SI5412-H / SI5412-H(B) IRED Features • • • • Blue Colored transparency lens type φ5mm(T-13/4) all plastic mold type Low power consumption High radiant intensity Applications • Light source for remote control devices (This device should be only used at non- repetitive pulse mode) Outline Dimensions unit : mm STRAIGHT TYPE STOPPER 4.60~5.00 4.60~5.00 8.80~9.20 0.05 Typ. 0.05 Typ. TYPE : (B) 8.80~9.20 1.40 Max. 1.40 Max. 1.20 Min. 3.30~4.30 23.00 Min. 0.60 Max. 0.55 Max. 0.60 Max. 23.00 Min. 1.00 Min. 1.00 Min. 2.54 Typ. 1 2 5.45~6.05 0.55 Max. 0.55 Max. 2.54 Typ. 1 2 5.45~6.05 PIN Connections 1. Anode 2. Cathode KSD-O2P010-001 1 SI5412-H / SI5412-H(B) Absolute Maximum Ratings Characteristic (Ta=25℃) Symbol Rating Unit PD 150 mW 1 Power dissipation IF 100 mA 2 IFP 1 A Reverse voltage VR 4 V Operating temperature range Topr -25∼85 ℃ Storage temperature range Tstg -30∼100 ℃ * Forward current * Peak forward current 3 * Soldering temperature Tsol 260℃ for 10 seconds *1.Avoid operating under continuous bias *2.Duty ratio = 1/100, Pulse width = 0.1ms *3.Keep the distance more than 2.0mm from PCB to the bottom of IRED package Electrical / Optical Characteristics Characteristic (Ta=25℃) Symbol Test Condition Min. Typ. Max. Unit Forward voltage VF IF= 50mA - 1.3 1.5 V Radiant intensity IE IF= 50mA 30 65 - mW/Sr Peak wavelength λP Δλ IR IF= 50mA - 950 - nm IF= 50mA - 50 - nm VR=4V - - 10 uA θ1/2 IF= 50mA - ±8 - deg Spectrum bandwidth Reverse current 4 * Half angle *4. θ1/2 is the off-axis angle where the luminous intensity is 1/2 the peak intensity KSD-O2P010-001 2 SI5412-H / SI5412-H(B) Characteristic Diagrams Fig. 1 IF-VF Forward Current IF [mA] Radiant Intensity IE [mW/Sr] Fig. 2 IE - IF Forward Voltage VF [V] Forward Fig. 3 IF – Ta Current IF [mA] Forward Relative Intensity [%] Current IF [mA] Fig.4 Spectrum Distribution Wavelength λ [nm] Ambient Temperature Ta [℃] Fig. 5 Radiation Diagram 100 50 0 50 100 Relative Radiant Intensity IE [%] KSD-O2P010-001 3 SI5412-H / SI5412-H(B) The AUK Corp. products are intended for the use as components in general electronic equipment (Office and communication equipment, measuring equipment, home appliance, etc.). Please make sure that you consult with us before you use these AUK Corp. products in equipments which require high quality and / or reliability, and in equipments which could have major impact to the welfare of human life(atomic energy control, airplane, spaceship, transportation, combustion control, all types of safety device, etc.). AUK Corp. cannot accept liability to any damage which may occur in case these AUK Corp. products were used in the mentioned equipments without prior consultation with AUK Corp.. Specifications mentioned in this publication are subject to change without notice. KSD-O2P010-001 4