PETERMANN SMD

FEATURES
PETERMANN
TECHNIK
- HIGH RELIABILITY FOR LOW COST
Time & Frequency Components
- SMALL DIMENSIONS
- AVAILABLE WITH SUPPLY VOLTAGE OF 2.6 VOLT
- LOW POWER CONSUMPTION
- NEW STANDARD FOR SMALL LOW COST SMD-VCTCXO'S AND SMD-TCXO's
- CHEAPEST AVAILABLE SMD-VCTCXO AND SMD-TCXO IN CERAMIC PACKAGE
SMD-VCTCXO-0507
SMD-TCXO-0507
PACKAGE
CERAMIC PACKAGE 7 x 5 x 1.9 mm
10.000 MHz ~ 28.000 MHz
FREQUENCY RANGE
10.000 MHz; 10.245 MHz; 12.800 MHz; 13.000 MHz;
STANDARD FREQUENCIES
13.5625 MHz; 14.400 MHz; 15.360 MHz; 16.800 MHz;
19.200 MHz; 19.440 MHz; 19.800 MHz; 20.000 MHz
MAXIMUM OPERATING TEMPERATURE RANGE
-40/+85°C
-30/+85°C
STANDARD OPERATING TEMPERATURE RANGE
STORAGE TEMPERATURE RANGE
-40/+85°C
2.6 ~ 5.5 VDC
SUPPLY VOLTAGE RANGE
STANDARD SUPPLY VOLTAGES
3.0 VDC +-5% / 3.3 VDC +-5% / 5.0 VDC +-5%
CURRENT CONSUMPTION
2 mA MAX. (LOAD 10 kΩ / 10 pF)
+-0.5 ppm @ 25°C +-2 °C
INITIAL FREQUENCY ACCURACY
+-2.5 ppm max. (-30/+85°C refered to +25°C)
VS. TEMPERATURE
FREQUENCY VS. AGING
+-1 ppm max. first year
STABILITY
+-0.3 ppm max. (3.0 VDC +-5%)
VS. VOLTAGE CHANGE
VS. LOAD CHANGE
+-0.3 ppm max. (10 kΩ +-10% / 10 pF +-10%)
FREQUENCY CHANGE AFTER REFLOW
+-1 ppm max.
10 kΩ / 10 pF
OUTPUT LOAD
OUTPUT VOLTAGE
0.8 ~ 1.0 Vp-p MIN.
OUTPUT SIGNAL
CLIPPED SINE WAVE
FREQUENCY TUNING RANGE
+-4 to +-16 ppm
FREQUENCY TUNING BY EXTERNAL VOLTAGE
1.5 VDC +-1 VDC (or depending the supply voltage)
HARMONICS DISTORTION
-8 dBc MAX. (-12 dBc TYP.)
PHASE NOISE
-120 dBc/Hz @ 1 kHz (-130 dBc TYP.)
SERIES
SMD-TCXO-0507
SMD-VCTCXO-0507
PIN 1
GROUND
VOLTAGE CONTROL
PIN 2
GROUND
GROUND
PIN 3
OUTPUT SIGNAL
OUTPUT SIGNAL
PIN
PIN
4
SUPPLY
VOLTAGE
SUPPLY
VOLTAGE
CONNECTION
PIN 5
NOT CONNECT
NOT CONNECT
PIN 6
NOT CONNECT
NOT CONNECT
PIN 7
NOT CONNECT
NOT CONNECT
PIN 8
NOT CONNECT
NOT CONNECT
DELIVERY FORM
TAPE AND REEL
MARKING
JYEG + FREQUENCY
MANUFACTURER
TJE / CHINA (ISO-9001/14001 qualified)
ORDERING CODE FOR SMD-VCTCXO
SMD-VCTCXO-0507-FREQUENCY-T
ORDERING CODE FOR SMD-TCXO
SMD-TCXO-0507-FREQUENCY-T
OTHER PARAMETERS ARE AVAILABLE ON REQUEST / CREATE HERE YOUR SPECIFICATION
Page 1 / 4
PETERMANN-TECHNIK GmbH | Amselweg 8 | D-86916 Kaufering
Fon: 00 49 (0) 81 91 / 30 53 95 | Fax: 00 49 (0) 81 91 / 30 53 97
http://www.petermann-technik.de | [email protected]
SERIES
SMD-VCTCXO
SMD-TCXO
RECOMMENDED LAYOUT
Page 2 / 4
PETERMANN
TECHNIK
Time & Frequency Components
TEST CIRCUIT
*2
*3
A
#4
VCC
0.01uF
#3
ZL
TOP VIEW
#1
#2
0.01uF
Vcont
ZL = Load Impedance *
* Includes all stray and probe capacitance
* ZL = 10 pF // 10 KOhm
*2 Frequency Counter
*3 Oscilloscope
Page 3 / 4
PETERMANN-TECHNIK GmbH | Amselweg 8 | D-86916 Kaufering
Fon: 00 49 (0) 81 91 / 30 53 95 | Fax: 00 49 (0) 81 91 / 30 53 97
http://www.petermann-technik.de | [email protected]
Solder Reflow Profile:
Critical Zone
TL to Tp
Tp
Ramp-down
Ramp-up
Temperature(T)
TL
Ts Max
Ts Min
tL
Ts Preheat
t 25℃ to Peak
tp
Time (t)
High Temperature Infrared /Convection
Note:Temperature shown are applied to body of device
Ts max to TL(Ramp-up Rate)
3°C/second max.
Preheat
Temperature Min(Ts Min)
Temperature Typical( Ts Typ)
Temperature Max.(Ts Max)
Time(ts)
150°C
175°C
200°C
60-180 seconds
Ram-up Rate(TL to Tp)
3°C/second Max
Time Maintained Above:
--Temperature(TL)
--Time(TL)
217°C
60-150 seconds
Peak Temperature (Tp)
260°C max.
seconds
Target Peak Temperature(Tp Target)
250°C+0/-5°C
Time within 5℃ of actual peak(tp)
Ramp-down Rate
Tune 25℃ to Peak Temperature(t)
Moisture Sensitivity Level
for
10
20-40 seconds
6°C/seconds Max
8 minutes Max
Level 1
High Temperature Manual Soldering
Note:Temperature shown are applied to body of device
260°C max. for 5 seconds max., 2 times max.
Page 4 / 4