LINEAGEPOWER NSR006A0X4-49Z

Data Sheet
December 6, 2010
Naos Raptor 6A: Non-Isolated DC-DC Power Modules
4.5Vdc –14Vdc input; 0.59Vdc to 6Vdc Output; 6A Output Current
Features
RoHS Compliant
Applications

Distributed power architectures

Intermediate bus voltage applications

Telecommunications equipment

Servers and storage applications

Networking equipment

Industrial Applications

Compliant to RoHS EU Directive 2002/95/EC (Z
versions)

Compatible in a Pb-free or SnPb wave-soldering
environment (Z versions)

Wide Input voltage range (4.5Vdc-14Vdc)

Output voltage programmable from 0.59 Vdc to 6Vdc
via external resistor

Tunable Loop
response

Fixed switching frequency

Output overcurrent protection (non-latching)

Over temperature protection

Remote On/Off

Cost efficient open frame design

Small size:
TM
to optimize dynamic output voltage
10.4 mm x 16.5 mm x 7.84 mm
(0.41 in x 0.65 in x 0.31 in)

Wide operating temperature range (-40°C to 85°C)

UL* 60950-1Recognized, CSA† C22.2 No. 60950-1‡
03 Certified, and VDE 0805:2001-12 (EN60950-1)
Licensed

ISO** 9001 and ISO 14001 certified manufacturing
facilities
Description
The Naos Raptor 6A SIP power modules are non-isolated dc-dc converters in an industry standard package that
can deliver up to 6A of output current with a full load efficiency of 91.5% at 3.3Vdc output voltage (VIN = 12Vdc).
These modules operate over a wide range of input voltage (VIN = 4.5Vdc-14Vdc) and provide a precisely regulated
output voltage from 0.59Vdc to 6Vdc, programmable via an external resistor. Features include remote On/Off,
TM
adjustable output voltage, over current and over temperature protection. A new feature, the Tunable Loop , allows
the user to optimize the dynamic response of the converter to match the load.
* UL is a registered trademark of Underwriters Laboratories, Inc.
†
CSA is a registered trademark of Canadian Standards Association.
VDE is a trademark of Verband Deutscher Elektrotechniker e.V.
** ISO is a registered trademark of the International Organization of Standards
‡
Document No: DS06-125 ver. 1.12
PDF name: NSR006A0X_ds.pdf
Data Sheet
December 6, 2010
Naos Raptor 6A: Non-isolated DC-DC Power Modules
4.5 – 14Vdc input; 0.59Vdc to 6Vdc Output; 6A output current
Absolute Maximum Ratings
Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are
absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in
excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for
extended periods can adversely affect the device reliability.
Parameter
Device
Symbol
Min
Max
Unit
All
VIN
-0.3
15
Vdc
All
TA
-40
85
°C
All
Tstg
-55
125
°C
Input Voltage
Continuous
Operating Ambient Temperature
(see Thermal Considerations section)
Storage Temperature
Electrical Specifications
Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature
conditions.
Parameter
Device
Symbol
Min
Typ
Max
Unit
Operating Input Voltage
All
VIN
4.5
12
14
Vdc
Maximum Input Current
All
IIN,max
5.5
Adc
(VIN=4.5V to 14V, IO=IO, max )
Input No Load Current
(VIN = 9Vdc, IO = 0, module ON)
VO,set = 0.6 Vdc
IIN,No load
30
(VIN = 12Vdc, IO = 0, module ON)
VO,set = 5.0Vdc
IIN,No load
50
mA
All
IIN,stand-by
1
mA
Inrush Transient
All
It
Input Reflected Ripple Current, peak-to-peak
(5Hz to 20MHz, 1μH source impedance; VIN =0 to
14V, IO= IOmax ; See Test Configurations)
All
35
mAp-p
Input Ripple Rejection (120Hz)
All
50
dB
Input Stand-by Current
mA
(VIN = 12Vdc, module disabled)
LINEAGE POWER
2
1
2
As
2
Data Sheet
December 6, 2010
Naos Raptor 6A: Non-isolated DC-DC Power Modules
4.5 – 14Vdc input; 0.59Vdc to 6Vdc Output; 6A output current
Electrical Specifications (continued)
Parameter
Device
Symbol
Min
Output Voltage Set-point (with 0.5% tolerance
for external resistor used to set output voltage)
All
VO, set
-1.5
Output Voltage
All
VO, set
-3.0
All
VO
0.59
Typ
Max
Unit
+1.5
% VO, set
+3.0
% VO, set
6
Vdc
⎯
+0.2
% VO, set
⎯
0.8
% VO, set
⎯
+5
mV
⎯
20
mV
⎯
(Over all operating input voltage, resistive load,
and temperature conditions until end of life)
Adjustment Range
Selected by an external resistor
Output Regulation (for Vo ≥ 2.5Vdc)
Line (VIN=VIN, min to VIN, max)
All
Load (IO=IO, min to IO, max)
All
-0.2
Output Regulation (for Vo <2.5Vdc)
Line (VIN=VIN, min to VIN, max)
All
Load (IO=IO, min to IO, max)
All
-5
Output Ripple and Noise on nominal output
(VIN=VIN, nom and IO=IO, min to IO, max Cout = 0.0μF)
Peak-to-Peak (5Hz to 20MHz bandwidth)
VO = 0.59Vdc
⎯
20
mVpk-pk
Peak-to-Peak (5Hz to 20MHz bandwidth)
VO = 1.2Vdc
⎯
23
mVpk-pk
Peak-to-Peak (5Hz to 20MHz bandwidth)
VO = 1.8Vdc
⎯
25
mVpk-pk
Peak-to-Peak (5Hz to 20MHz bandwidth)
VO = 2.5Vdc
⎯
30
mVpk-pk
Peak-to-Peak (5Hz to 20MHz bandwidth)
VO = 3.3Vdc
⎯
40
mVpk-pk
Peak-to-Peak (5Hz to 20MHz bandwidth)
VO = 5.0Vdc
⎯
50
mVpk-pk
Peak-to-Peak (5Hz to 20MHz bandwidth)
VO = 6.0Vdc
⎯
60
mVpk-pk
External Capacitance
1
TM
Without the Tunable Loop
ESR ≥ 1 mΩ
With the Tunable Loop
All
CO, max
0
⎯
200
μF
All
CO, max
0
⎯
1000
μF
⎯
5000
μF
6
Adc
TM
ESR ≥ 0.15 mΩ
All
CO, max
0
Output Current
ESR ≥ 10 mΩ
All
Io
0
Output Current Limit Inception (Hiccup Mode )
All
IO, lim
150
% Io,max
Output Short-Circuit Current
All
IO, s/c
9.3
Adc
VO,set = 0.59Vdc
η
71.8
%
VIN= 12Vdc, TA=25°C
VO, set = 1.2Vdc
η
81.6
%
IO=IO, max , VO= VO,set
VO,set = 1.8Vdc
η
86.7
%
VO,set = 2.5Vdc
η
89.7
%
VO,set = 3.3Vdc
η
91.9
%
VO,set = 5.0Vdc
η
94.2
%
VO,set = 6.0Vdc
η
95.1
All
fsw
(VO≤250mV) ( Hiccup Mode )
Efficiency
(VIN= 9Vdc)
Switching Frequency
1
⎯
600
%
⎯
kHz
TM
External capacitors may require using the new Tunable Loop feature to ensure that the module is stable as well as
TM
getting the best transient response. See the Tunable Loop section for details.
LINEAGE POWER
3
Data Sheet
December 6, 2010
