RF1336D ® • • • • Ideal Front-End Filter for European Wireless Receivers Low-Loss, Coupled-Resonator Quartz Design Simple External Impedance Matching Complies with Directive 2002/95/EC (RoHS) Pb 868.35 MHz SAW Filter The RF1336D is a low-loss, compact, and economical surface-acoustic-wave (SAW) filter designed to provide front-end selectivity in 868.35 MHz receivers. Receiver designs using this filter include superhet with 10.7 MHz or 500 kHz IF, direct conversion and superregen. Typical applications of these receivers are wireless remote-control and security devices operating in Europe under ETSI I-ETS 300 220, in Germany under FTZ 17 TR 2100, in the United Kingdom under DTI MPT 1340 (for automotive only), in France under PTT Specifications ST/PAA/TPA/AGH/1542, and in Scandinavia. This coupled-resonator filter (CRF) uses selective null placement to provide suppression, typically greater than 40 dB, of the LO and image spurious responses of superhet receivers with 10.7 MHz IF. RFM’s advanced SAW design and fabrication technology is utilized to achieve high performance and very low loss with simple external impedance matching. SM3838-8 Case 3.8 x 3.8 Electrical Characteristics Characteristic Center Frequency @ 25°C Absolute Frequency Insertion Loss 3 dB Bandwidth Attenuation: (relative to ILmin) Temperature Frequency Aging Impedance @ fC Sym Notes Minimum Units fC 1, 2, 3 868.35 1, 3 2.5 4.0 dB BW3 1, 2, 3 500 650 900 kHz 10 - 700 MHz 50 55 700 - 830 MHz 40 45 830 - 850 MHz 35 40 850 - 864.4 MHz 20 25 21 26 877.4 - 882.4 MHz 15 19 882.4 - 900 MHz 28 35 900 - 1000 MHz 40 1, 3 870.4 - 877.4 MHz Freq. Temp. Coefficient FTC Absolute Value during the First Year |fA| Input ZIN = RIN/CIN ZIN Output ZOUT = ROUT/COUT Maximum IL ZOUT Reel Size 7 Inch Reel Size 13 Inch MHz dB 45 3, 4 0.032 ppm/°C2 5 <±10 ppm/yr 1 Lid Symbolization (in addition to Lot and/or Date Codes) Standard Reel Quantity Typical 35.6Ω // 2.06pF 35.8Ω // 2.19pF 437 // YWWS 9 500 Pieces/Reel 3000 Pieces/Reel CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. Notes: 1. Unless noted otherwise, all measurements are made with the filter installed in the specified test fixture which is connected to a 50 Ω test system with VSWR ≤ 1.2:1. The test fixture L and C are adjusted for minimum insertion loss at the filter center frequency, fc. Note that insertion loss and bandwidth and passband shape are dependent on the impedance matching component values and quality. 2. The frequency fc is defined as the midpoint between the 3dB frequencies. 3. Where noted specifications apply over the entire specified operating temperature range of -40 to 105°C. 4. The turnover temperature, TO, is the temperature of maximum (or turnover) frequency, fo. The nominal frequency at any case temperature, Tc, may 5. 6. 7. 8. 9. be calculated from: f = fo [1 - FTC (To - Tc)2]. Frequency aging is the change in fc with time and is specified at +65°C or less. Aging may exceed the specification for prolonged temperatures above +65°C. Typically, aging is greatest the first year after manufacture, decreasing significantly in subsequent years. The design, manufacturing process, and specifications of this device are subject to change. One or more of the following U.S. Patents apply: 4,54,488, 4,616,197, and others pending. All equipment designs utilizing this product must be approved by the appropriate government agency prior to manufacture or sale. Tape and Reel Standard for ANSI / EIA 481. RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: [email protected] http://www.rfm.com RF1336D-031505 Page 1 of 2 868.35 MHz SAW Filter Absolute Maximum Ratings Rating Input Power Level DC Voltage Storage Temperature Operable Temperature Range Soldering Temperature 1 Input Ground 2 Input 3 Ground 4 Case Ground 5 Output Ground 6 Output 7 Ground 8 Case Ground 10 dBm 12 VDC °C -40 to +125 °C 260 °C A E C B 8 Electrical Connections Connection Units -40 to +125 (10 seconds / 5 cycles max.) Pin Value 8 1 7 H 7 1 2 6 6 2 3 5 5 3 G 4 4 F D Matching Circuit to 50Ω Ω Case Dimensions Dimension 7 12 nH 11 nH 6 Output A B C D E F G H 1 5 8 4 2 Input 3 Min 3.6 3.6 1.00 0.95 0.90 0.50 2.39 1.40 mm Nom 3.8 3.8 1.20 1.10 1.0 0.6 2.54 1.75 Max 4.0 4.0 1.40 1.25 1.10 0.70 2.69 2.05 Inches Nom 0.15 0.15 0.05 0.043 0.04 0.024 0.100 0.069 Min 0.14 0.14 0.04 0.037 0.035 0.020 0.090 0.055 Max 0.16 0.16 0.055 0.05 0.043 0.028 0.110 0.080 OPTIONAL Electrical Connections Pin 1 2 3 4 5 6 7 8 Connection Input Input Ground Ground Case Ground Output Output Ground Ground Case Ground Matching Circuit to 50Ω Ω 11 nH 7 6 12 nH Output RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. 5 1 8 4 Input 2 3 E-mail: [email protected] http://www.rfm.com RF1336D-031505 Page 2 of 2