LIGITEK LY25030/S2

LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
ROUND TYPE LED LAMPS
LY25030/S2
DATA SHEET
DOC. NO :
QW0905- LY25030/S2-08
REV.
:
C
DATE
:
15 - Jul. - 2008
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
Page 1/5
PART NO. LY25030/S2
Package Dimensions
5.6
LIGHTED AREA
3.64
3.18
6.16
REFERENCE MARK
S E
6.65
0.38
1.0MAX
0.5
TYP
26.4MIN
1.0MIN.
2.54TYP
-
+
Note : 1.All dimension are in millimeter tolerance is ±0.25mm unless otherwise noted.
2.Specifications are subject to change without notice.
Directivity Radiation
0°
-30°
30°
-60°
100% 75% 50%
60°
25%
0
25%
50% 75% 100%
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
PART NO. LY25030/S2
Page 2/5
Absolute Maximum Ratings at Ta=25 ℃
Ratings
Symbol
Parameter
UNIT
Yellow
Forward Current
IF
15
mA
Peak Forward Current
Duty 1/[email protected]
IFP
50
mA
Power Dissipation
PD
50
mW
Reverse Current @5V
Ir
10
μA
Operating Temperature
Topr
-40 ~ +85
℃
Storage Temperature
Tstg
-40 ~ +100
℃
Typical Electrical & Optical Characteristics (Ta=25 ℃)
PART NO
COLOR
MATERIAL
Emitted
LY25030-S2
Forward
Peak Spectral
voltage
wave halfwidth
length △λ nm @ 10mA(V)
λPnm
@10mA(mcd)
Viewing
angle
2θ 1/2
(deg)
Min. Typ. Min. Typ.
Lens
GaAsP/GaP Yellow Yellow Diffused
Luminous
intensity
585
35
1.7
Note : 1.The forward voltage data did not including ±0.1V testing tolerance.
2. The luminous intensity data did not including ±15% testing tolerance.
2.1
8.0
20
120
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
PART NO. LY25030/S2
Page3/5
Typical Electro-Optical Characteristics Curve
Y CHIP
Fig.2 Relative Intensity vs. Forward Current
Relative Intensity
Normalize @20mA
Forward Current(mA)
Fig.1 Forward current vs. Forward Voltage
Forward Current(mA)
Forward Voltage(V)
Ambient Temperature( ℃)
Ambient Temperature( ℃)
Fig.5 Relative Intensity vs. Wavelength
Relative [email protected]
Fig.4 Relative Intensity vs. Temperature
Relative [email protected]
Normalize @25℃
Forward [email protected]
Normalize @25℃
Fig.3 Forward Voltage vs. Temperature
1.0
0.5
0.0
500
550
600
650
Wavelength (nm)
700
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
PART NO. LY25030/S2
Page 4/5
Soldering Condition(Pb-Free)
1.Iron:
Soldering Iron:30W Max
Temperature 350° C Max
Soldering Time:3 Seconds Max(One time only)
Distance:2mm Min(From solder joint to body)
2.Wave Soldering Profile
Dip Soldering
Preheat: 120° C Max
Preheat time: 60seconds Max
Ramp-up
2°C/sec(max)
Ramp-Down:-5° C/sec(max)
Solder Bath:260°C Max
Dipping Time:3 seconds Max
Distance:2mm Min(From solder joint to body)
Temp(° C)
260° C3sec Max
260°
5° /sec
max
120°
25°
0° 0
2° /sec
max
Preheat
60 Seconds Max
50
100
Note: 1.Wave solder should not be made more than one time.
2.You can just only select one of the soldering conditions as above.
150
Time(sec)
LIGITEK ELECTRONICS CO.,LTD.
Property of Ligitek Only
Page 5/5
PART NO. LY25030/S2
Reliability Test:
Test Item
Test Condition
Description
Reference
Standard
Operating Life Test
1.Under Room Temperature
2.If=20mA
3.t=1000 hrs (-24hrs, +72hrs)
This test is conducted for the purpose
of detemining the resistance of a part
in electrical and themal stressed.
MIL-STD-750: 1026
MIL-STD-883: 1005
JIS C 7021: B-1
High Temperature
Storage Test
1.Ta=105 ℃±5 ℃
2.t=1000 hrs (-24hrs, +72hrs)
The purpose of this is the resistance of
the device which is laid under condition
of high temperature for hours.
MIL-STD-883:1008
JIS C 7021: B-10
Low Temperature
Storage Test
1.Ta=-40 ℃±5℃
2.t=1000 hrs (-24hrs, +72hrs)
The purpose of this is the resistance
of the device which is laid under
condition of low temperature for hours.
High Temperature
High Humidity Test
1.Ta=65 ℃±5℃
2.RH=90 %~95 %
3.t=240hrs ±2hrs
The purpose of this test is the resistance
of the device under tropical for hours.
1.Ta=105 ℃±5 ℃&-40 ℃±5℃
(10min) (10min)
2.total 10 cycles
The purpose of this is the resistance of
the device to sudden extreme changes
in high and low temperature.
MIL-STD-202: 107D
MIL-STD-750: 1051
MIL-STD-883: 1011
Solder Resistance
Test
1.T.Sol=260 ℃±5℃
2.Dwell time= 10 ±1sec.
This test intended to determine the
thermal characteristic resistance
of the device to sudden exposures
at extreme changes in temperature
when soldering the lead wire.
MIL-STD-202: 210A
MIL-STD-750: 2031
JIS C 7021: A-1
Solderability Test
1.T.Sol=230 ℃±5℃
2.Dwell time=5 ±1sec
This test intended to see soldering well
performed or not.
MIL-STD-202: 208D
MIL-STD-750: 2026
MIL-STD-883: 2003
JIS C 7021: A-2
Thermal Shock Test
JIS C 7021: B-12
MIL-STD-202:103B
JIS C 7021: B-11