TX-704-0007-12M800000 TCXO Nominal frequency (f0) 12.8 MHz Frequency stabilities Parameter Over all (df/f0) vs. operating temp. range (df/f@25 °C) Additional information Temperature slope max: ±0.2ppm/°C Frequency stability Operating temp. range -4.6 to 4.6 ppm -0.28 to 0.28 ppm -40 ... 85 °C Value Condition Parameter initial tolerance (df/f0) -1 to 1 ppm vs. supply voltage change (df/f) -0.2 to 0.2 ppm vs. load change (df/f) -0.2 to 0.2 ppm vs. aging / 20 years (df/f) <± 2.5 ppm Holdover 24 h ± 0.32 ppm overall incl.: initial, temp.-40..+85°C, supply, load var. and aging 20 years @25 °C static; 3.3 V ±5 % static; Load ± 10 % @ 40 °C incl. temp. stab. -40...+85°C RF output Parameter Signal Load Fan out Rise Time Fall Time Duty cycle V Low V High Enable function Value Condition LVCMOS 15 pF ±10 % 3 < 5 ns < 5 ns 40 / 60 % x < 0.3 V x>3V Enable Function Pin 8 high open low @ 10 to 90 %Vout @ 90 to 10 %Vout @ 1.65 V output Pin 5 data data high tristate Supply voltage Parameter Supply voltage (Vs) Current consumption steady state Value Condition 3.3 V ± 5 % < 6 mA @ Vsnom & 25 °C Additional Parameters Parameter Typ. Phase Noise -97 -118 -140 -152 -153 -153 Parameter Max. Condition dBc/Hz@10Hz dBc/Hz@100Hz dBc/Hz@1000Hz dBc/Hz@10kHz dBc/Hz@100kHz dBc/Hz@1000kHz Value Condition Start-up time < 10 ms Additional information This SMD oscillator is designed only for pick and place/reflow soldering process. Manual soldering may damage the part and therefore not recommended for the mounting of this oscillator. Processing & Packing handling&processing note Additional environmental conditions Sealing test A nicht dicht (not hermetically sealed) Solderability J_STD_002B Cond A leaded/ Cond. B SMD 245°C (diving time 5±0.5s) Dip+Look with 8h damp treatment: solder wetting >95% Vectron International • Product Specifications TX-704-0007 www.vectron.com modified 2011-04-07 Index : 1 printed 2011-06-03 • page 1 of 4 TX-704-0007-12M800000 TCXO Absolute Maximum Ratings Parameter Min Operable temperature range Storage temperature range -40 -55 Typ Max Units 85 125 °C °C Condition Enclosure Type G290 Height 1.8 mm all units in mm Pin Connections Pin 1: I.C. Pin 3: I.C. Pin 5: RF-Output Pin 7: N.C. Pin 9: V_supply Marking TX-007 12M800 *VAYYWW * pin-1 marking 2: N.C. 4: GND 6: N.C. 8: Enable 10: N.C. Vectron International • Product Specifications TX-704-0007 www.vectron.com modified 2011-04-07 Index : 1 printed 2011-06-03 • page 2 of 4 TX-704-0007-12M800000 TCXO Reflow profile Profile Feature Pb-Free Assembly/Sn-Pb Assembly Average ramp-up rate (TL to Tp) 3°C/second max. Preheat -Temperature Min (Tsmin) 150°c -Temperature Min (Tsmax) 200°c -Time (min to max) (ts) 60-180 seconds Tsmax to TL - Ramp-up Rate 3°C/second max. Time maintainted above - Temperature (TL) 217°C - Time (tL) 60-150 seconds Peak Temperature (Tp) max 260°C Time within 5°C of actual Peak Temperature (tp) 20-40 seconds Ramp-down Rate 6°C/second max. Time 25°C to Peak Temperature 8 minutes max. Note: All temperatures refer to topside of the package, measured on the package body surface. Additional Information This SMD oscillator has been designed for pick and place reflow soldering. Vectron International • Product Specifications TX-704-0007 www.vectron.com modified 2011-04-07 Index : 1 printed 2011-06-03 • page 3 of 4 TX-704-0007-12M800000 TCXO Standard shipping method Tape width W [mm] Quantity per meter Quantity per reel P [mm] A [mm] B [mm] K [mm] 16 125 750 8 5.4 7.4 2.7 Notes: Unless otherwise stated all values are valid after warm-up time and refer to typical conditions for supply voltage, frequency control voltage, load, temperature (25°C). Subject to technical modification. Vectron International • Product Specifications TX-704-0007 www.vectron.com modified 2011-04-07 Index : 1 printed 2011-06-03 • page 4 of 4