICIENCY 2, 3 UNITS MIN TC = 25°C 10 kHz - 2 MHz MHF+2828S 4.Step transition time >10 µs. Page 10 of 23 MHF+ Rev L - 20091113 mA mA p-p Crane Aerospace & Electronics Power Solutions MHF+ Single, Dual and Triple DC/DC Converters 28 Volt input – 15 Watt Electrical Characteristics: -55° TO +125°C TC, 28 VDC Vin, 100% load, free run, unless otherwise specified. DUAL output models PARAMETER OUTPUT VOLTAGE OUTPUT CURRENT 2, 3 Vin = 16 to Vin = 16 to 40 VDC OUTPUT POWER 2, 3 40 VDC OUTPUT RIPPLE ±VOUT, 10kHz - 2 MHz MHF+2805D MHF+2812D MHF+2815D CONDITIONS MIN TYP MAX MIN TYP MAX MIN TYP MAX +Vout 4.85 5.00 5.15 11.76 12.00 12.24 14.70 15.00 15.30 -Vout 4.82 5.00 5.18 11.70 12.00 12.30 14.63 15.00 15.38 Each Output 0 ±1.2 1.92 1 0 ±0.625 1.125 1 0 ±0.50 0.90 1 Total — — 2.4 — — 1.25 — — 1.0 Each Output 0 ±6 9.6 1 0 ±7.5 13.5 1 0 ±7.5 13.5 1 Total — — 12 — — 15 — — 15 TC = 25°C — 30 80 — 30 80 — 30 60 — 60 80 — 60 120 — 50 120 UNITS VDC A W mV p-p LINE REGULATION Vin = 16 to 40 VDC +Vout — 5 50 — 5 50 — 5 50 — — 80 — — 100 — — 100 LOAD REGULATION Balanced Loads No Load to Full -Vout +Vout — 20 50 — 20 50 — 20 50 -Vout — — 100 — — 100 — — 100 25°C EFFECT ON -Vout — 6 7.5 — 3 6 — 3 5 % 16 28 40 16 28 40 16 28 40 VDC V CROSS REGULATION 4 INPUT VOLTAGE INPUT CURRENT INPUT RIPPLE CURRENT 10 kHz - 10 MHz CONTINUOUS TRANSIENT 50 ms 1 — — 50 — — 50 — — 50 NO LOAD — 20 40 — 25 50 — 25 50 INHIBITED — 6 12 — 5 12 — 5 12 TC = 25°C EFFICIENCY LOAD FAULT 5, 6 STEP LOAD RESPONSE 7, 8 50% - 100% - 50% Balanced Loads STEP LINE RESPONSE 1, 8 ±Vout START-UP 8 Vin = 40 V Capacitive Load 1 — 20 50 — 35 60 — 35 60 — 40 80 — 50 100 — 50 100 mV mA mA p-p 75 79 — 74 83 — 75 84 — % POWER DISSIPATION SHORT CIRCUIT — 3 6 — 3 6 — 3 6 W RECOVERY 1 — 7.5 30 — 7.5 30 — 7.5 30 ms TRANSIENT +Vout — ±200 ±600 — ±300 ±700 — ±300 ±700 — ±150 ±600 — ±100 ±700 — ±100 ±700 RECOVERY — 150 500 — 200 500 — 200 500 µs 16 - 40 - 16 Vin TRANSIENT — ±600 ±800 — ±550 ±750 — ±550 ±750 mV pk RECOVERY — 0.8 1.2 — 0.8 1.2 — 0.8 1.2 ms DELAY — 12 20 — 12 25 — 12 25 ms — 80 250 — 200 750 — 200 750 mV pk — — 47 — — 10 — — 10 µF TRANSIENT -Vout OVERSHOOT 1 Notes (see following page) www.interpoint.com mV Page 11 of 23 MHF+ Rev L - 20091113 mV pk Crane Aerospace & Electronics Power Solutions MHF+ Single, Dual and Triple DC/DC Converters 28 Volt input – 15 Watt Electrical Characteristics: -55° TO +125°C TC, 28 VDC Vin, 100% load, free run, unless otherwise specified. Notes for Dual Output Models 1. Guaranteed by design, not tested. 2.Up to 13.5 watts, 90% (9.6 watts, 80% for 2805D) of the total output power is available from either output provided that the opposite output is simultaneously carrying 10% (20% for 2805D) of the total output power. One of the outputs must always provide a minimum of 10% (20% for 2805D) of the total output power used to meet cross regulation. Negative Vout cross regulation is referenced to 50%/50% balanced loads (at 100% of total rated output power - full load). 