Naos Raptor 6A: Non-isolated DC-DC Power Modules
4.5 – 14Vdc input; 0.59Vdc to 6Vdc Output; 6A output current
General Specifications
Parameter
Min
Calculated MTBF (VIN=12V, VO=5Vdc, IO=0.8IO, max, TA=40°C) Per
Telcordia Method
Max
Unit
8,727,077
⎯
Weight
Typ
Hours
⎯
2.9 (0.10)
g (oz.)
Feature Specifications
Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature
conditions. See Feature Descriptions for additional information.
Parameter
Device
Symbol
Min
Typ
Max
Unit
―
0.5
mA
1.0
―
12
V
On/Off Signal interface
(VIN=VIN, min to VIN, max; Open collector or equivalent
signal referenced to GND)
Logic High (On/Off pin open - Module ON)
Input High Current
All
IIH
Input High Voltage
All
VIH
Logic Low (Module Off)
Input Low Current
All
IIL
―
―
200
μA
Input Low Voltage
All
VIL
-0.3
―
0.4
V
All
Tdelay
2
3
msec
All
Tdelay
2
3
msec
All
Trise
3
5
msec
0.5
% VO, set
Turn-On Delay and Rise Times
(IO=IO, max , VIN = VIN, nom, Vo to within ±1% of steady state)
Case 1: On/Off input is enabled and then
input power is applied (delay from instant at which
VIN =VIN, min until Vo=10% of Vo,set)
Case 2: Input power is applied for at least one second
and then On/Off input is set enabled (delay from
instant at which On/Off is enabled until Vo=10% of Vo,
set)
Output voltage Rise time (time for Vo to rise from 10%
of Vo,set to 90% of Vo, set)
Output voltage overshoot
o
IO= IO, max; VIN = VIN, min to VIN, max, TA = 25 C
Overtemperature Protection
All
120
ºC
Turn-on Threshold
All
4.2
Vdc
Turn-off Threshold
All
4.1
Vdc
Input Undervoltage Lockout
LINEAGE POWER
4
Data Sheet
December 6, 2010
Naos Raptor 6A: Non-isolated DC-DC Power Modules
4.5 – 14Vdc input; 0.59Vdc to 6Vdc Output; 6A output current
Characteristic Curves
The following figures provide typical characteristics for the Naos Raptor 6A module at 0.6Vout and at 25ºC.
82
7
OUTPUT CURRENT, Io (A)
EFFICIENCY, η (%)
80
78
Vin = 4.5V
76
Vin = 6V
74
Vin = 9V
72
70
0
1
2
3
4
5
LINEAGE POWER
35
45
55
65
75
85
IO (A) (2Adiv)
OUTPUT VOLTAGE
OUTPUT CURRENT,
VO (V) (200mV/div)
Figure 2. Derating Output Current versus Ambient
Temperature and Airflow.
TIME, t (100μs /div)
VO (V) (200mV/div)
VIN (V) (5V/div)
Figure 4. Transient Response to Dynamic Load
Change from 0% to 50% to 0% with VIN=9V.
OUTPUT VOLTAGE
VO (V) (200mV/div)
VON/OFF (V) (5V/div)
Figure 5. Typical Start-up Using On/Off Voltage (Io =
Io,max).
3
O
INPUT VOLTAGE
VO (V) (10mV/div)
OUTPUT VOLTAGE
OUTPUT VOLTAGE
ON/OFF VOLTAGE
TIME, t (1ms/div)
4
AMBIENT TEMPERATURE, TA C
Figure 1. Converter Efficiency versus Output Current.
TIME, t (1μs/div)
NC
5
25
6
OUTPUT CURRENT, IO (A)
Figure 3. Typical output ripple and noise (VIN = 9V, Io =
Io,max).
6
TIME, t (1ms/div)
Figure 6. Typical Start-up Using Input Voltage (VIN =
9V, Io = Io,max).
5
Data Sheet
December 6, 2010
Naos Raptor 6A: Non-isolated DC-DC Power Modules
4.5 – 14Vdc input; 0.59Vdc to 6Vdc Output; 6A output current
Characteristic Curves (continued)
The following figures provide typical characteristics for the Naos Raptor 6A module at 1.2Vout and at 25ºC.
95
7
85
OUTPUT CURRENT, Io (A)
EFFICIENCY, η (%)
90
Vin = 4.5V
80
Vin = 14V
Vin = 12V
75
70
0
1
2
3
4
5
45
55
65
75
85
OUTPUT VOLTAGE
VO (V) (200mV/div)
IO (A) (2Adiv)
OUTPUT CURRENT,
TIME, t (100μs /div)
VO (V) (500mV/div)
VIN (V) (5V/div)
Figure 10. Transient Response to Dynamic Load
Change from 0% to 50% to 0% with VIN=12V.
OUTPUT VOLTAGE
VO (V) (500mV/div)
VON/OFF (V) (5V/div)
LINEAGE POWER
35
Figure 8. Derating Output Current versus Ambient
Temperature and Airflow.
INPUT VOLTAGE
VO (V) (10mV/div)
OUTPUT VOLTAGE
OUTPUT VOLTAGE
ON/OFF VOLTAGE
Figure 11. Typical Start-up Using On/Off Voltage (Io =
Io,max).
3
AMBIENT TEMPERATURE, TA C
Figure 7. Converter Efficiency versus Output Current.
TIME, t (1ms/div)
4
O
OUTPUT CURRENT, IO (A)
TIME, t (1μs/div)
NC
5
25
6
Figure 9. Typical output ripple and noise (VIN = 12V, Io =
Io,max).
6
TIME, t (1ms/div)
Figure 12. Typical Start-up Using Input Voltage (VIN =
12V, Io = Io,max).
6
Data Sheet
December 6, 2010
Naos Raptor 6A: Non-isolated DC-DC Power Modules
4.5 – 14Vdc input; 0.59Vdc to 6Vdc Output; 6A output current
Characteristic Curves (continued)
The following figures provide typical characteristics for the Naos Raptor 6A module at 1.8Vout and at 25ºC.
95
7
OUTPUT CURRENT, Io (A)
EFFICIENCY, η (%)
90
Vin = 4.5V
85
Vin = 14V
Vin = 12V
80
75
70
0
1
2
3
4
5
LINEAGE POWER
35
45
55
65
75
85
IO (A) (2Adiv)
OUTPUT VOLTAGE
OUTPUT CURRENT,
VO (V) (200mV/div)
Figure 14. Derating Output Current versus Ambient
Temperature and Airflow.
TIME, t (100μs /div)
VO (V) (1V/div)
VIN (V) (5V/div)
Figure 16. Transient Response to Dynamic Load
