LM5007EP LM5007EP Enhanced Plastic High Voltage (80V) Step Down Switching Regulator Literature Number: SNVS274D LM5007EP Enhanced Plastic High Voltage (80V) Step Down Switching Regulator General Description Features The LM5007EP Step Down Switching Regulator features all of the functions needed to implement low cost, efficient, Buck bias regulators. This high voltage regulator contains an 80 V, 0.7A N-Channel Buck Switch. The device is easy to apply and is provided in the MSOP-8 and the thermally enhanced LLP-8 packages. The regulator is based on a hysteretic control scheme using an on time inversely proportional to VIN. This feature allows the operating frequency to remain relatively constant with load and input voltage variations. The hysteretic control requires no control loop compensation, while providing very fast load transient response. An intelligent current limit is implemented in the LM5007EP with forced off time that is inversely proportional to VOUT. This current limiting scheme reduces load current foldback. Additional protection features include: Thermal Shutdown, Vcc undervoltage lockout, gate drive undervoltage lockout, and Max Duty Cycle limiter. ENHANCED PLASTIC • Extended Temperature Performance of −40°C to + 125°C • Baseline Control - Single Fab & Assembly Site • Process Change Notification (PCN) • Qualification & Reliability Data • Solder (PbSn) Lead Finish is standard • Enhanced Diminishing Manufacturing Sources (DMS) Support ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Integrated 80V, 0.7A N-Channel Buck Switch Internal HV Vcc Regulator No Control Loop Compensation Required Ultra-Fast Transient Response On Time Varies Inversely with Line Voltage Operating Frequency Nearly Constant with Varying Line Voltage Adjustable Output Voltage Highly Efficient Operation Precision Reference Low Bias Current Intelligent Current Limit Protection Thermal Shutdown External Shutdown Control Typical Applications ■ ■ ■ ■ Non-Isolated Buck Regulator Secondary High Voltage Post Regulator Selected Military Applications Selected Avionics Applications Ordering Information Part Number VID Part Number NS Package Number (Note 3) LM5007MMEP V62/04633-01 MUA08A (Note 1, Note 2) TBD TBD Note 1: For the following (Enhanced Plastic) versions, check for availability: LM5007MMXEP, LM5007SDEP, LM5007SDXEP Note 2: FOR ADDITIONAL ORDERING AND PRODUCT INFORMATION, PLEASE VISIT THE ENHANCED PLASTIC WEB SITE AT: www.national.com/ mil Note 3: Refer to package details under Physical Dimensions © 2011 National Semiconductor Corporation 200939 200939 Version 5 Revision 9 www.national.com Print Date/Time: 2011/09/23 14:00:21 LM5007EP Enhanced Plastic High Voltage (80V) Step Down Switching Regulator OBSOLETE September 23, 2011 LM5007EP Enhanced Plastic Connection Diagram 20093902 8-Lead MSOP, LLP Typical Application Circuit and Block Diagram 20093901 www.national.com 2 200939 Version 5 Revision 9 Print Date/Time: 2011/09/23 14:00:21 Pin Name 1 SW Switching Node Description Power switching node. Connect to the LC output filter. Application Information 2 BST Boost Boot–strap capacitor input An external capacitor is required between the BST and the SW pins. A 0.01uF ceramic capacitor is recommended. An internal diode between Vcc and BST completes the Buck gate drive bias network. 3 RCL Current Limit OFF time programming pin Toff = 10-5 / (0.59 + (FB / 7.22 x 10− 6 x RCL)) A resistor between this pin and RTN determines the variation of off time, along with the FB pin voltage, per cycle while in current limit. The off time is preset to 17uS if FB =0V and decreases as the FB pin voltage increases. 4 RTN Circuit Ground 5 FB Feedback Signal from Regulated Output This pin is connected to the inverting input of the internal regulation comparator. The regulation threshold is 2.5V. 6 RON On time set pin Ton = 1.42 x 10-10 RON / Vin A resistor between this pin and Vin sets the switch on time as a function of Vin. The minimum recommended on time is 300ns at the maximum input voltage. 