3. The “Total” specification is the maximum combined current/power of both outputs. 4.Effect on –VOUT for the following conditions, A and B: Condition A: +Po = 50% to 10% and –Po = 50% +Po = 50% and –Po = 50% to 10% Condition B, outputs are switched simultaneously between the “From” and “To” conditions: From +Po = 70%, –Po = 30% To +Po = 30%, –Po = 70% Both conditions are referenced to the balanced loads condition: 50%/50% www.interpoint.com 5.Indefinite short circuit protection not guaranteed above 125°C (case) 6.Recovery time is measured from application of the transient to point at which VOUT is within regulation. 7.Response of either output with the opposite output held at half of the total output power. 8.Step transition time >10 µs. Page 12 of 23 MHF+ Rev L - 20091113 Crane Aerospace & Electronics Power Solutions MHF+ Single, Dual and Triple DC/DC Converters 28 Volt input – 15 Watt Electrical Characteristics: -55° TO +125°C TC, 28 VDC Vin, 100% load, free run, unless otherwise specified. 5 2 (main) triple output model – MHF+28512T PARAMETER OUTPUT VOLTAGE OUTPUT CURRENT 3 MIN TYP MAX MIN Vout 4.85 2 5.00 5.15 — — 1.5 Total — — — Total 10 kHz - 2 MHz OUTPUT POWER 4 Vin = 16 - 48 VDC OUTPUT RIPPLE LINE REGULATION LOAD REGULATION Vin= 16 6 CROSS REGULATION 6 TC = 25°C to TYP MAX ±11.52 ±12.00 0 ±0.313 ±12.48 0.416 1 1.5 — — 0.625 — 7.5 — ±3.75 51 — — 7.5 — — 7.5 VDC A W — 20 90 — ±30 ±180 mV p-p 48 VDC — 25 75 — ±120 ±240 mV NO LOAD TO FULL — 22 75 — ±120 ±240 mV — — — — — 6.25 % CONTINUOUS 16 28 48 — — — VDC TRANSIENT 1 120 ms — — 80 — — — V INPUT CURRENT INPUT RIPPLE CURRENT EFFICIENCY LOAD FAULT 7, 9 8, 9 STEP LINE RESPONSE 1, 9, 10 START-UP Notes 1. Guaranteed by design, not tested. NO LOAD — 30 45 — — — INHIBITED — 3 5 — — — 10 kHz - 20 MHz — 20 50 — — — mA p-p mA 72 76 — — — — % POWER DISSIPATION SHORT CIRCUIT — — 12 — — ±12 W RECOVERY 1 — — 25 — — 25 ms TRANSIENT — — ±850 — — ±950 mV pk RECOVERY — 5 8 — 2 3 ms 16 - 48 - 16 TRANSIENT — — ±800 — — ±800 mV pk RECOVERY — — 5 — — 5 ms DELAY NO LOAD AND FULL — 10 25 — 10 ±25 ms OVERSHOOT 1 — — 500 — — ±500 mV pk 2. If running with external sync, at temperature extremes VOUT main may be a minimum of 4.80 VDC to a maximum of 5.20 VDC. 3. The sum of the 12 volt auxiliary output currents may not exceed 625 mA. 4. The sum of the auxiliary output power may not exceed 7.5 watts. Up to 5 watts (approximately 66%) of the total auxiliary output power is available from either output providing the opposite output is simultaneously carrying 2.5 watts (approximately 33%) of the total auxiliary power. 5.Load regulation for the +5 is specified at 0.0 to 1.5 A with the auxiliaries both held at 3.75 W (313 mA). Load regulation for the auxiliaries is specified as both auxiliaries from 0.0 to 3.75 W (313 mA) at the same time with the +5 held at 1.5 A. www.interpoint.com UNITS EFFECT ON NEGATIVE AUXILIARY INPUT VOLTAGE STEP LOAD RESPONSE ±12 (AUXiliaries) CONDITIONS 6. Cross regulation only occurs between the two auxiliaries and is measured on –aux. +5 is held constant at 1.0 A. Cross regulation is specified for two conditions: Negative aux.