3M™ Mini D Ribbon (MDR) Connectors .050″ Surface Mount Right Angle Receptacle - Shielded 102 Series • Wiper-on-wiper contact for reliable repetitive plugging • Ultra-low signal skew for high data rate transmission • Interface latch design for connection stability • MDR digital LCD interface as a 20 or 26 contact connector • Contacts: 14, 20, 26, 40 and 50 • See Regulatory Information Appendix (RIA) for chemical compliance information Date Modified: November 13, 2007 TS-0755-C Sheet 1 of 3 Physical Insulation Material: Flammability: Color: Contact Material: Plating Underplating: Wiping Area: Solder Tail Plating: Shroud and Latch Hook Material: Plating: Grounding Flange Screw Lock Material: Plating: Marking: Glass Reinforced Polyester (PCT) UL 94V-0 Beige Copper Alloy 80 μ″ [ 2.0 μm ] Nickel 20 μ″ [ 0.50 μm ] Min. Gold Gold Flash over Nickel (RIA E1 & C1 apply) Steel Nickel Copper Alloy Tin 3M Logo and Part Number Electrical Current Rating: 1 A Insulation Resistance: > 5 × 108Ω at 500 VDC Withstanding Voltage: 500 VRMS for 1 Minute Environmental -55°C to +105°C Process Rating: 260°C (profile per J-STD-020C) Temperature Rating: UL File No.: E68080 3 Interconnect Solutions http://www.3M.com/interconnects/ 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3M™ Mini D Ribbon (MDR) Connectors .050″ Surface Mount Right Angle Receptacle - Shielded Contact Quantity 102 Series Dimensions A±.008 B±.006 C±.006 D±.006 E±.006 14 1.16 [ 29.5 ] .931 [ 23.64 ] .500 [ 12.70 ] .325 [ 8.26 ] .496 [ 12.6 ] 20 1.32 [ 33.4 ] 1.081 [ 27.45 ] .650 [ 16.51 ] .475 [ 12.07 ] .646 [ 16.4 ] 26 1.50 [ 38.2 ] 1.231 [ 31.26 ] .800 [ 20.32 ] .625 [ 15.88 ] .795 [ 20.2 ] 40 1.85 [ 47.1 ] 1.581 [ 40.15 ] 1.150 [ 29.21 ] .975 [ 24.77 ] 1.150 [ 29.2 ] 50 2.06 [ 52.4 ] 1.831 [ 46.50 ] 1.400 [ 35.56 ] 1.225 [ 31.12 ] 1.398 [ 35.5 ] A .025 [ 0.635 ] last position position 2 2X M2.5 Thread position below pos. 1 D position above last position .368 [ 9.35 ] position 1 .047 [ 1.20 ] .010 nom. [ 0.25 ] .394 [ 10.00 ] .187 [ 4.75 ] .203 [ 5.15 ] .19 [ 4.8 ] 2X .138 [ 3.5 ] E B 2X M2.5 Thread (see note in ordering info) Position 1 .248 [ 6.30 ] .189 [ 4.80 ] In c h [m m ] Position last position T o le ra n c e U n le s s N o ted C Positioning Boss (2x) in c h .0 .0 0 ± .1 ± .0 1 ± .0 05 .0 00 [ ] D im e n sio n s for R e fe re n ce O n ly Ordering Information 102XX-1210PE Contact Quantity (See Table) Note: Use ( M2.5x8 mm ) screws to mount to panel with max. thickness of .079 [ 2.0 ]. 3 Interconnect Solutions http://www.3M.com/interconnects/ TS-0755-C Sheet 2 of 3 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3M™ Mini D Ribbon (MDR) Connectors .050″ Surfacemount Right Angle Receptacle - Shielded 102 Series Recommended Board Layout Dimensions Contact Quantity A ± .002 B ± .002 C ± .002 14 .931 [ 23.64 ] .500 [ 12.70 ] .325 [ 8.26 ] 20 1.081 [ 27.45 ] .650 [ 16.51 ] .475 [ 12.07 ] 26 1.230 [ 31.26 ] .800 [ 20.32 ] .625 [ 15.88 ] (viewed from connector side) Solder Pads for Solder Tail (See below for more detail) center spacing C 40 1.581 [ 40.15 ] 1.150 [ 29.21 ] .975 [ 24.77 ] 50 1.831 [ 46.50 ] 1.400 [ 35.56 ] 1.225 [ 31.12 ] .165 [ 4.2 ] center spacing .0250 ± .0008 [ 0.64 ] .118 [ 3.0 ] 2x .122 [ 3.1 ] 2x .138 [ 3.5 ] 2x .256 [ 6.5 ] .187 max. [ 4.75 ] .088 [ 2.223 ] .0158 ± .0004 [ 0.40 ] .093 ± .004 [ 2.36 ] ∅ .110 ± .004 (2X) Screw Lock (see notes below) Lockstand Solder Pad Outline PCB Ref. Edge ∅ .079 + .004 (2X) - .000 Positioning Hole B A Solder Pad and Contact Numbering Detail (Pad numbers correspond to connector contact numbers shown on previous page) Notes: 14 Pos. 7 14 Last Pos. 6 13 5 12 4 11 3 1 2 10 9 8 Position (Bottom Row) PCB Ref. Edge 10 20 Pos. Last Pos. 20 19 7 8 9 18 17 5 6 16 15 1. Plated through mounting holes for .062″ [1.57] board thickness. 2. The connector should be fixed to the PCB by screws, tools or other means during the soldering process. To prevent soldering defects, the screws (M2.5) should not be tightened excessively. 3. The connector must be fixed to the PCB by board lock screws after soldering. The connector should be fixed to the panel with panel mount screws or jack sockets. See TS-0142 for mounting hardware. Connector Position (Top Row) 3 4 14 13 1 2 12 Connector Position (Top Row) 11 Position (Bottom Row) PCB Ref. Edge 26 Pos. 13 Last Pos. 26 25 24 9 8 23 22 21 7 6 5 4 3 2 Connector Position (Top Row) 1 20 19 18 17 16 15 14 Position (Bottom Row) PCB Ref. Edge 40 Pos. Last Pos. 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 Connector Position 1 Position (Bottom Row) 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 PCB Ref. Edge 50 Pos. Last Pos. 12 11 10 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 1 Connector Position Position (Bottom Row) PCB Ref. Edge Contact Quantity D E Recommended Panel Cut-out 14 .78 [ 19.9 ] .931 [ 23.64 ] Note: Panel thickness .079 [ 2.00 ] Max. 20 .94 [ 23.8 ] 1.081 [ 27.45 ] 26 1.09 [ 27.6 ] 1.231 [ 31.26 ] 40 1.44 [ 36.5 ] 1.581 [ 40.15 ] 50 1.69 [ 42.8 ] 1.830 [ 46.50 ] .319 ± .004 [ 8.1 ] R .060 [ 1.50 ] D ± .004 E ± .004 3 Interconnect Solutions http://www.3M.com/interconnects/ TS-0755-C Sheet 3 of 3 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 Regulatory Information Appendix 3M Electronic Solutions Division/Interconnect EUROPE Appendix E1: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product is RoHS Compliant 2005/95/EC. “RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. Appendix E2: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is compliant by exemption under EU Commission Decision 2005/747/EC. “RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. Appendix E3: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as amended by Commission Decision 2005/618/EC. This product contains lead in the solder tail area in excess of the maximum concentration value allowed. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. Appendix E4: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product contains decaBDE in the insulating material in excess of the maximum concentration value allowed but is compliant by exemption under EU Commission Decision 2005/717/EC. “RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. RIA-2217B-c Appendix E5: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product contains lead in excess of the maximum concentration value allowed but is compliant by exemption under Item 6 of the Annex to the Directive. “RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. CHINA Appendix C1: China RoHS Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the product or part does not contain any of the following substances in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. Appendix C2: China RoHS Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the product Warranty stated below. RIA-2217B-c Appendix C3: China RoHS Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the product Warranty stated below. Important Notice All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M. Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted. 3 3M Electronics Interconnect Products 6801 River Place Blvd. Austin, TX 78726-9000 U.S.A. 1-800-225-5373 www.3m.com/interconnects Please recycle. Printed in USA. © 3M 2007. All rights reserved. RIA-2217B-c 3M is a trademark of 3M Company.