SANKEN STR

STR-A6000 Series
Power IC for PWM Type Switching Power Supply
with Low Noise and Low Standby Power
■ General Descriptions
The STR-A6000 series products are power ICs for switching power supplies,
incorporating a power MOSFET and a current-mode type PWM controller IC. The low
standby power is accomplished by the automatic switching between the PWM operation in
normal operation and the burst-oscillation under light load conditions. The product
achieves high cost-performance power supply systems with few external components.
■ Features
Current-Mode Type PWM Control
Built-in Random Switching Function
DIP-8
The function reduces the EMI noise and enables a simplified (low-cost) EMI filter,
by the slight- random-change of PMW frequency fOSC.
Auto-Standby Function: The burst-oscillation enables the low standby power. Input Power PIN < 25mW at no load
Built-in Startup Circuit, enabling low power consumption
Brown-In / Brown-Out Function
The function enables the oscillation start/stop by externally rated input voltage and makes protections at low input
voltage.
Overcurrent Protection (OCP) with Built-in Input Compensation Circuit:
The protection has less AC input voltage dependency.
Overload Protection (OLP) with Built-in Delay Timer
High Speed Latch Release Function
The function releases the latch immediately at AC supply OFF, after the latch protection operation.
Bias-Assist Function, reducing Operating VCC voltage drop
The function improves the startup operation and makes a low VCC capacitor applicable.
Leading Edge Blanking Function
Slope Compensation Function
Built-in Avalanche Energy Guaranteed High-Voltage Power MOSFET
Various Protections
Overcurrent Protection (OCP)--------------------------------- Pulse-by-Pulse
Overload Protection (OLP) ------------------------------------ Auto-Restart
Overvoltage Protection (OVP) -------------------------------- Latch Shutdown
Thermal Shutdown Protection (TSD) ------------------------ Latch Shutdown
■ Applications
Battery Chargers; Mobile Phones, Digital Cameras, Camcorders, Electric Shavers, Emergency/Inducement Lights etc.
Standby Power Supplies; LCD-TVs, PDP-TVs, Desk-Top PCs, LBPs, Audio Equipment, etc.
Small SMPSs; Ink Jet Printers, BD/DVD Players, CD Players, Set-Top-Boxes, etc.
Auxiliary Power Supplies for Controllers; Air Conditioners, Refrigerators, Washing Machines, Dish Washers, etc
■ Product Lineup
fosc
(kHz)
MOSFET
VDSS MIN (V)
RDS(ON) MAX
(Ω)
(Note 1)
POUT
230VAC/Universal
STR-A6051M
3.95
16W / 12W
STR-A6052M
2.8
20W / 16W
67
650
STR-A6053M
1.9
24W / 20W
STR-A6059H
6.0
10W / 8W
STR-A6062H
2.8
15W / 13W
100
700
STR-A6069H
6.0
10W / 8W
STR-A6079M
67
800
19.2
8W / 5W
Note 1: The maximum output power is derived from thermal specifications. The actual output power may be
available around 120 –140% of the above values, respectively, but may be limited by ON duty setting on
transformer design or lower output voltage.
Product No
2010/08
■ Typical Application Circuit
V OUT
VAC
GND
8
7
D/ST D/ST
5
Vcc
STR-A6000
FB/
S/OCP BR GND OLP
1
2 3
4
■ Typical Electrical Characteristics
STR-A6079M Efficiency & Input Power at Standby
Efficiency η-
- Output Power POUT
100VAC
Standby Power (POUT: 5W Power Supply)
100VAC
220VAC
250
90
PIN (mW)
70
60
Input Power
η(%)
80
Efficiency
220VAC
50
40
30
20
200
At No Load
Load
19.6mW
.6mW 100VAC
19
100VAC
20.0mW 220VAC
0VAC
150
100
50
0
0
2
Output Power
4
POUT (W)
6
0
50
100
150
Output Power POUT (mW)
Without Brown-IN/Brown-OUT Detection Resistor
Warning
The contents in this document are subject to changes, for improvement and other purposes, without notice.
Make sure that this is the latest version of the document before use.
The operation and circuit examples in this document are provided for reference purposes only. Sanken assumes no liability for violation of industrial property, intellectual property, or other rights of
Sanken or third parties, that stem from these examples.
The user must take responsibility for considering and determining which objects the products in this document are used with.
Although Sanken will continue to improve the quality and reliability of its products,
semiconductor products, by their nature, have certain fault and failure rates. The user must take responsibility for designing and checking to secure the device and system so that a part failure may not lead
to human injury, fire, damages, or other losses.
The contents in this document must not be transcribed or copied without Sanken’s written consent.
SANKEN ELECTRIC CO.,LTD.
2010/08