3M™ Mini D Ribbon (MDR) Connectors .050″ IDC Wiremount Plug - Shielded 101 Series • Wiper-on-wiper contact for reliable repetitive plugging • MDR digital LCD interface as a 20 or 26 contact connector • IEEE 1284C Interface as a 36 contact connector • Accepts a wide variety of cable constructions including flat, round, twisted pair and twinax cables • Accepts a wide variety of shielded junction shells • Contacts: 14, 20, 26, 36, 40, 50, 68, 80 and 100 • See Regulatory Information Appendix (RIA) for chemical compliance information Date Modified: February 7, 2007 TS-0423-14 Sheet 1 of 3 Physical Insulation Material: Glass Reinforced Polyester Flammability: UL 94V-0 Body Color: Black Cover Color: Black, Gray Contact Material: Beryllium Copper Underplating: 80 μ″ [ 2.0 μm ] Nickel Wiping Area Plating: 30 μ″ [ 0.76 μm ] Min. Gold IDC Contacts Plating: Gold flash Shroud Material: Plating: Wire Accommodation Black Cover: Gray Cover: Steel Nickel 28 AWG Stranded, 30 AWG Solid (Insulation Diameter = 0.7 mm Max.) 26 AWG Solid (Insulation Diameter = 0.7 mm to 0.9 mm) Marking: 3M Logo and Part Number Electrical Current Rating: 1 A Insulation Resistance: > 1 × 108Ω at 500 VDC Withstanding Voltage: 500 VRMS for 1 Minute Environmental Temperature Rating: -20°C to +85°C UL File No.: E68080 3 Interconnect Solutions http://www.3M.com/interconnects/ 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3M™ Mini D Ribbon (MDR) Connectors .050″ IDC Wiremount Plug - Shielded 101 Series Dimensions Contact Quantity A B C D 14 .300 [ 7.62 ] 26 .600 [ 15.24 ] .54 [ 13.8 ] .72 [ 18.2 ] .58 [ 14.7 ] .84 [ 21.4 ] 1.02 [ 25.8 ] 50 1.200 [ 30.48 ] .88 [ 22.4 ] 1.44 [ 36.6 ] 1.62 [ 41.1 ] 1.48 [ 37.6 ] Cover Assembly Body (14, 26 and 50 positions) .21 [ 5.2 ] .025 [ 0.64 ] 0 Position (See Note 1) Last Position .050 [ 1.27 ] .126 [ 3.20 ] .13 [ 3.2 ] Position 1 (See Note 2) .189 [ 4.80 ] Position 3 Cover 1 Position 2 .06 [ 1.5 ] D 101XX .18 [ 4.5 ] .26 [ 6.6 ] .29 [ 7.4 ] .50 [ 12.7 ] C Body .13 [ 3.20 ] Cover 2 Position 1 Position 2 Position 3 .08 [ 2.0 ] .050 [ 1.27 ] .30 [ 7.5 ] .36 [ 9.1 ] .26 [ 6.5 ] Last Position .29 [ 7.3 ] Position 15° (See Notes) D A In c h B [m m ] T o le ra n c e U n le s s N o te d Notes: 1.Circle (0) position indicates #1 position in cable, when utilizing 0.025″ pitch flat cable. in c h 2.Triangle (∇) position indicates #2 position in cable, when utilizing 0.025″ pitch flat cable. Ordering Information (See page 3 for other sizes and assembly tools.) Interconnect Solutions http://www.3M.com/interconnects/ .0 0 ± .0 1 ± .0 0 5 .0 0 0 [ ] D im e n s io n s fo r R e fe re n c e O n ly 101XX-60X0EC Contact Quantity (See Table) Note: 100 pos = A0 Wiping Interface Plating: C = 30μ m [ 0.76 mm ] Min. Gold over Ni Wire Accommodation: 0 = Black Cover: 28 AWG Stranded, 30 AWG Solid 1 = Gray Cover: 26 AWG Solid (Available in 68 Contact Only, UL Pending) 3 .0 ± .1 IDC Plating: E = Gold Flash over Ni (App E1 & C1 apply) TS-0423-14 Sheet 2 of 3 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3M™ Mini D Ribbon (MDR) Connectors .050″ IDC Wiremount Plug - Shielded Contact Quantity 101 Series Dimensions A B C D 20 .450 [ 11.43 ] .69 [ 17.6 ] .87 [ 22.0 ] .73 [ 18.6 ] 36 .850 [ 21.59 ] 1.09 [ 27.8 ] 1.27 [ 32.2 ] 1.13 [ 28.7 ] 40 .950 [ 24.13 ] 1.19 [ 30.3 ] 1.37 [ 34.7 ] 1.23 [ 31.3 ] 68 1.650 [ 41.91 ] 1.89 [ 48.1 ] 2.07 [ 52.5 ] 1.93 [ 49.0 ] 80 1.950 [ 49.53 ] 2.16 [ 54.8 ] 2.37 [ 60.1 ] 2.23 [ 56.7 ] 100 2.450 [ 62.23 ] 2.66 [ 67.5 ] 2.87 [ 72.8 ] 2.73 [ 69.4 ] Cover Assembly .21 [ 5.33 ] Body (20, 36, 40, 68, 80 and 100 positions) .025 [ 0.64 ] 0 Position (See Note 1) .13 [ 3.30 ] .126 [ 3.20 ] Last Position .050 [ 1.27 ] .189 [ 4.80 ] .06 [ 1.5 ] Cover 1 D .29 [ 7.4 ] .26 [ 6.6 ] Position 3 Position 2 101XX Position 1 (See Note 2) .13 [ 3.20 ] .50 [ 12.7 ] Cover 2 C .08 [ 2.0 ] Body .18 [ 4.5 ] Position 2 Position 3 Position 1 .050 [ 1.27 ] .29 [ 7.3 ] .30 [ 7.5 ] .36 [ 9.1 ] .26 [ 6.5 ] D Last Position 15° Position In c h [m m ] (See Notes) T o le ra n c e U n le s s N o te d A B in c h Notes: 2.Triangle (∇) position indicates #2 position in cable, when utilizing 0.025″ pitch flat cable. .0 0 0 101XX-60X0EC Ordering Information Contact Quantity (See Table) Note: 100 pos = A0 Wiping Interface Plating: C = 30μ m [ 0.76 mm ] Min. Gold over Ni Wire Accommodation: 0 = Black Cover: 28 AWG Stranded, 30 AWG Solid 3: Assembly tools: 3M™ Hand Press Kit 3829 (68 1 = Gray Cover: 26 AWG Solid (Available in 68 Contact position & below). All Sizes: 3M™ Assembly Press Only, UL Pending) 10962-2000; 3M™ Lacing Fixture 10962-2000, 3M™ Cutting Unit 10961 & 3M™ Wire Clamp 10964-1 (14-50 pos.) or 3M™ Wire Clamp 10964-2 (68-100 pos.). Interconnect Solutions http://www.3M.com/interconnects/ .0 0 ± .0 1 ± .0 0 5 [ ] D im e n s io n s fo r R e fe re n c e O n ly 1.Circle (0) position indicates #1 position in cable, when utilizing 0.025″ pitch flat cable. 3 .0 ± .1 IDC Plating: E = Gold flash over Ni (App E1 & C1 apply) TS-0423-14 Sheet 3 of 3 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 Regulatory Information Appendix 3M Electronic Solutions Division/Interconnect EUROPE Appendix E1: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product is RoHS Compliant 2005/95/EC. “RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/ EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. Appendix E2: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is compliant by exemption under EU Commission Decision 2005/747/EC. “RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/ EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. Appendix E3: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as amended by Commission Decision 2005/618/EC. This product contains lead in the solder tail area in excess of the maximum concentration value allowed. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. Appendix E4: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product contains decaBDE in the insulating material in excess of the maximum concentration value allowed but is compliant by exemption under EU Commission Decision 2005/17/EC. “RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. RIA-2217-B CHINA Appendix C1: China RoHS Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the product or part does not contain any of the following substances in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. Appendix C2: China RoHS 20 Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the product Warranty stated below. Name and Content of Hazardous Substances or Elements Important Notice All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M. Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted. 3 Electronic Solutions Division 6801 River Place Blvd. Austin, TX 78726-9000 800/225-5373 www.3M.com/interconnects RIA-2217-B © 3M 2007