= 3.76 W; positive aux.= 0.37 W to 3.76 W. Negative aux. = 0.37 W to 3.76 W; positive aux. = 3.76 W. 7. Load fault = < 0.100 Ω. 8. Step transition time > 10 µs. 9. Time to settle to within 1% of VOUT final value. 10. Step transition time between 2 and 10 µs. Page 13 of 23 MHF+ Rev L - 20091113 Crane Aerospace & Electronics Power Solutions MHF+ Single, Dual and Triple DC/DC Converters 28 Volt input – 15 Watt Electrical Characteristics: -55° TO +125°C TC, 28 VDC Vin, 100% load, free run, unless otherwise specified. 5 2 (MAIN) triple output model – MHF+28515T PARAMETER OUTPUT VOLTAGE OUTPUT CURRENT 3 MIN TYP MAX MIN Vout 4.85 5.00 5.15 — — 1.5 — — — TOTAL TOTAL OUTPUT POWER 9 Vin = 16 to 48 VDC OUTPUT RIPPLE LINE REGULATION LOAD REGULATION NO LOAD TO FULL 5 CROSS REGULATION 6 TC = 25°C INPUT VOLTAGE INPUT RIPPLE CURRENT EFFICIENCY LOAD FAULT 7, 9 STEP LOAD RESPONSE 8, 9 STEP LINE RESPONSE 1, 9, 10 START-UP Notes 1. Guaranteed by design, not tested. MAX 14.40 15.00 0 ±0.250 15.60 0.333 1 1.5 — — 0.500 — 7.5 — ±2.5 51 — — — — — 7.5 UNITS VDC A W 10 kHz - 2 MHz — 20 90 — ±30 ±225 mV p-p — 25 75 — ±150 ±300 mV Vin = 28 VDC — 25 75 — ±150 ±300 mV EFFECT ON NEGATIVE AUXILIARY OUTPUT — — — — — 5.0 % CONTINUOUS 16 28 48 — — — VDC — — 80 — — — V 1 120 ms NO LOAD — 30 45 — — — INHIBITED — 3 5 — — — 10 kHz - 20 MHz — 20 50 — — — mA mA p-p 72 76 — — — — % POWER DISSIPATION SHORT CIRCUIT — — 12 — — ±12 W RECOVERY 1 — — 25 — — 25 ms TRANSIENT — — ±850 — — ±950 mV pk RECOVERY — 5 8 — 2 3 ms 16 - 48 - 16 VIN TRANSIENT — — ±800 — — ±800 mV pk RECOVERY — — 5 — — 5 ms DELAY NO LOAD AND FULL — 10 25 — 10 25 ms OVERSHOOT 1 — — 500 — — ±500 mV pk 2. If running with external sync, at temperature extremes VOUT main may be a minimum of 4.80 VDC to a maximum of 5.20 VDC. 3. The sum of the 15 volt auxiliary output currents may not exceed 500 mA. 4. The sum of the auxiliary output power may not exceed 7.5 watts. Up to 5 watts (approximately 66%) of the total auxiliary output power is available from either output providing the opposite output is simultaneously carrying 2.5 watts (approximately 33%) of the total auxiliary power. 5.Load regulation for the +5 is specified at 0.0 to 1.5 A with both auxiliaries held at 3.75 W (250 mA). Load regulation for the auxiliary. is specified as both auxiliaries from 0.0 to 3.75 W (250 mA) at the same time with the +5 held at 1.5 A. www.interpoint.com TYP Vin= 16, 48 VDC TRANSIENT INPUT CURRENT ±15 (AUXILIARIES) CONDITIONS 6. Cross regulation only occurs between the two auxiliaries and is measured on –aux. +5 is held constant at 1.0 A. Cross regulation is specified for two conditions: Negative aux.= 3.76 W; positive aux.