HIGH EFFICIENCY RECTIFIER 1N4001G THRU 1N4007G FEATURES • • • • • DO-41 Glass passivated chip junction Low forward voltage drop Low reverse leakage High forward surge current capability High temperature soldering guaranteed 260℃/10 secods,0.375”(9.5mm)lead length at 5 lbs(2.3kg) tension 1.0(25.4) MIN. DIA. .205(5.2) .166(4.2) MECHANICAL DATA • • • • • • .034(0.9) .028(0.7) Case: Transfer molded plastic Epoxy: UL94V-0 rate flame retardant Polarity: Color band denotes cathode end Lead: Plated axial lead, solderable per MIL-STD-202E method 208C Mounting position: Any Weight: 0.012ounce, 0.33 grams .107(2.7) DIA. .080(2.0) 1.0(25.4) MIN. Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS • • • Ratings at 25℃ambient temperature unless otherwise specified Single Phase, half wave, 60Hz, resistive or inductive load For capacitive load derate current by 20% 1N 1N 1N 1N 1N 1N 1N SYMBOLS 4001G 4002G 4003G 4004G 4005G 4006G 4007G Maximum Repetitive Peak Reverse Voltage VRRM 50 100 200 400 600 800 1000 Maximum RMS Voltage VRMS 35 70 140 280 420 560 700 Maximum DC Blocking Voltage VDC 50 100 200 400 600 800 1000 Maximum Average Forward Rectified Current(FIG.1) 0.375”(9.5mm) lead length at T A=75℃ Peak Forward Surge Current 8.3mS single half sine wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage at 1.0A Maximum DC Reverse Current at Rated DC Blocking Voltage at TA = 25℃ TA = 125℃ Maximum Full Load Reverse Current, full cycle Average 0.375(9.5mm) lead length at TL=75℃ Typical Junction Capacitance (NOTE 1) Typical Thermal Resistance (NOTE 2) Operating and Storage Temperature Range UNITS Volts Volts Volts I(AV) 1.0 Amp IFSM 30 Amps VF 1.1 5.0 50 Volts IR(AV) 30 µA CJ RθJA TJ,TSTG 15 50 -55 to +150 ℃/W IR Notes: 1.Measured at 1.0MHz and applied reverse voltage of 4.0 Volits. 2. Thermal Resistance from Junction to Ambient at. 375”(9.5mm)lead length, P.C. board mounted. Web Site: WWW.PS-PFS.COM µA pF ℃ HIGH EFFICIENCY RECTIFIER 1N4001G THRU 1N4007G RATING AND CHRACTERISTIC CURVES IN4001G THRU IN4007G FIG.1-TYPICAL FORWARD CURRENT DERATING CURVE FIG.2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 0.8 0.6 0.4 Single Phase Half Wave 60Hz Resistive or Inductive Load 0.375(9.5mm) Lead Length 0.2 30 CURRENT, (A) PEAK FORWARD SURGE 1.0 (A) AVERAGE FORWARD CURRENT, 1.2 8.3ms Single Half Sine-Wave (JEDEC Method) T= T jmax 20 10 0 0 25 50 100 75 125 175 150 1 Cycle 0 AMBIENT TEMPERATURE, (° C) 2 1 4 6 8 10 40 20 60 100 NUMBER OF CYCLES AT 60 Hz FIG.4-TYPICAL REVERSE CHARACTERISTICS FIG.3-TYPICAL INSTANTANEOUS 20 FORWARD CHARACTERISTICS 10 INSTANTANEOUS REVERSE CURRENT, (μA) 10 1.0 (A) INSTANTANEOUS FORWARD CURRENT, 20 0.1 TJ =25° C Pulse Width=300us 1% Duty Cycle 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 TJ =125° C 1.0 0.1 TJ =25° C 0.01 0 INSTANTANEOUS FORWARD VOLTAGE,(V) 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) FIG.5-TYPICAL JUNCTION CAPACITANCE CAPACITANCE,(pF) 100 10 TJ =25° C f=1MHz Vsig=50mVp-p 1 0.1 1.0 10 100 REVERSE VOLTAGE,(V) Web Site: WWW.PS-PFS.COM 120 140