Change from 0% to 50% to 0% with VIN=12V.
OUTPUT VOLTAGE
VO (V) (1V/div)
VON/OFF (V) (5V/div)
Figure 17. Typical Start-up Using On/Off Voltage (Io =
Io,max).
3
O
INPUT VOLTAGE
VO (V) (10mV/div)
OUTPUT VOLTAGE
OUTPUT VOLTAGE
ON/OFF VOLTAGE
TIME, t (1ms/div)
4
AMBIENT TEMPERATURE, TA C
Figure 73. Converter Efficiency versus Output Current.
TIME, t (1μs/div)
NC
5
25
6
OUTPUT CURRENT, IO (A)
Figure 15. Typical output ripple and noise (VIN = 12V, Io
= Io,max).
6
TIME, t (1ms/div)
Figure 18. Typical Start-up Using Input Voltage (VIN =
12V, Io = Io,max).
7
Data Sheet
December 6, 2010
Naos Raptor 6A: Non-isolated DC-DC Power Modules
4.5 – 14Vdc input; 0.59Vdc to 6Vdc Output; 6A output current
Characteristic Curves (continued)
The following figures provide typical characteristics for the Naos Raptor 6A module at 2.5Vout and at 25ºC.
100
7
OUTPUT CURRENT, Io (A)
EFFICIENCY, η (%)
95
90
85
Vin = 12V
Vin = 14V
Vin = 4.5V
80
75
70
0
1
2
3
4
5
LINEAGE POWER
3
35
45
55
65
75
85
IO (A) (2Adiv)
OUTPUT VOLTAGE
OUTPUT CURRENT,
VO (V) (200mV/div)
Figure 20. Derating Output Current versus Ambient
Temperature and Airflow.
TIME, t (100μs /div)
VO (V) (1V/div)
VIN (V) (5V/div)
Figure 22. Transient Response to Dynamic Load
Change from 0% to 50% to 0% with VIN=12V.
OUTPUT VOLTAGE
VO (V) (1V/div)
VON/OFF (V) (5V/div)
Figure 23. Typical Start-up Using On/Off Voltage (Io =
Io,max).
4
AMBIENT TEMPERATURE, TA C
INPUT VOLTAGE
VO (V) (10mV/div)
OUTPUT VOLTAGE
OUTPUT VOLTAGE
ON/OFF VOLTAGE
TIME, t (1ms/div)
0.5m/s
(100LFM)
O
Figure 19. Converter Efficiency versus Output Current.
Figure 21. Typical output ripple and noise (VIN = 12V, Io
= Io,max).
NC
5
25
6
OUTPUT CURRENT, IO (A)
TIME, t (1μs/div)
6
TIME, t (1ms/div)
Figure 24. Typical Start-up Using Input Voltage (VIN =
12V, Io = Io,max).
8
Data Sheet
December 6, 2010
Naos Raptor 6A: Non-isolated DC-DC Power Modules
4.5 – 14Vdc input; 0.59Vdc to 6Vdc Output; 6A output current
Characteristic Curves
The following figures provide typical characteristics for the Naos Raptor 6A module at 3.3Vout and at 25ºC.
100
7
OUTPUT CURRENT, Io (A)
EFFICIENCY, η (%)
95
90
Vin = 12V
85
Vin = 14V
Vin = 4.5V
80
75
70
0
1
2
3
4
5
LINEAGE POWER
3
35
45
55
65
75
85
IO (A) (5Adiv)
OUTPUT VOLTAGE
OUTPUT CURRENT,
VO (V) (200mV/div)
Figure 26. Derating Output Current versus Ambient
Temperature and Airflow.
TIME, t (100μs /div)
VO (V) (1V/div)
VIN (V) (5V/div)
Figure 28. Transient Response to Dynamic Load
Change from 0% to 50% to 0% with VIN=12V.
OUTPUT VOLTAGE
VO (V) (1V/div)
VON/OFF (V) (5V/div)
Figure 29. Typical Start-up Using On/Off Voltage (Io =
Io,max).
4
AMBIENT TEMPERATURE, TA C
INPUT VOLTAGE
VO (V) (10mV/div)
OUTPUT VOLTAGE
OUTPUT VOLTAGE
ON/OFF VOLTAGE
TIME, t (1ms/div)
NC
0.5m/s
(100LFM)
O
Figure 25. Converter Efficiency versus Output Current.
Figure 27. Typical output ripple and noise (VIN = 12V, Io
= Io,max).
5
25
6
OUTPUT CURRENT, IO (A)
TIME, t (1μs/div)
6
TIME, t (1ms/div)
Figure 30. Typical Start-up Using Input Voltage (VIN =
12V, Io = Io,max).
9
Data Sheet
December 6, 2010
Naos Raptor 6A: Non-isolated DC-DC Power Modules
4.5 – 14Vdc input; 0.59Vdc to 6Vdc Output; 6A output current
Characteristic Curves (continued)
The following figures provide typical characteristics for the Naos Raptor 6A module at 5Vout and at 25ºC.
100
7
90
Vin = 12V
85
OUTPUT CURRENT, Io (A)
EFFICIENCY, η (%)
95
Vin = 14V
Vin = 6V
80
75
70
0
1
2
3
4
5
LINEAGE POWER
4
3
35
45
55
65
75
85
AMBIENT TEMPERATURE, TA C
OUTPUT VOLTAGE
VO (V) (200mV/div)
IO (A) (2Adiv)
OUTPUT CURRENT,
TIME, t (100μs /div)
VO (V) (2V/div)
VIN (V) (5V/div)
Figure 34. Transient Response to Dynamic Load
Change from 0% to 50% to 0% with VIN=12V.
OUTPUT VOLTAGE
VO (V) (2V/div)
VON/OFF (V) (5V/div)
Figure 35. Typical Start-up Using On/Off Voltage (Io =
Io,max).
NC
Figure 32. Derating Output Current versus Ambient
Temperature and Airflow.
INPUT VOLTAGE
VO (V) (10mV/div)
OUTPUT VOLTAGE
OUTPUT VOLTAGE
ON/OFF VOLTAGE
TIME, t (1ms/div)
0.5m/s
(100LFM)
O
Figure 31. Converter Efficiency versus Output Current.
Figure 33. Typical output ripple and noise (VIN = 12V, Io
= Io,max).
5
25
6
OUTPUT CURRENT, IO (A)
TIME, t (1μs/div)
6
TIME, t (1ms/div)
Figure 36. Typical Start-up Using Input Voltage (VIN =
12V, Io = Io,max).
10
Data Sheet
December 6, 2010
Naos Raptor 6A: Non-isolated DC-DC Power Modules
4.5 – 14Vdc input; 0.59Vdc to 6Vdc Output; 6A output current
Characteristic Curves
The following figures provide typical characteristics for the Naos Raptor 6A module at 6Vout and at 25ºC.
7
100
Vin = 12V
90
85
OUTPUT CURRENT, Io (A)
EFFICIENCY, η (%)
95
Vin = 14V
Vin = 7V
80
75
70
0
1
2
3
4
5
6
LINEAGE POWER
4
3
35
45
55
65
75
85
AMBIENT TEMPERATURE, TA C
VO (V) (200mV/div)
IO (A) (2Adiv)
OUTPUT CURRENT,
OUTPUT VOLTAGE
Figure 41. Typical Start-up Using On/Off Voltage (Io =
Io,max).
NC
Figure 38. Derating Output Current versus Ambient
Temperature and Airflow.
TIME, t (100μs /div)
OUTPUT VOLTAGE
VO (V) (2V/div)
VIN (V) (5V/div)
Figure 40. Transient Response to Dynamic Load
Change from 0% to 50% to 0% with VIN=12V.
INPUT VOLTAGE
VO (V) (10mV/div)
OUTPUT VOLTAGE
OUTPUT VOLTAGE
VO (V) (2V/div)
VON/OFF (V) (5V/div)
ON/OFF VOLTAGE
TIME, t (1ms/div)
0.5m/s
(100LFM)
O
Figure 37. Converter Efficiency versus Output Current.
TIME, t (1μs/div)
5
25
OUTPUT CURRENT, IO (A)
Figure 39. Typical output ripple and noise (VIN = 12V, Io
= Io,max).
6
TIME, t (1ms/div)
Figure 42. Typical Start-up Using Input Voltage (VIN =
12V, Io = Io,max).
11
Data Sheet
December 6, 2010
Naos Raptor 6A: Non-isolated DC-DC Power Modules
4.5 – 14Vdc input; 0.59Vdc to 6Vdc Output; 6A output current
Test Configurations
Design Considerations
CURRENT PROBE
The Naos Raptor 6A module should be connected to
a low-impedance source. A highly inductive source
can affect the stability of the module. An input
capacitance must be placed directly adjacent to the
input pin of the module, to minimize input ripple
voltage and ensure module stability.
To minimize input voltage ripple, low-ESR ceramic or
polymer capacitors are recommended at the input of the
module. Figure 46 shows the input ripple voltage for
various output voltages at 6A of load current with 1x22
µF or 2x22 µF ceramic capacitors and an input of 12V.
LTEST
VIN(+)
BATTERY
1μH
CIN
CS 1000μF
Electrolytic
2x100μF
Tantalum
E.S.R.<0.1Ω
@ 20°C 100kHz
COM
NOTE: Measure input reflected ripple current with a simulated
source inductance (LTEST) of 1μH. Capacitor CS offsets
possible battery impedance. Measure current as shown
above.
160
Figure 43. Input Reflected Ripple Current Test
Setup.
COPPER STRIP
VO (+)
RESISTIVE
LOAD
1uF
.
10uF
SCOPE
COM
GROUND PLANE
NOTE: All voltage measurements to be taken at the module
terminals, as shown above. If sockets are used then
Kelvin connections are required at the module terminals
to avoid measurement errors due to socket contact
resistance.
Figure 44. Output Ripple and Noise Test Setup.
Rdistribution
Rcontact
Rcontact
VIN(+)
Input Filtering
Input Ripple Voltage (mVp-p)
TO OSCILLOSCOPE
140
1x22uF
120
2x22uF
100
80
60
40
20
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
Output Voltage (Vdc)
Figure 46. Input ripple voltage for various output
voltages with 1x22 µF or 2x22 µF ceramic
capacitors at the input (6A load). Input voltage is
12V.
Rdistribution
VO
Output Filtering
VO
VIN
Rdistribution
RLOAD
Rcontact
Rcontact
COM
Rdistribution
COM
NOTE: All voltage measurements to be taken at the module
terminals, as shown above. If sockets are used then
Kelvin connections are required at the module terminals
to avoid measurement errors due to socket contact
resistance.
Figure 45. Output Voltage and Efficiency Test Setup.
VO. IO
Efficiency
η =
LINEAGE POWER
VIN. IIN
x
100 %
The Naos Raptor 6A modules are designed for low
output ripple voltage and will meet the maximum output
ripple specification with no external capacitors.
However, additional output filtering may be required by
the system designer for a number of reasons. First,
there may be a need to further reduce the output ripple
and noise of the module. Second, the dynamic
response characteristics may need to be customized to
a particular load step change.
To reduce the output ripple and improve the dynamic
response to a step load change, additional capacitance
at the output can be used. Low ESR ceramic and
polymer are recommended to improve the dynamic
response of the module. Figure 47 provides output
ripple information for different external capacitance
values at various Vo and for a load current of 6A. For
stable operation of the module, limit the capacitance to
less than the maximum output capacitance as specified
in the electrical specification table. Optimal
12
Data Sheet
December 6, 2010
Naos Raptor 6A: Non-isolated DC-DC Power Modules
4.5 – 14Vdc input; 0.59Vdc to 6Vdc Output; 6A output current
performance of the module can be achieved by using
the Tunable LoopTM feature described later in this data
sheet.
40
1x10uF
1x47uF
2x47uF
4x47uF
Ripple(mVp-p)
30
External
External
External
External
Cap
Cap
Cap
Cap
20
10
0
0.5
1
1.5
2
2.5
3
3.5
Output Voltage(Volts)
4
4.5
5
Figure 47. Output ripple voltage for various output
voltages with external 1x10 µF, 1x47 µF, 2x47 µF or
4x47 µF ceramic capacitors at the output (6A load).
Input voltage is 12V.
Safety Considerations
For safety agency approval the power module must be