= 0.37 W to 3.76 W. Negative aux. = 0.37 W to 3.76 W; positive aux. = 3.76 W. 7. Load fault = < 0.100 Ω. 8. Step transition time > 10 µs. 9. Time to settle to within 1% of VOUT final value. 10. Step transition time between 2 and 10 µs. Page 14 of 23 MHF+ Rev L - 20091113 Crane Aerospace & Electronics Power Solutions MHF+ Single, Dual and Triple DC/DC Converters 28 Volt input – 15 Watt Typical Performance Curves: 25°C Tc , 28 VDC Vin, 100% load, free run, unless otherwise specified. 90 16V 70 40V 28V 60 50 70 40V 60 50 2 4 6 8 10 40 12 4 2 6 8 10 12 40 14 15 2 4 16V EFFICIENCY (%) 70 40V 60 28V 4 6 8 10 40 12 70 40V 60 28V 50 50 50 14 15 80 80 28V 12 90 16V 40V 10 Figure 10 16V 70 8 MHF+2815S EFFICIENCY 90 80 6 OUTPUT POWER (Watts) Figure 9 90 EFFICIENCY (%) 28V 60 MHF+2812S EFFICIENCY Figure 8 2 40V OUTPUT POWER (Watts) MHF+2805S EFFICIENCY 40 70 50 OUTPUT POWER (Watts) 60 16V 80 28V EFFICIENCY (%) 40 16V 80 EFFICIENCY (%) EFFICIENCY (%) 80 90 EFFICIENCY (%) 90 4 2 OUTPUT POWER (Watts) 6 8 10 12 40 14 15 OUTPUT POWER (Watts) MHF+2805D EFFICIENCY 4 6 8 10 12 14 OUTPUT POWER (Watts) MHF+2812D EFFICIENCY Figure 11 2 MHF+2815D EFFICIENCY Figure 13 Figure 12 0 –30 –40 –50 VOUT 100% to 50% 100mV/div. 500mV/div. –20 –60 –70 50% to 100% 20V/div. ATTENUATION (dB) –10 –80 –90 –100 0.1 1 10 FREQUENCY (kHz) MHF+ SERIES AUDIO REJECTION Figure 14 www.interpoint.com 100 VIN 1ms/div 16V TO 40V MHF+2805S STEP LINE RESPONSE Figure 15 Page 15 of 23 MHF+ Rev L - 20091113 50µs/div 50% 100% MHF+2805S STEP LOAD RESPONSE Figure 16 Crane Aerospace & Electronics Power Solutions MHF+ Single, Dual and Triple DC/DC Converters 28 Volt input – 15 Watt VIN 100mV/div. 100% to 10% 200mV/div. 20V/div. Typical Performance Curves: 25°C Tc , 28 VDC Vin, 100% load, free run, unless otherwise specified. +VOUT 1V/div. 200µs/div 10% 100% POUT= 12W VOUT VIN 2 ms/div 1 ms/div 16V TO 40V MHF+2805S TURN-ON INTO FULL LOAD MHF+2805S STEP LOAD RESPONSE MHF+2815D STEP LINE RESPONSE Figure 18 Figure 17 100% to 50% 20V/div. 10% to 100% Figure 19 PO= 7.5 W PO= 7.5 W –VOUT 100mV/div. 100mV/div. 5V/div. 100% to 20% +VOUT 20V/div. 20% to 100% 50% to 100% 50µs/div 50% 100% MHF+2815D +VOUT STEP LOAD RESPONSE 50µs/div 20% 100% MHF+2815D +VOUT STEP LOAD RESPONSE 10 MHF+2815D TURN-ON INTO FULL LOAD Figure 22 16 10 5 2812D 2815D 0 –5 2805D 6 20 40 60 80 100 POSITIVE OUTPUT LOAD (% OF TOTAL LOAD) –VOUT WITH SHIFT IN LOAD BALANCE CROSS REGULATION Figure 23 www.interpoint.com 2812D 4 COND A 2 0 2815D –2 COND B –4 2812D –6 –8 –10 0 MHF+2805S&D 2805D 8 2805D 10 20 30 40 50 OUTPUT LOAD (%) COND. A: 50% LOAD +V; 50% to 10% –V COND. B: 50% LOAD –V; 50% to 10% +V MHF+2805D/MHF+2812D/MHF+2815D CROSS REGULATION Figure 24 Page 16 of 23 MHF+ Rev L - 20091113 INPUT VOLTAGE (Volts) –VOUT VOLTAGE CHANGE (%) –V OUT VOLTAGE CHANGE (%) 2 ms/div Figure 21 Figure 20 –10 VIN 15 14 MHF+2812S&D MHF+2815S&D 13 12 10 11 12 13 14 OUTPUT POWER (Watts) 50 mV DROP 15 LOW LINE DROPOUT VS. LOAD Figure 25 Crane Aerospace & Electronics Power Solutions MHF+ Single, Dual and Triple DC/DC Converters 28 Volt input – 15 Watt Typical Performance Curves: 25°C Tc , 28 VDC Vin, 100% load, free run, unless otherwise specified. 