7 Vcc Output from the internal high voltage bias regulator. If an auxiliary voltage is available to raise the voltage VCC is nominally regulated to 7 Volts. on this pin, above the regulation setpoint (7V), the internal series pass regulator will shutdown, reducing the IC power dissipation. Do not exceed 14V. This output provides gate drive power for the internal Buck switch. An internal diode is provided between this pin and the BST pin. A local 0.1uF decoupling capacitor is recommended. Series pass regulator is current limited to 10mA. 8 Vin Input supply voltage Recommended operating range: 9V to 75V 3 200939 Version 5 Revision 9 Print Date/Time: 2011/09/23 14:00:21 www.national.com LM5007EP Enhanced Plastic Pin Descriptions LM5007EP Enhanced Plastic BST to VCC BST to SW VCC to GND All Other Inputs to GND Lead Temperature (Soldering 4 sec) Storage Temperature Range Absolute Maximum Ratings (Note 4) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. VIN to GND BST to GND SW to GND (Steady State) ESD Rating (Note 8) Human Body Model Machine Model 80V 94V -1V Operating Ratings 80V 14V 14V -0.3 to 7V 260°C -55°C to +150°C (Note 4) VIN Junction Temperature 2kV 200V 9V to 75V −40°C to + 125°C Electrical Characteristics Specifications with standard typeface are for TJ = 25°C, and those with boldface type apply over full Operating Junction Temperature range. VIN = 48V, unless otherwise stated (Note 6). Symbol Parameter Conditions Min Typ Max Units 6.6 7 7.4 V Startup Regulator VCC Reg VCC Regulator Output VCC Current Limit (Note 7) 11 mA VCC undervoltage Lockout Voltage (VCC increasing) 6.3 V VCC Undervoltage Hysteresis 206 mV VCC Supply VCC UVLO Delay (filter) 3 µs Operating Current (ICC) Non-Switching, FB = 3V 500 675 µA Shutdown/Standby Current RON = 0V 100 200 µA ITEST = 200mA, VBST −VSW = 6.3V (Note 9) 0.74 1.34 Ω 4.5 5.5 Switch Characteristics Buck Switch Rds(on) Gate Drive UVLO (VBST – VSW) Rising 3.4 Gate Drive UVLO Hysteresis 400 V mV Breakdown Voltage VIN to Ground TJ = 25°C TJ = -40°C to +125°C 80 76 V Breakdown Voltage BST to VCC TJ = 25°C TJ = -40°C to +125°C 80 76 V Current Limit Current Limit Threshold 535 725 900 mA Current Limit Response Time Iswitch Overdrive = 0.1A Time to Switch Off 225 ns OFF time generator (test 1) FB=0V, RCL = 100K 17 µs OFF time generator (test 2) FB=2.3V, RCL = 100K 2.65 µs On Time Generator TON -1 Vin = 10V RON = 200K 2.15 2.77 3.5 µs TON -2 Vin = 75V RON = 200K 290 390 490 ns Remote Shutdown Threshold Rising 0.45 0.7 1.1 Remote Shutdown Hysteresis www.national.com 40 4 200939 Version 5 Revision 9 Print Date/Time: 2011/09/23 14:00:21 V mV Parameter Conditions Min Typ Max Units Minimum Off Time Minimum Off Timer FB = 0V 300 ns Regulation and OV Comparators FB Reference Threshold Internal reference Trip point for switch ON FB Over-Voltage Threshold Trip point for switch OFF 2.445 2.5 V 2.550 2.875 V 100 nA Thermal Shutdown Temp. 165 °C Thermal Shutdown Hysteresis 25 °C MUA Package 200 °C/W SDC Package 40 °C/W FB Bias Current Thermal Shutdown Tsd Thermal Resistance θJA Junction to Ambient Note 4: Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which operation of the device is intended to be functional. For guaranteed specifications and test conditions, see the Electrical Characteristics. Note 5: For detailed information on soldering plastic MSOP and LLP packages, refer to the Packaging Data Book available from National Semiconductor Corporation. Note 6: All limits are guaranteed. All electrical characteristics having room temperature limits are tested during production with TA = TJ = 25°C. All hot and cold limits are guaranteed by correlating the electrical characteristics to process and temperature variations and applying statistical process control. Note 7: The VCC output is intended as a self bias for the internal gate drive power and control circuits. Device thermal limitations limit external loading. Note 8: The human body model is a 100pF capacitor discharge through a 1.5kΩ resistor into each pin. The machine model is a 200pF capacitor discharged directly into each pin. The machine model ESD compliance level for Pin 5 is 150V. The human body ESD compliance level for Pin 7 and 8 is 1000V. Note 9: For devices procurred in the LLP-8 package the Rds(on) limits are guaranteed by design characterization data only. the 300ns off time, the switch will turn on again for another on time period. This switching behavior will continue until the FB pin voltage reaches the reference voltage level. The LM5007EP operates in discontinuous conduction mode at light load currents or continuous conduction mode at heavier load currents. In discontinuous conduction mode, current through the output inductor starts at zero and ramps up to a peak value during the buck switch on time and then back to zero during the off time. The inductor current remains at zero until the next on time period starts when FB falls below the internal reference. In discontinuous mode the operating frequency can be relatively low and will vary with load. Therefore at light loads the conversion efficiency is maintained, since the switching losses decrease with the reduction in load current and switching frequency. The approximate discontinuous mode operating frequency can be calculated as follows: Detailed Operating Description The LM5007EP Step Down Switching Regulator features all of the functions needed to implement low cost, efficient, Buck bias regulators. This high voltage regulator contains an 80V, 0.7A N-Channel Buck Switch. The device is easy to apply and is provided in the MSOP-8 and the thermally enhanced LLP-8 packages. The regulator is based on a hysteretic control scheme using an on time inversely proportional to Vin. This feature allows the operating frequency to remain relatively constant with load and input voltage variations. The hysteretic control requires no control loop compensation, while providing very fast load transient response. An intelligent current limit scheme is implemented in the LM5007EP with forced off time, after current limit detection, which is inversely proportional to Vout. This current limiting scheme reduces load current foldback. Additional protection features include: Thermal Shutdown, Vcc undervoltage lockout, Gate drive undervoltage lockout and Max Duty Cycle limiter. The LM5007EP can be applied in numerous applications to efficiently regulate step down higher voltage inputs. This regulator is well suited for 48 Volt Telcom and the new 42V Automotive power bus ranges. In continuous conduction mode, current flows continuously through the inductor and never ramps down to zero. In this mode the operating frequency is greater than the discontinuous mode frequency and remains relatively constant with load and line variations. The approximate continuous mode operating frequency can be calculated as follows: Hysteretic Control Circuit Overview The LM5007EP is a Buck DC-DC regulator that uses an on time control scheme. The on time is programmed by an external resistor and varies inversely with line input voltage (Vin). The core regulation elements of the LM5007EP are the feedback comparator and the on time one-shot. The regulator output voltage is sensed at the feedback pin (FB) and is compared to an internal reference voltage (2.5V). If the FB signal is below the reference voltage, the buck switch is turned on for a fixed time pulse determined by the line voltage and a programming resistor (RON). Following the on period the switch will remain off for at least the minimum off timer period of 300ns. If the FB pin voltage is still below the reference after The output voltage (Vout) can be programmed by two external resistors as shown in Figure 1. The regulation point can be calculated as follows: VOUT = 2.5 x (R1 + R2) / R2 5 200939 Version 5 Revision 9 Print Date/Time: 2011/09/23 14:00:21 www.national.com LM5007EP Enhanced Plastic Symbol LM5007EP Enhanced Plastic The feedback comparator in hysteretic regulators depend upon the output ripple voltage to switch the output transistor on and off at regular intervals. In order for the internal comparator to respond quickly to changes in output voltage, proportional to inductor current, a minimum amount of capacitor Equivalent Series Resistance (ESR) is required. A ripple voltage of 25mV to 50mV is recommended at the feedback pin (FB) for stable operation. In cases where the intrinsic capacitor ESR is too small, additional series resistance may be added. For applications where lower output voltage ripple is required the load can be connected directly to the low ESR output capacitor, as shown in Figure 1. The series resistor (R) will degrade the load regulation. Another technique for enhancing the ripple voltage at the FB pin is to place a capacitor in parallel with the feedback divider resistor R1. The addition of the capacitor reduces the attenuation of the ripple voltage from the feedback divider High Voltage Bias Regulator The LM5007EP contains an internal high voltage bias regulator. The input pin (Vin) can be connected directly to line voltages from 9 to 75 Volts. The regulator is internally current limited to 10mA. Upon power up, the regulator is enabled and sources current into an external capacitor connected to the Vcc pin. When the voltage on the Vcc pin reaches the regulation point of 7V, the controller output is enabled. An external auxiliary supply voltage can be applied to the Vcc pin. If the auxiliary voltage is greater than 7 Volts the internal regulator will essentially shutoff, thus reducing internal power dissipation. 20093905 FIGURE 1. Low Ripple Output Configuration www.national.com 6 200939 Version 5 Revision 9 Print Date/Time: 2011/09/23 14:00:21 LM5007EP Enhanced Plastic 20093906 FIGURE 2. Self Biased Configuration resistor and into the RON terminal is approximately proportional to Vin and used internally to control the on timer. This scheme of input voltage feed-forward hysteretic operation achieves nearly constant operational frequency over varying line and load conditions. The on time equation for the LM5007EP is : Over-Voltage Comparator The over-voltage comparator is provided to protect the output from overvoltage conditions due to sudden input line voltage changes or output loading changes. The over-voltage comparator monitors the FB pin versus an internal 2.875V reference (OV_REF). If the voltage at FB rises above OV_REF the comparator immediately terminates the buck switch on time pulse. Ton = 1.42 x 10-10 x RON / VIN The RON pin of the LM5007EP also provides a shutdown function which disables the regulator and significantly decreases quiescent power dissipation. By pulling the RON pin to below 0.7V logic threshold activates the low power shutdown mode. The VIN quiescent current in the shutdown mode is approximately 100µA internal to the LM5007EP plus the current in the RON resistor. On Time Generator and Shutdown The on time of the LM5007EP is set inversely proportional to the input voltage by an external resistor connected between RON and Vin. The RON terminal is a low impedance input biased at approximately 1.5V. Thus the current through the 7 200939 Version 5 Revision 9 Print Date/Time: 2011/09/23 14:00:21 www.national.com LM5007EP Enhanced Plastic 20093907 FIGURE 3. Shutdown Implementation circuit works in conjunction with an external bootstrap capacitor and an internal high voltage diode. The bootstrap capacitor is charged by VCC through the internal high voltage diode. A 0.01uF ceramic capacitor connected between the BST pin and SW pin is recommended. During each cycle when the Buck switch turns off, the SW pin is approximately 0V. When the SW pin voltage is low, the bootstrap capacitor will be charged from Vcc through the internal diode. The minimum off timer, set to 300ns, ensures that there will be a minimum interval every cycle to recharge the bootstrap capacitor. An external re-circulating diode from the SW pin to ground is necessary to carry the inductor current after the internal Buck switch turns off. This external diode must be of the Ultra-fast or Schottky type to reduce turn-on losses and current overshoot. The reverse voltage rating of the re-circulating diode must be greater than the maximum line input voltage. Current Limit The LM5007EP contains an intelligent current limit off timer intended to reduce the foldback characteristic inherent with fixed off-time over-current protection. If the current in the Buck switch exceeds 725mA the present cycle on time is immediately terminated (cycle by cycle current limit). Following the termination of the cycle a non-resetable current limit off timer is initiated. The duration of the off time is a function of the external resistor (RCI) and the FB pin voltage. When the FB pin voltage equals zero, the current limit off time is internally preset to 17uS. This condition occurs in short circuit operation when a maximum amount of off time is required. In cases of overload (not complete short circuit) the current limit off time can be reduced as a function of the output voltage (measured at the FB pin). Reducing the off time with smaller overloads reduces the amount of foldback and also reduces the initial start-up time. The current limit off time for a given FB pin voltage and RCI resistor can be calculated by the following equation: Thermal Protection Internal Thermal Shutdown circuitry is provided to protect the integrated circuit in the event the maximum junction temperature is exceeded. When thermal protection is activated, typically at 165 degrees Celsius, the controller is forced into a low power reset state, disabling the output driver. This feature