installed in compliance with the spacing and separation
requirements of the end-use safety agency standards,
i.e., UL 60950-1, CSA C22.2 No. 60950-1-03, and VDE
0850:2001-12 (EN60950-1) Licensed.
For the converter output to be considered meeting the
requirements of safety extra-low voltage (SELV), the
input must meet SELV requirements. The power
module has extra-low voltage (ELV) outputs when all
inputs are ELV.
An input fuse for the module is recommended. Due to
the wide input voltage and output voltage ranges of the
module, different fuse ratings are recommended as
shown in Table 1. These are suggested “maximum”
fuse ratings. However, for optimum circuit protection,
the fuse value should not be any larger than required in
the end application. As an option to using a fuse, no
fuse is required, if the module is
1. powered by a power source with current limit
protection set point less than the protection
device value listed in Table 1, and
2. the module is evaluated in the end-use
equipment.
Table 1.
Input
Output Voltage (VDC)
Voltage
0.59 to 1.3 1.31 to 2.7 2.71 to 5.0 5.1 to 6
(VDC)
10.1 to 14
3A
6A
10A
12A
6.51 to 10
4A
8A
15A
12A
4.5 to 6.5
6A
12A
15A
NA
LINEAGE POWER
13
Data Sheet
December 6, 2010
Naos Raptor 6A: Non-isolated DC-DC Power Modules
4.5 – 14Vdc input; 0.59Vdc to 6Vdc Output; 6A output current
Feature Descriptions
Feature Descriptions (continued)
Remote On/Off
Output Voltage Programming
The Naos Raptor 6A modules feature an On/Off pin with
positive logic for remote On/Off operation. If the On/Off
pin is not being used, leave the pin open (the module
will be ON, except for the -49 option modules where
leaving the pin open will cause the module to remain
OFF). The On/Off signal (VOn/Off) is referenced to
ground. During a Logic High on the On/Off pin, the
module remains ON. During Logic-Low, the module is
turned OFF.
The output voltage of the Naos Raptor 6A module can
be programmed to any voltage from 0.59dc to 6Vdc by
connecting a resistor between the Trim+ and GND pins
of the module. Certain restrictions apply on the output
voltage set point depending on the input voltage. These
are shown in the Output Voltage vs. Input Voltage Set
Point Area plot in Fig. 49. The Upper Limit curve shows
that for output voltages of 0.9V and lower, the input
voltage must be lower than the maximum of 14V. The
Lower Limit curve shows that for output voltages of 3.8V
and higher, the input voltage needs to be larger than the
minimum of 4.5V.
MODULE
VIN
16
10K
2.2K
ENABLE
2.2K
47K
47K
GND
Figure 48. Remote On/Off Implementation. Resistor
R1 is absent in the -49Z option module.
Overcurrent Protection
To provide protection in a fault (output overload)
condition, the unit is equipped with internal
current-limiting circuitry and can endure current limiting
continuously. At the point of current-limit inception, the
unit enters hiccup mode. The unit operates normally
once the output current is brought back into its specified
range. The average output current during hiccup is 10%
IO, max.
Input Voltage (v)
R1
100K
ON/OFF
14
30.1K
12
Upper Limit
10
8
6
4
Lower Limit
2
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
Output Voltage (V)
Figure 49. Output Voltage vs. Input Voltage Set
Point Area plot showing limits where the output
voltage can be set for different input voltages.
Without an external resistor between Trim+ and GND
pins, the output of the module will be 0.59Vdc. To
calculate the value of the trim resistor, Rtrim for a
desired output voltage, use the following equation:
Rtrim =
1.182
kΩ
(Vo − 0.591)
Overtemperature Protection
Rtrim is the external resistor in kΩ
To provide protection in a fault condition, these modules
are equipped with a thermal shutdown circuit. The unit
will shut down if the overtemperature threshold of 130ºC
is exceeded at the thermal reference point Tref. The
thermal shutdown is not intended as a guarantee that
the unit will survive temperatures beyond its rating.
Once the unit goes into thermal shutdown it will then
wait to cool before attempting to restart.
Vo is the desired output voltage
Table 2 provides Rtrim values required for some
common output voltages.
Input Undervoltage Lockout
At input voltages below the input undervoltage lockout
limit, the module operation is disabled. The module will
begin to operate at an input voltage above the
undervoltage lockout turn-on threshold.
LINEAGE POWER
14
Data Sheet
December 6, 2010
Naos Raptor 6A: Non-isolated DC-DC Power Modules
4.5 – 14Vdc input; 0.59Vdc to 6Vdc Output; 6A output current
Table 2
VO, set (V)
Rtrim (KΩ)
0.59
1.0
1.2
1.5
1.8
2.5
3.3
5.0
6.0
Open
2.89
1.941
1.3