75 75 EFFICIENCY EFFICIENCY 28 V 70 48 V 65 60 55 16 V 200 mV / div. 80 16 V 28 V 70 48 V 65 60 2 4 6 8 10 12 14 16 55 4 2 6 10 8 12 14 OUTPUT POWER (W) OUTPUT POWER (W) MHF+28512T EFFICIENCY MHF+28515T EFFICIENCY 16 MHF+ 28515T STEP LINE RESPONSE Figure 28 VIN +5 VDC 2 V / div. INPUT GND 2 V / div. INPUT GND +5 GND +5 VDC +5 GND 5 ms / div. 5 ms / div. MHF+28512T TURN ON INTO FULL LOAD MAIN MHF+28512T TURN ON INTO FULL LOAD MAIN MHF+28515T has a similar response MHF+28515T has a similar response Figure 29 Figure 30 10 V / div. 11.5 VIN –12 VDC 5 ms / div. MHF+28512T TURN ON INTO FULL LOAD AUXILIARIES MHF+28515T has a similar response Figure 31 www.interpoint.com INPUT VOLTAGE 5 V / div. +12 VDC 11 MHF+28515T 10.5 10 MHF+28512T 9.5 9 8.5 2 4 6 8 –15 VDC MHF+28512T has a similar response 10 V / div. 10 V / div. VIN +15 VDC 5 ms / div. INPUT V: 16 TO 40 VDC, ±15 = 250 mA EACH, +5 = 1.5 A Figure 27 Figure 26 5 VDC 500 mV / div. 80 10 12 14 MAXIMUM OUTPUT POWER (W) LOW LINE DROPOUT Figure 32 Page 17 of 23 MHF+ Rev L - 20091113 16 Crane Aerospace & Electronics Power Solutions MHF+ Single, Dual and Triple DC/DC Converter Cases 28 Volt input – 15 Watt BOTTOM VIEW CASE E1 Projection Weld Squared corner and dot on top of case indicate pin one. 1.130 max. (28.70) 0.960 (24.38) 1 0.030 dia. (0.76) 2 8 0.160 (4.06) 3 4 7 5 6 1.460 max. (37.08) 1.105 (28.07) 0.905 (22.99) 0.705 (17.91) 0.505 (12.83) 0.205 (5.21) 0.000 0.25 (6.35) 0.000 0.330 max. (8.38) 0.000 Case dimensions in inches (mm) Tolerance ±0.005 (0.13) for three decimal places ±0.01 (0.3) for two decimal places unless otherwise specified CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300°C for 10 seconds per pin. Materials Header Cold Rolled Steel/Nickel/Gold Cover Kovar/Nickel Pins #52 alloy/Gold compression glass seal. Seal Hole: 0.080 ±0.002 (2.03 ±0.05) Case E1, Rev D, 20091105 Please refer to the numerical dimensions for accuracy. All information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice. Copyright © 1999-2009 Interpoint Corp. All rights reserved. Figure 33: Case E1— Single www.interpoint.com and Dual Models Page 18 of 23 MHF+ Rev L - 20091113 Crane Aerospace & Electronics Power Solutions MHF+ Single, Dual and Triple DC/DC Converter Cases 28 Volt input – 15 Watt BOTTOM VIEW CASE E2 1 3 4 5 8 7 6 1.105 (28.07) 0.960 (24.38) Squared corner and dot on top of case indicate pin one. 0.905 (22.99) 1.130 max. (28.70) 0.705 (17.91) Projection Weld 2 0.030 dia. (0.76) 9 0.160 (4.06) 1.460 max. (37.08) 0.505 (12.83) 0.205 (5.21) 0.000 0.25 (6.35) 0.000 0.330 max (8.38) 0.000 Case dimensions in inches (mm) Tolerance ±0.005 (0.13) for three decimal