4.0-11.0 GHz GaAs MMIC Buffer Amplifier, QFN B1007-QT March 2010 - Rev 13-Mar-10 Features Excellent Transmit LO/Output Buffer Stage 3x3mm, QFN 23.0 dB Small Signal Gain +19.0 dBm P1dB Compression Point 4.5 dB Noise Figure Variable Gain with Adjustable Bias 100% RF, DC and Output Power Testing General Description Mimix Broadband’s two stage 4.0-11.0 GHz GaAs MMIC buffer amplifier has a small signal gain of 23.0 dB with a +20.0 dBm P1dB output compression point. The device also provides variable gain regulation with adjustable bias. The device is ideally suited as an LO or RF buffer stage with broadband performance at a very low cost. The device comes in an RoHS compliant 3x3mm QFN surface mount package offering excellent RF and thermal properties. This device is well suited for Microwave and Millimeter-wave Point-to-Point Radio, LMDS, SATCOM and VSAT applications. Absolute Maximum Ratings Supply Voltage (Vd) Supply Current (Id1) Gate Bias Voltage (Vg) Input Power (Pin) Storage Temperature (Tstg) Operating Temperature (Ta) Channel Temperature (Tch) ESD Min. - Machine Model (MM) ESD Min. - Human Body Model (HBM) MSL Level +4.3 VDC 200 mA 0V +20.0 dBm -65 to +165 ºC -55 to +85 ºC 150 ºC Class A Class 1A MSL1 Channel temperature affects a device's MTTF. It is recommended to keep channel temperature as low as possible for maximum life. Electrical Characteristics (Ambient Temperature T = 25 oC) Parameter Frequency Range (f ) Input Return Loss (S11) Output Return Loss (S22) Small Signal Gain (S21) Gain Flatness ( S21) Reverse Isolation (S12) Noise Figure Output Power for 1dB Compression (P1dB) Saturated Output Power (Psat) Output IP3 (OIP3) Drain Bias Voltage (Vd) Gate Bias Voltage (Vg) Supply Current (Id) (Vd=4.0V, Vg2=-0.5V Typical) Units GHz dB dB dB dB dB dB dBm dBm dBm VDC VDC mA Min. 4.0 -1.0 - Typ. 20.0 12.0 23.0 +/-1.5 50.0 4.5 +19.0 +21.0 31 +4.0 -0.35 100 Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Max. 11.0 +4.0 -0.1 130 Page 1 of 6 Characteristic Data and Specifications are subject to change without notice. ©2010 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 4.0-11.0 GHz GaAs MMIC Buffer Amplifier, QFN B1007-QT March 2010 - Rev 13-Mar-10 Buffer Amplifier Measurements XB1007-QT: S11 vs Frequency Vd=4V,Id=100mA 0 XB1007-QT: S21 vs Frequency Vd=4V,Id=100mA 26 24 -5 22 20 18 16 S21 (dB) S11 (dB) -10 -15 -20 14 12 10 -25 8 -30 4 6 2 -35 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 1 2 3 4 5 6 Frequency (GHz) XB1007-QT: S12 vs Frequency Vd=4V,Id=100mA 0 7 8 9 10 11 12 13 14 Frequency (GHz) XB1007-QT: S22 vs Frequency Vd=4V,Id=100mA 0 -10 -5 -30 S22 (dB) S12 (dB) -20 -40 -50 -10 -15 -60 -20 -70 -80 1 2 3 4 5 6 7 8 9 10 11 12 13 14 -25 1 Frequency (GHz) 3 4 5 6 7 8 9 10 11 12 13 14 Frequency (GHz) XB1007-QT: P1dB vs Frequency Vd=4V, Id=130mA 30 XB1007-QT: Psat vs Frequency Vd=4V, Id=130mA 30 28 28 26 26 24 24 22 Psat (dBm) P1dB (dBm) 2 20 18 16 '-40C '+25C '+85C 14 22 20 18 '-40C '+25C '+85C 16 14 12 12 10 4 5 6 7 8 Frequency (GHz) 9 10 11 10 4 5 6 7 8 9 10 11 Frequency (GHz) Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 2 of 6 Characteristic Data and Specifications are subject to change without notice. ©2010 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 4.0-11.0 GHz GaAs MMIC Buffer Amplifier, QFN B1007-QT March 2010 - Rev 13-Mar-10 Buffer Amplifier Measurements (cont.) XB1007-QT, Vd = 4V, Id = 90 mA, Pin = -15dBm: OIP3 vs Frequency XB1007-QT, Pin = -15dBm: OIP3 vs Gain 35 35 30 30 OIP3 (dBm) OIP3 (dBm) 25 25 20 20 15 4 GHz 10 6 GHz 15 8 GHz 5 10 4 5 6 7 8 9 10 10 GHz 0 6 8 10 12 14 16 Frequency (GHz) XB1007-QT, Pin = -15dBm: OIP3 vs Current 35 18 20 22 24 26 Gain (dB) XB1007-QT, Vd = 4V, Id = 100mA: Noise Figure over Temperature 10 9 30 8 Noise Figure (dB) OIP3 (dBm) 25 20 4 GHz 15 6 GHz 10 8 GHz 5 10 GHz 0 7 6 5 4 3 25 C 2 50 C 1 75 C 0 0 20 40 60 80 Drain Current (mA) 100 120 140 4 5 6 7 8 9 10 11 12 13 14 15 Frequency (GHz) Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 3 of 6 Characteristic Data and Specifications are subject to change without notice. ©2010 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 16 4.0-11.0 GHz GaAs MMIC Buffer Amplifier, QFN B1007-QT March 2010 - Rev 13-Mar-10 Package Dimensions / Layout (Note: Engineering designator is 8MPA0811) Functional Block Diagram gnd gnd gnd VD 1 6 1 5 1 4 1 3 Pin Designations 1 12 gnd 2 11 RF Out gnd 3 10 gnd gnd 4 9 gnd gnd RF In 5 6 7 8 VG gnd gnd gnd Pin Number Pin Name Pin Function Nominal Value 1 GND Ground RF In RF Input 2 3-4 GND Ground -0.5V 5 VG Gate Bias 6-10 GND Ground RF Out RF Output 11 12 GND Ground 4.0V, 100 mA 13 VD Drain Bias 14-16 GND Ground Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 4 of 6 Characteristic Data and Specifications are subject to change without notice. ©2010 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 4.0-11.0 GHz GaAs MMIC Buffer Amplifier, QFN B1007-QT March 2010 - Rev 13-Mar-10 App Note [1] Biasing - The device provides variable gain with adjustable bias regulation. For optimum linearity performance, it is recommended to bias this device at Vd=4V with Id=100 mA. It is also recommended to use active biasing to control the drain currents because this gives the most reproducible results over temperature or RF level variations. Depending on the supply voltage available and the power dissipation constraints, the bias circuit may be a single transistor or a low power operational amplifier, with a low value resistor in series with the drain supply used to sense the current. The gate of the pHEMT is controlled to maintain correct drain current and thus drain voltage. The typical gate voltage needed to do this is -0.5V. Typically the gate is protected with Silicon diodes to limit the applied voltage. Also, make sure to sequence the applied voltage to ensure negative gate bias is available before applying the positive drain supply. MTTF Graphs These numbers were calculated based on accelerated life test information and thermal model analysis received from the fabricating foundry. XB1007-QT-0G00: MTTF hours vs. Package Base Temperature 1.0E+15 1.0E+14 Vdd = 4 V, Idd = 100 mA 1.0E+13 Vdd = 4 V, Idd = 130 mA MTTF (hours) 1.0E+12 1.0E+11 1.0E+10 1.0E+09 1.0E+08 1.0E+07 1.0E+06 1.0E+05 1.0E+04 20 30 40 50 60 70 80 90 100 110 120 Package Base Temp (ºC) XB1007-QT-0G00: Tch (max) vs. Package Base Temperature 220 200 Tch_max (ºC) 180 160 140 120 100 Vdd = 4 V, Idd = 100 mA Vdd = 4 V, Idd = 130 mA 80 60 20 30 40 50 60 70 80 90 100 110 120 Package Base Temp (ºC) Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 5 of 6 Characteristic Data and Specifications are subject to change without notice. ©2010 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 4.0-11.0 GHz GaAs MMIC Buffer Amplifier, QFN B1007-QT March 2010 - Rev 13-Mar-10 Handling and Assembly Information CAUTION! - Mimix Broadband MMIC Products contain gallium arsenide (GaAs) which can be hazardous to the human body and the environment. For safety, observe the