0.978
0.619
0.436
0.268
0.219
By using a ±0.5% tolerance trim resistor with a TC of
±25ppm, a set point tolerance of ±1.5% can be achieved
as specified in the electrical specification. The POL
Programming Tool available at www.lineagepower.com
under the Design Tools section, helps determine the
required trim resistor needed for a specific output
voltage.
V IN(+)
V O(+)
Vout
ON/OFF
LOAD
TRIM
R trim
GND
Figure 50. Circuit configuration for programming
output voltage using an external resistor.
Voltage Margining
Output voltage margining can be implemented in the
Naos Raptor 6A modules by connecting a resistor,
Rmargin-up, from the Trim pin to the ground pin for
margining-up the output voltage and by connecting a
resistor, Rmargin-down, from the Trim pin to output pin for
margining-down. Figure 51 shows the circuit
configuration for output voltage margining. The POL
Programming Tool, available at www.lineagepower.com
under the Design Tools section, also calculates the
values of Rmargin-up and Rmargin-down for a specific output
voltage and % margin. Please consult your local
Lineage Power technical representative for additional
details.
LINEAGE POWER
15
Data Sheet
December 6, 2010
Naos Raptor 6A: Non-isolated DC-DC Power Modules
4.5 – 14Vdc input; 0.59Vdc to 6Vdc Output; 6A output current
Feature Descriptions (continued)
Vo
Rmargin-down
MODULE
Q2
Trim
Rmargin-up
presence of a 3A to 6A step change (50% of full load),
with an input voltage of 12V. Table 4 shows the
recommended values of RTUNE and CTUNE for different
values of ceramic output capacitors up to 1000uF, again
for an input voltage of 12V. The value of RTUNE should
never be lower than the values shown in Tables 3 and
4. Please contact your Lineage Power technical
representative to obtain more details of this feature as
well as for guidelines on how to select the right value of
external R-C to tune the module for best transient
performance and stable operation for other output
capacitance values.
VOUT
Rtrim
RTUNE
Q1
MODULE
GND
CTUNE
Figure 51. Circuit Configuration for margining
Output voltage.
TRIM
GND
RTrim
Monotonic Start-up and Shutdown
The Naos Raptor 6A modules have monotonic start-up
and shutdown behavior for any combination of rated
input voltage, output current and operating temperature
range.
Tunable LoopTM
The Naos Raptor 6A modules have a new feature that
optimizes transient response of the module called
TM
Tunable Loop . External capacitors are usually added
to improve output voltage transient response due to
load current changes. Sensitive loads may also require
additional output capacitance to reduce output ripple
and noise. Adding external capacitance however
affects the voltage control loop of the module, typically
causing the loop to slow down with sluggish response.
Larger values of external capacitance could also cause
the module to become unstable.
To use the additional external capacitors in an optimal
TM
manner, the Tunable Loop feature allows the loop to
be tuned externally by connecting a series R-C between
the VOUT and TRIM pins of the module, as shown in
Fig. 52. This R-C allows the user to externally adjust
the voltage loop feedback compensation of the module
to match the filter network connected to the output of
the module.
Figure. 52. Circuit diagram showing connection of
RTUME and CTUNE to tune the control loop of the
module.
Table 3. Recommended values of RTUNE and CTUNE to
obtain transient deviation of 2% of Vout for a 3A
step load with Vin=12V.
Vout
5V
3.3V
2.5V
1.8V
1.2V
0.69V
2x47μF +
330μF
Cext 2x47μF 3x47μF 4x47μF
330μF 4x330μF
Polymer
Polymer Polymer
RTUNE
100
75
47
47
47
47
CTUNE
12nF
27nF
39nF
100nF
220nF
330nF
ΔV
81mV
57mV
43mV
27mV
24mV
11mV
Table 4. General recommended values of of RTUNE
and CTUNE for Vin=12V and various external ceramic
capacitor combinations.
Cext
1x47μF 2x47μF 4x47μF 10x47μF 20x47μF
RTUNE
150
100
47
47
47
CTUNE
10nF
12nF
39nF
68nF
82nF
Recommended values of RTUNE and CTUNE are given in
Tables 3 and 4. Table 3 lists recommended values of
RTUNE and CTUNE in order to meet 2% output voltage
deviation limits for some common output voltages in the
LINEAGE POWER
16
Data Sheet
December 6, 2010
Naos Raptor 6A: Non-isolated DC-DC Power Modules
4.5 – 14Vdc input; 0.59Vdc to 6Vdc Output; 6A output current
Thermal Considerations
Power modules operate in a variety of thermal
environments; however, sufficient cooling should be
provided to help ensure reliable operation.
Considerations include ambient temperature, airflow,
module power dissipation, and the need for increased
reliability. A reduction in the operating temperature of
