TACT SwitchTM 6.2×7.15mm SidepushTM (Snap-in Type) SKRD Series 2pins with simple snap-in package. Detector Push Slide Rotary Encoders Power Dual-in-line Package Type TACT Switch TM CustomProducts Product Line Product No. Operating Operating Travel Rating Rating Operating life Initial contact force direction （mm）（max.） （min.） （5mA 5V DC） resistance SKRDLAA010 0.98N Horizontal SKRDLBA010 0.25 1.57N 50mA 12V DC 10BA 1V DC Stem color Minimum order unit（pcs.） Black 100,000cycles 1,000 100mΩ max. Dark gray Dimensions Unit:mm PC board mounting hole dimensions （Viewed from switch mounting face） Style Sharp Feeling Soft Feeling Snap-in Type 0.3 ø3.5 Surface Mount Type 6.2 4.5 0.7 1 3.2 4 0.9 7.1 s le ho 2 1 0.3 4.5 ø1 2- Radial Type stem 3.85 Circuit Diagram 6.2 3.3 Notes 1. Please use 1.6mm thick PC boards. 2. Please use single-sided PC boards. 1 2 Refer to P.306 for soldering conditions. 260 TACT SwitchTM List of Varieties Sharp Feeling Type SKHR Series SKHL SKHH SKHW SKRD SKQJ SKHL SKHH SKQJ SKHJ SKQB Detector Photo Push Type Snap–in Features Dust–proof Horizontal type type ― Operating direction ― Horizontal type With LED Water– proof ― ● ― ● ● ● ― Slide Rotary Vertical ● ● ● ● Encoders Horizontal ― ● ● ● ― Power W 6 6.2 □6 □4.5 Dimensions （mm） D 7.3 7.5 7.22 7.85 □6.6 3.5 7.15 □8 □10 8.5 5 Dual-in-line Package Type TACT SwitchTM H 3.8 4.3 7.4 5 4.3 7.4 7.3 CustomProducts 1N Operation force coverage 5N Ground terminal ― ● ― ● ● ― ｰ20℃ to ＋70℃ SKHJ/HL （Vertical Type）/QJ Operating temperature range Sharp Feeling ｰ30℃ to ＋85℃ Electrical performance Durability 100MΩ min. 100V DC Voltage proof 250V AC for 1min. Vibration 10 to 55 to 10Hz/min., the amplitude is 1.5mm for all the frequencies, in the 3 direction of X, Y and Z for 2hours respectively Lifetime Shall be in accordance with individual specifications. Environmental performance Soft Feeling Insulation resistance Cold ｰ30±2℃ for 96h Dry heat 80±2℃ for 96h Damp heat 60±2℃, 90 to 95%RH for 96h Page 252 253 255 259 260 261 253 Snap-in Type 255 261 Surface Mount Type Radial Type 263 265 W：Width. The most outer dimension excluding terminal portion. D ：Depth. The most outer dimension excluding terminal portion. H ：Height. The minimum dimension if there are variances. ● TACT SwitchTM Soldering Conditions ………………………………………………………………………………………306 ● TACT SwitchTM Cautions ………………………………………………………………………………………………………307 ● Product Line of Knob for TACT SwitchTM ……………………………………………………………………………………308 Note The automotive operating temperature range to be individually discussed upon request. 247 TACT SwitchTM Soldering Conditions Condition for Reflow Available for Surface Mount Type. 1. Heating method: Double heating method with infrared heater. 2. Temperature measurement: Thermocouple 0.1 to 0.2φ CA（K）or CC（T）at solder joints（copper foil surface）. A heat resistive tape Detector Push should be used to fix thermocouple. 3. Temperature profile Temperature (˚C ) Slide 260˚C max. 3 sec max. Rotary 230˚C 180 Encoders 150 Power Time Dual-in-line Package Type 120 sec max.（ pre-heating ） 40s max. TACT SwitchTM 3 to 4min. CustomProducts Time inside soldering equipment Note 1. The above temperature shall be measured on the mounting surface of a PC board. There are cases where the PC board's temperature greatly differs from that of the switch, depending on the material, size, thickness of PC boards and others. The above-stated conditions shall also apply to switch surface temperatures. 2. Soldering conditions differ depending on reflow soldering machines. Prior verification of soldering condition is highly recommended. Sharp Feeling Soft Feeling Conditions for Auto-dip （Except SKHJ, SKHL, SKQJ, SKQK, SKEG series） Snap-in Type Surface Mount Type Manual Soldering（Except SKRT Series） Available for Snap-in Type and Radial Type Items Condition Items Condition Soldering temperature 350℃max. Duration of soldering Flux built-up Radial Type Preheating temperature Preheating time Soldering temperature Mounting surface should not be exposed to fluk Capacity of soldering iron Ambient temperature of the soldered surface of PC board. 100℃ max. 60s max. 260℃ max. Duration of immersion 5s max. Number of soldering 2times max. Notes 1. 2. 3. 4. 5. 306 Consult with us for availability of TACT SwitchTM washing. Prevent flux penetration from the top side of the TACT SwitchTM. Switch terminals and a PC board should not be coated with flux prior to soldering. The second soldering should be done after the switch is stable with normal temperature. Use the flux with a specific gravity of min 0.81. （EC-19S-8 by TAMURA Corporation, or equivalents.） 3s max. 60W max.