places ±0.01 (0.3) for two decimal places unless otherwise specified CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300°C for 10 seconds per pin. Materials Header Cold Rolled Steel/Nickel/Gold Cover Kovar/Nickel Pins #52 alloy/Gold compression glass seal. Seal Hole: 0.080 ±0.002 (2.03 ±0.05) Case E2, Rev D, 20091105 Please refer to the numerical dimensions for accuracy. All information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice. Copyright © 1999-2009 Interpoint Corp. All rights reserved. Figure 34: Case E2 — Triple Models www.interpoint.com Page 19 of 23 MHF+ Rev L - 20091113 Crane Aerospace & Electronics Power Solutions MHF+ Single, Dual and Triple DC/DC Converter Cases 28 Volt input – 15 Watt BOTTOM VIEW CASE G1 Flanged cases: Designator "F" required in Case Option position of model number Projection Weld Squared corner and dot on top of case indicate pin one. 1.130 max. (28.70) 0.960 (24.38) 1 0.030 dia. (0.76) 0.560 (14.22) 2 3 4 2 x Dia 0.128 (3.25) 5 2 x R 0.130 (3.30) 8 0.160 (4.06) 7 6 1.590 (40.39) 1.105 (28.07) 0.905 (22.99) 0.705 (17.91) 0.505 (12.83) 0.205 (5.21) 0.000 0.140 (3.56) 0.25 (6.35) 0.000 0.330 max. (8.38) 0.000 (2.005 max (50.93)) Flange thickness: 0.047 (1.19) Case dimensions in inches (mm) Tolerance ±0.005 (0.13) for three decimal places ±0.01 (0.3) for two decimal places unless otherwise specified CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300°C for 10 seconds per pin. Materials Header Cold Rolled Steel/Nickel/Gold Cover Kovar/Nickel Pins #52 alloy/Gold compression glass seal. Seal Hole: 0.080 ±0.002 (2.03 ±0.05) Case G1, Rev C, 20091105 Please refer to the numerical dimensions for accuracy. All information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice. Copyright © 1999-2009 Interpoint Corp. All rights reserved. Figure 35: Case G1 — Single www.interpoint.com and Dual Models Page 20 of 23 MHF+ Rev L - 20091113 Crane Aerospace & Electronics Power Solutions MHF+ Single, Dual and Triple DC/DC Converter Cases 28 Volt input – 15 Watt BOTTOM VIEW CASE G2 Flanged cases: Designator "F" required in Case Option position of model number Projection Weld Squared corner and dot on top of case indicate pin one. 1.130 max. (28.70) 0.960 (24.38) 1 2 3 4 2 x Dia 0.128 (3.25) 5 2 x R 0.130 (3.30) 8 7 6 1.105 (28.07) 9 0.160 (4.06) 0.905 (22.99) 0.560 (14.22) 0.705 (17.91) 0.030 dia. (0.76) 1.590 (40.39) 0.505 (12.83) 0.205 (5.21) 0.000 0.140 (3.56) 0.25 (6.35) 0.000 0.330 max. (8.38) 0.000 (2.005 max (50.93)) Flange thickness: 0.047 (1.19) Case dimensions in inches (mm) Tolerance ±0.005 (0.13) for three decimal places ±0.01 (0.3) for two decimal places unless otherwise specified CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300°C for 10 seconds per pin. Materials Header Cold Rolled Steel/Nickel/Gold Cover Kovar/Nickel Pins #52 alloy/Gold compression glass seal. Seal Hole: 0.080 ±0.002 (2.03 ±0.05) Case G2, Rev D, 20091105 