the module will result in an increase in reliability. The
thermal data presented here is based on physical
measurements taken in a wind tunnel. . The test set-up
is shown in Figure 53. The preferred airflow direction
for the module is in Figure 54.
Wind Tunnel
Power Module
76.2
[3.0]
7.24
[0.285]
Probe Location
for measuring
airflow and
ambient
temperature
Air
Flow
Figure 53. Thermal Test Set-up.
The thermal reference point, Tref used in the
specifications of thermal derating curves is shown in
Figure 54. For reliable operation this temperature
should not exceed 120ºC.
The output power of the module should not exceed the
rated power of the module (Vo,set x Io,max).
Please refer to the Application Note “Thermal
Characterization Process For Open-Frame BoardMounted Power Modules” for a detailed discussion of
thermal aspects including maximum device
temperatures
LINEAGE POWER
Figure 54. Tref Temperature measurement location.
Post solder Cleaning and Drying
Considerations
50.8
[2.00]
PWBs
Airflow Direction
Post solder cleaning is usually the final circuit-board
assembly process prior to electrical board testing. The
result of inadequate cleaning and drying can affect both
the reliability of a power module and the testability of the
finished circuit-board assembly. For guidance on
appropriate soldering, cleaning and drying procedures,
refer to Board Mounted Power Modules: Soldering and
Cleaning Application Note.
Through-Hole Lead-Free Soldering
Information
The RoHS-compliant through-hole products use the
SAC (Sn/Ag/Cu) Pb-free solder and RoHS-compliant
components. They are designed to be processed
through single or dual wave soldering machines. The
pins have an RoHS-compliant finish that is compatible
with both Pb and Pb-free wave soldering processes. A
maximum preheat rate of 3°C/s is suggested. The wave
preheat process should be such that the temperature of
the power module board is kept below 210°C. For Pb
solder, the recommended pot temperature is 260°C,
while the Pb-free solder pot is 270°C max. Not all
RoHS-compliant through-hole products can be
processed with paste-through-hole Pb or Pb-free reflow
process. If additional information is needed, please
consult with your Lineage Power technical
representative for more details.
17
Data Sheet
December 6, 2010
Naos Raptor 6A: Non-isolated DC-DC Power Modules
4.5 – 14Vdc input; 0.59Vdc to 6Vdc Output; 6A output current
Mechanical Outline
Dimensions are in millimeters and (inches).
Tolerances: x.x mm ± 0.5 mm (x.xx in. ± 0.02 in.) [unless otherwise indicated]
x.xx mm ± 0.25 mm (x.xxx in ± 0.010 in.)
Front View
Side View
H = 4.8 [0.19]
L = 3.29 [0.13]
Pin out
LINEAGE POWER
Pin
Function
1
On/Off
2
VIN
3
GND
4
Vout
5
Trim+
18
Data Sheet
December 6, 2010
Naos Raptor 6A: Non-isolated DC-DC Power Modules
4.5 – 14Vdc input; 0.59Vdc to 6Vdc Output; 6A output current
Recommended Pad Layout
Dimensions are in millimeters and (inches).
Tolerances: x.x mm ± 0.5 mm (x.xx in. ± 0.02 in.) [unless otherwise indicated]
x.xx mm ± 0.25 mm (x.xxx in ± 0.010 in.)
LINEAGE POWER
19
Data Sheet
December 6, 2010
Naos Raptor 6A: Non-isolated DC-DC Power Modules
4.5 – 14Vdc input; 0.59Vdc to 6Vdc Output; 6A output current
Ordering Information
Please contact your Lineage Power Sales Representative for pricing, availability and optional features.
Table 5. Device Codes
Device Code
Input
Voltage Range
Output
Voltage
Output
Current
On/Off
Logic
Connector
Type
Comcodes
NSR006A0X4Z
4.5 – 14Vdc
0.59 – 6Vdc
6A
Positive
SIP
CC109130894
NSR006A0X4-49Z*
4.5 – 14Vdc
0.59 – 6Vdc
6A
Positive
SIP
CC109138194
Z refers to RoHS-compliant product.
* Special codes, consult factory before ordering
Table 6. Device Options
Option
Suffix
Long Pins
5.08 mm ± 0.25 mm
[0.2 ± 0.010 in.]
5
Asia-Pacific Headquarters
Tel: +86.021.54279977*808
World Wide Headquarters
Lineage Power Corporation
601 Shiloh Road, Plano, TX 75074, USA
+1-888-LINEAGE(546-3243)
(Outside U.S.A.: +1-972-244-WATT(9288))
www.lineagepower.com
e-mail: [email protected]
Europe, Middle-East and Africa Headquarters
Tel: +49.89.878067-280
India Headquarters
Tel: +91.80.28411633
Lineage Power reserves the right to make changes to the product(s) or information contained herein without notice. No liability is assumed as a result of their use or
application. No rights under any patent accompany the sale of any such product(s) or information.
Lineage Power DC-DC products are protected under various patents. Information on these patents is available at www.lineagepower.com/patents.
© 2010 Lineage Power Corporation, (Plano, Texas) All International Rights Reserved.
LINEAGE POWER
20
Document No: DS06-125 ver. 1.12
PDF name: NSR006A0X_ds.pdf