SPECIFICATION FOR APPROVAL REF : PAGE: 1 PROD. NAME ABC'S DWG NO. SMD POWER INDUCTOR SQ0805□□□□L□-□□□ ABC'S ITEM NO. Ⅰ﹒CONFIGURATION & DIMENSIONS： Marking B 100 A D m/m B : 6.0±0.3 m/m C : 4.5±0.3 m/m C ' : 5.0±0.7 m/m D : 1.4 ref. m/m E : 3.4 ref. m/m F : 6.0 ref. m/m G : 5.0 ref. m/m H : 4.0 ref. m/m I : m/m 2.0 ref. I G I H F : 8.8±0.3 E D C' C Dot is start winding & inductance code A （PCB Pattern） Ⅱ﹒SCHEMATIC DIAGRAM： a b Ⅲ﹒MATERIALS： d a﹒Core：Ferrite DQ core b﹒Wire ：Enamelled copper wire (class F) c﹒Terminal：Cu/Sn d﹒Adhesive：Epoxy resin Peak Temp：260℃ max. Max time above 230℃ ：50sec max. Max time above 200℃ ：70sec max. e﹒Remark：Products comply with RoHS' requirements c Temperature Rising Area Preheat Area +4.0℃ / sec max. 150 ~ 200 ℃ / 60 ~ 120sec Reflow Area +2.0 ~ 4.0℃ / sec max. Forced Cooling Area -(1.0 ~ 5.0)℃ / sec max. Peak Temperature: 260℃ 250 a﹒Temp. rese ：40℃ max. b﹒Rated current：Base no temp. rise & △L / LOA=30% typ. c﹒Storage temp.：-40℃ ----+125℃ d﹒Operating temp.：-40℃----+105℃ e﹒Resistance to solder heat：260℃.10 secs. AE-001A 50sec max. Temperature ( ℃ ) Ⅳ﹒GENERAL SPECIFICATION： 230℃ 200 150 70sec max. 100 50 0 50 100 150 Time ( seconds ) 200 250 SPECIFICATION FOR APPROVAL REF : PAGE: 2 PROD. NAME ABC'S DWG NO. SMD POWER INDUCTOR SQ0805□□□□L□-□□□ ABC'S ITEM NO. Ⅴ﹒ELECTRICAL CHARACTERISITCS： RDC ( mΩ ) max. Irms (A) Isat (A) 200.0 4.50 9.00 12.00 1.20 ±20% 100.0 8.20 6.00 8.80 SQ08052R2ML□ -□□□ 2.20 ±20% 75.0 16.00 4.50 6.50 SQ08054R7ML□-□□□ 4.70 ±20% 35.0 35.00 3.00 4.20 SQ0805100ML□ -□□□ 10.00 ±20% 26.0 60.00 2.40 3.00 SQ0805150ML□ -□□□ 15.00 ±20% 19.0 90.00 2.00 2.40 SQ0805220ML□ -□□□ 22.00 ±20% 15.0 160.00 1.60 2.00 SQ0805330ML□ -□□□ 33.00 ±20% 10.0 185.00 1.20 1.60 SQ0805470ML□ -□□□ 47.00 ±20% 8.0 260.00 1.00 1.30 DWG No. Inductance ( µH ) SRF ( MHz ) nom. SQ0805R56ML□ -□□□ 0.56 ±20% SQ08051R2ML□ -□□□ 1). □：Packaging information… A：Bulk B：Taping Reel 2). "":Reference code 3). Inductance Test Freq. at 100KHz / 0.25V. 4). Irms Base on △T = 40℃ max. 5). Isat Base on △L/L0A = 30％ typ. □□□ @ Inductance vs. DC Currnt curve. Inductance（uH） 102 7 5 3 2 330 101 7 5 100 3 2 2R2 100 7 5 R56 3 2 10-1 101 2 3 5 7 102 2 3 5 7 103 DC Current (mA) AE-001A 2 3 5 7 104 SPECIFICATION FOR APPROVAL REF : PAGE: 3 PROD. ABC'S DWG NO. SMD POWER INDUCTOR NAME SQ0805□□□□L□-□□□ ABC'S ITEM NO. Ⅵ﹒PACKAGING INFORMATION： ( 1 ) Configuration T Cover tape N A B 2.0±0.5 ∮C ∮C D G Embossed carrier ※ Carrier tape width : D P:12 m/m 4 m/m End Start 100 100 Leader no component 200 m/m min. 100 100 100 Trailer No component 400 m/m Min. Components User direction of feed ( 2 ) Dimensions Unit:m/m Style A 13 - 16 330 B 21±0.8 C 13±0.5 D G N T 16 18 +0 50 -0 22.4 ( 3 ) Q'TY & G.W. Per package Series SQ0805 AE-001A Outer : Carton Inner : Reel Q'TY (pcs) G.W. (gw) 1,000 1,000 Style 13 - 16 Q'TY (pcs) 6,000 G.W. (Kg) 7.5 Size (cm) 40 x 40 x 24 SPECIFICATION FOR APPROVAL REF : PAGE: 4 PROD. SMD POWER INDUCTOR NAME ABC'S DWG NO. SQ0805□□□□L□-□□□ ABC'S ITEM NO. Ⅶ﹒DWGING NUMBER EXPRESSION： S Q 0 8 0 5 Reference code Appendix code 2 : Package Appendix code 1 : Classification Tolerance code Electrical code Dimension code Type code Appendix code 1：Product Classification L：Lead Free Standard products comply with RoHS' requirements 