Please refer to the numerical dimensions for accuracy. All information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice. Copyright © 1999-2009 Interpoint Corp. All rights reserved. Figure 36: Case G2 — Triple Models www.interpoint.com Page 21 of 23 MHF+ Rev L - 20091113 Crane Aerospace & Electronics Power Solutions MHF+ Single, Dual and Triple DC/DC Converters 28 Volt input – 15 Watt STANDARD AND /ES (NON-QML) AND /883 (CLASS H, QML) PRODUCT ELEMENT EVALUATION COMPONENT-LEVEL TEST PERFORMED STANDARD AND /ES NON-QML 1 M/S 2 /883 CLASS H QML P3 M/S 2 element electrical (probe) yes no yes yes element visual no no yes yes internal visual no n/a yes n/a Final electrical no no yes yes Wire bond evaluation 4 no no yes yes slam™/C-sam: input capacitors only (add’l test, not req. by h) no no no yes notes: 1. Standard and /eS, non-QMl products, do no meet all of the requirements of Mil-PrF-38534. 2. M/S = active components (Microcircuit and Semiconductor die) 3. P = Passive components 4. not applicable to eMi filters that have no wire bonds. definitions: element evaluation: Component testing/screening per Mil-Std-883 as determined by Mil-PrF-38534 SlaM™: Scanning laser acoustic Microscopy C-SaM: C - Mode Scanning acoustic Microscopy Screening Table 1: Element Evaluation www.interpoint.com P3 Page 22 of 23 MHF+ Rev L - 20091113 Crane Aerospace & Electronics Power Solutions MHF+ Single, Dual and Triple DC/DC Converters 28 Volt input – 15 Watt STANDARD AND /ES (NON-QML) AND /883 (CLASS H, QML) PRODUCT ENVIRONMENTAL SCREENING 125°C STANDARD NON-QML1 125°C /ES NON-QML1 /883 CLASS H QML Pre-cap inspection method 2017, 2032 yes yes yes temperature Cycle (10 times) method 1010, Cond. C, -65°C to 150°C, ambient method 1010, Cond. b, -55°C to 125°C, ambient no no no yes yes no Constant acceleration method 2001, 3000 g method 2001, 500 g no no no yes yes no burn-in 2 method 1015, 125°C case, typical 96 hours 160 hours no no yes no no yes Final electrical test mil-PrF-38534, group a subgroups 1 through 6: -55°C, +25°C, +125°C case subgroups 1 and 4: +25°C case no yes no yes yes no hermeticity test Fine leak, method 1014, Cond. a gross leak, method 1014, Cond. C gross leak, dip (1 x 10-3) no no yes yes yes no yes yes no Final visual inspection method 2009 yes yes yes TEST PERFORMED test methods are referenced to Mil-Std-883 as determined by Mil-PrF-38534. notes: 1. Standard and /eS, non-QMl products, do not meet all of the requirements of Mil-PrF-38534. 2. Burn-in temperature designed to bring the case temperature to +125°C Screening Table 2: Environmental Screening MHF+ Single, Dual and Triple. MHF+ Rev L - 20091113 This revision supersedes all previous releases. All technical information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice. MHF+ Series is a trademark of Interpoint. Copyright © 1999 - 2009 Interpoint Corporation. All rights reserved. www.interpoint.com Page 23 of 23