is provided to prevent catastrophic failures from accidental device overheating. Toff = 10-5 / (0.59 + (VFB / 7.22 x 10-6 x RCL)) Applications utilizing low resistance inductors and/or a low voltage drop rectifier may require special evaluation at high line, short circuit conditions. In this special case the preset 17uS (FB = 0V) off time may be insufficient to balance the inductor volt*time product. Additional inductor resistance, output resistance or a larger voltage drop rectifier may be necessary to balance the inductor cycle volt*time product and limit the short circuit current. N - Channel Buck Switch and Driver The LM5007EP integrates an N-Channel Buck switch and associated floating high voltage gate driver. This gate driver www.national.com 8 200939 Version 5 Revision 9 Print Date/Time: 2011/09/23 14:00:21 LM5007EP Enhanced Plastic Typical Performance Characteristics LM5007EP 10V Output Efficiency Operational Waveforms 20093908 LM5007EP Operation: VOUT = 10V, VIN = 20V, IOUT = 250mA CH1: Switch Node, CH2: VOUT (AC), CH4: Inductor Current FIGURE 4. 20093910 FIGURE 6. Operational Waveforms Current Limit VFB vs TOFF RCL = 50k -600k 20093909 LM5007EP Operation: VOUT = 10V, VIN = 75V, IOUT = 250mA CH1: Switch Node, CH2: VOUT (AC), CH4: Inductor Current FIGURE 5. 20093911 FIGURE 7. 9 200939 Version 5 Revision 9 Print Date/Time: 2011/09/23 14:00:21 www.national.com LM5007EP Enhanced Plastic VIN vs TON RON = 100k, 200k, 300k 20093912 FIGURE 8. 10V, 400mA Demo Board Bill of Materials Item Part Number Description Value C1 C4532X7R2A105M CAPACITOR, CER, TDK 1µ, 100V C2 C4532X7R1E156M CAPACITOR, CER, TDK 15µ, 25V C3 C1206C104K5RAC CAPACITOR, CER, KEMET 0.1µ, 50V C4 C1206C103K5RAC CAPACITOR, CER, KEMET 0.01µ, 50V C5 OPEN UNUSED D1 MURA110T3 DIODE, 100V, ON SEMI L1 SLF7045T-101MR60-1 BUCK INDUCTOR, TDK 100µH R1 CRCW12062003F RESISTOR 200K R2 CRCW12061003F RESISTOR 100K R3 CRCW12063011F RESISTOR 3.01K R4 CRCW12061001F RESISTOR 1K R5 CRCW12061R00F RESISTOR 1 U1 LM5007 REGULATOR, NATIONAL www.national.com 10 200939 Version 5 Revision 9 Print Date/Time: 2011/09/23 14:00:21 LM5007EP Enhanced Plastic Physical Dimensions inches (millimeters) unless otherwise noted 8-Lead MSOP Package NS Package Number MUA08A 8-Lead LLP Package (4mm x 4mm) NS Package Number SDC08A 11 200939 Version 5 Revision 9 Print Date/Time: 2011/09/23 14:00:21 www.national.com LM5007EP Enhanced Plastic High Voltage (80V) Step Down Switching Regulator For more National Semiconductor product information and proven design tools, visit the following Web sites at: www.national.com Products Design Support Amplifiers www.national.com/amplifiers WEBENCH® Tools www.national.com/webench Audio www.national.com/audio App Notes www.national.com/appnotes Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns Data Converters www.national.com/adc Samples www.national.com/samples Interface www.national.com/interface Eval Boards www.national.com/evalboards LVDS www.national.com/lvds Packaging www.national.com/packaging Power Management www.national.com/power Green Compliance www.national.com/quality/green Switching Regulators www.national.com/switchers Distributors www.national.com/contacts LDOs www.national.com/ldo Quality and Reliability www.national.com/quality LED Lighting www.national.com/led Feedback/Support www.national.com/feedback Voltage References www.national.com/vref Design Made Easy www.national.com/easy www.national.com/powerwise Applications & Markets www.national.com/solutions Mil/Aero www.national.com/milaero PowerWise® Solutions Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors SolarMagic™ www.national.com/solarmagic PLL/VCO www.national.com/wireless www.national.com/training PowerWise® Design University THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION (“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright© 2011 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: [email protected] www.national.com Tel: 1-800-272-9959 National Semiconductor Europe Technical Support Center Email: [email protected] 200939 Version 5 Revision 9 National Semiconductor Asia Pacific Technical Support Center Email: [email protected] Print Date/Time: 2011/09/23 14:00:21 National Semiconductor Japan Technical Support Center Email: [email protected] IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP® Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2011, Texas Instruments Incorporated