1 ~ 9：Lead Free Special products comply with RoHS' requirements Appendix code 2：Package Information Code AE-001A Inner package A T.B.D. B T / R ( Reel package ) Inner package Q'TY T.B.D. 1,000 pcs Remark SPECIFICATION FOR APPROVAL PAGE: 5 REF : PROD. NAME SMD POWER INDUCTOR ABC'S DWG NO. SQ0805□□□□L□-□□□ ABC'S ITEM NO. Ⅷ﹒RELIABILITY TEST： Test item Solderability Thermal shock test ( Temp. cycle ) Specification Test condition More than 90% of the terminal electrode Shall be covered With fresh solder. Preheat : 150±25℃ for 60 seconds Solder : Sn96.5 / Ag3 / Cu0.5 or equivalent Solder temp. : 235±5℃ Flux : Rosin Dip time : 4±1 seconds Inductance shall not change more than ±10% Room temp. 15 minutes -25±2 ℃ 30 minutes Room temp. 15 minutes 85±2 ℃ Total : 50 cycles Humidity Resistance test Temperature : 40±2℃ Humidity : 90 ~ 95% Applied current : Per spec. Time : 500 hours High temp. Resistance test Temperature : 105±2℃ Applied current : Per spec. Time : 500 hours AE-001A 30 minutes SPECIFICATION FOR APPROVAL PAGE: 6 REF : PROD. NAME ABC'S DWG NO. SMD POWER INDUCTOR SQ0805□□□□L□-□□□ ABC'S ITEM NO. Ⅸ﹒UL CARD： OBMW2 Magnet Wire-Component September 8, 2000 JUNG SHING WIRE CO LTD 231 CHUNG CHENG RD, SEC 3 JEN-TEH HSIANG, TAINAN HSIEN TAIWAN Mtl Dsg AIW CFUEWB EIAIW EILOCKY EILOCKW EIW EIW-2 FL.EILOCKY LSFFW LSUEW PEW PEY SF.FLW SF.EIW SF.BY@ SF.FLY@ SF.BLOCKBS SF.EILOCKY# SF.EILOCKBS SF.BW@ SFFW Mark Dsg ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ BC Coat Typ OC ____ ____ Polyamideimide Polyamide Modified Epoxy ____ ____ Polyamide ____ ____ ____ ____Nylon ____ Nylon Nylon Modified Polyamide Polyamide Modified Polyamide ____ Polyamideimide Polyurethane Polyesterimide Polyesterimide Polyesterimide Polyesterimide Polyesterimide Modified Polyester Polyurethane Polyurethane Polyester Polyester Modified Polyester Polyesterimide Modified Polyester Modified Polyester Modified Polyester Polyesterimide Polyesterimide Modified Polyester Polyurethane 287806002 Mtl Dsg SFFY UEW-1 UEW-2 UEW-4 UEY UEY-2 E174837 ANSI Type MW81-C MW75C MW35C ___ ___ ___ MW74-C ___ MW79-C ___ ___ MW24-C MW26C MW77C MW27-C MW27-C ___ ___ ___ ____ ____ ____ ____ ____ BC Coat Typ Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane 220 130 200 180 200 220 200 155 155 130 155 155 155 180 155 155 155 180 180 MW26C MW79 155 155 A not-for-profit organization dedicated to public safety and committed to quality service Page 1 of 2 Mark Dsg ____ Temp Class OC Polyamide ____ ____ ____ Nylon Polyamide ANSI Type MW80C MW2-C ___ MW75C MW28-C MW28-C Temp Class 155 105 130 130 130 130 @-May be suffixed by LZ; # - May be suffixed by LZ, EL or LZI. LZ - Signifies magned wires twisted together; EL - signifies base coated magnet wire laid parallel with top coat applied overall; LZL - signifies base coated magnet wire twisted together and covered with top coat overall. Marking: Company name or trademarks Recognized Component Mark. or 榮星電線 , material designation or marked designation on packaed or reel, and See General Information Preceding These Recognitions For use only in equipment where the acceptability of the combination is determined by Underwriters Laboratories Inc. 287806002 AE-001A Page 2 of 2 OBMW2⁄E174837 September 8 , 2000