following procedures: • Do not ingest. • Do not alter the form of this product into a gas, powder, or liquid through burning, crushing, or chemical processing as these byproducts are dangerous to the human body if inhaled, ingested, or swallowed. • Observe government laws and company regulations when discarding this product. This product must be discarded in accordance with methods specified by applicable hazardous waste procedures. Life Support Policy - Mimix Broadband's products are not authorized for use as critical components in life support devices or systems without the express written approval of the President and General Counsel of Mimix Broadband. As used herein: (1) Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. (2) A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Package Attachment - This packaged product from Mimix Broadband is provided as a rugged surface mount package compatible with high volume solder installation. Vacuum tools or other suitable pick and place equipment may be used to pick and place this part. Care should be taken to ensure that there are no voids or gaps in the solder connection so that good RF, DC and ground connections are maintained. Voids or gaps can eventually lead not only to RF performance degradation, but reduced reliability and life of the product due to thermal stress. Typical Reflow Profiles Reflow Profile Ramp Up Rate Activation Time and Temperature Time Above Melting Point Max Peak Temperature Time Within 5 ºC of Peak Ramp Down Rate SnPb 3-4 ºC/sec 60-120 sec @ 140-160 ºC 60-150 sec 240 ºC 10-20 sec 4-6 ºC/sec Pb Free 3-4 ºC/sec 60-180 sec @ 170-200 ºC 60-150 sec 265 ºC 10-20 sec 4-6 ºC/sec Factory Automation and Identification Mimix Designator Package Type -QT QFN (3x3mm) Component Orientation: Number of leads offered W Tape Width P1 Component Pitch P0 Hole Pitch Reel Diameter Units per Reel 16 12mm 8mm 4mm 329mm (13in) 2000 Parts are to be oriented with the PIN 1 closest to the tape's round sprocket holes on the tape’s trailing edge. Note: Tape and Reel packaging is ordered with a -000T suffix. Package is available in 500 unit reels through designated sales channels. Minimum order quantities should be discussed with your local sales representative. Mimix Lead-Free RoHS Compliant Program - Mimix has an active program in place to meet customer and governmental requirements for eliminating lead (Pb) and other environmentally hazardous materials from our products. All Mimix RoHS compliant components are form, fit and functional replacements for their non-RoHS equivalents. Lead plating of our RoHS compliant parts is 100% matte tin (Sn) over copper alloy and is backwards compatible with current standard SnPb low-temperature reflow processes as well as higher temperature (260°C reflow) “Pb Free” processes. Ordering Information Part Number for Ordering Description XB1007-QT-0G00 XB1007-QT-0G0T XB1007-QT-EV1 Matte Tin plated RoHS compliant 3x3 16L QFN surface mount package in bulk quantity Matte Tin plated RoHS compliant 3x3 16L QFN surface mount package in tape and reel XB1007-QT evaluation boardd C a u t i o n : E S D S e n s i t i ve Appropriate precautions in handling, packaging and testing devices must be observed. Proper ESD procedures should be followed when handling this device. Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 6 of 6 Characteristic Data and Specifications are subject to change without notice. ©2010 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws.