plerowTM ALN0743 Internally Matched LNA Module Features Description · S21 = 37.6 dB @ 698 MHz = 36.4 dB @ 787 MHz · NF of 0.7 dB over Frequency · Unconditionally Stable · Single 5V Supply · High OIP3 @ Low Current The plerowTM ALN-series is the compactly designed surface-mount module for the use of the LNA with or without the following gain blocks in the infrastructure equipment of the mobile wireless (CDMA, GSM, PCS, PHS, WCDMA, DMB, WLAN, WiBro, WiMAX), GPS, satellite communication terminals, CATV and so on. It has an exceptional performance of low noise figure, high gain, high OIP3, and low bias current. The stability factor is always kept more than unity over the application band in order to ensure its unconditionally stable implementation to the application system environment. The surface-mount module package including the completed matching circuit and other components necessary just in case allows very simple and convenient implementation onto the system board in mass production level. Specifications (in Production) Typ. @ T = 25°C, Vs = 5 V, Freq. = 742.5 MHz, Zo.sys = 50 ohm Parameter Unit Frequency Range Min MHz 698 Gain dB 36 Gain Flatness dB Noise Figure (NF) Output IP3 S11 / S22 (1) (2) dBm (3) Max 787 37 40 ± 0.4 ± 0.5 0.70 0.75 More Information Website: www.asb.co.kr E-mail: [email protected] 41 dB Output P1dB Switching Time Typ dB dBm 2-stage Single Type Specifications Tel: (82) 42-528-7223 Fax: (82) 42-528-7222 -18 / -9 20 21 ASB Inc., 4th Fl. Venture Town Bldg., 367-17 Goijeong-Dong, Seo-Gu, Daejon 302-716, Korea µsec Supply Current mA 130 Supply Voltage V 5 Impedance Ω 50 150 Max. RF Input Power dBm C.W 29 ~ 31 (before fail) Package Type & Size mm Surface Mount Type, 13Wx13Lx3.8H Operating temperature is -40°C to +85°C. 1) OIP3 is measured with two tones at an output power of 7 dBm / tone separated by 1 MHz. 2) S11/S22 (max) is the worst value within the frequency band. 3) Switching time means the time that takes for output power to get stabilized to its final level after switching DC voltage from 0 V to Vs. Outline Drawing (Unit: mm) plerow ALN0743 ASB Inc. (Top View) (Bottom View) Pin Number Function 3 RF In 8 RF Out 10 Vs Others Ground Note: 1. The number and size of ground via holes in a circuit board is critical for thermal RF grounding considerations. 2. We recommend that the ground via holes be placed on the bottom of all ground pins for better RF and thermal performance, as shown in the drawing at the left side. Solder Stencil Area (Side View) Ø0.4 plated thru holes to ground plane (Recommended Footprint) 1/3 www.asb.co.kr February 2009 plerowTM ALN0743 Internally Matched LNA Module S-parameters Typical Performance (Measured) 698~787 +5 V Noise Figure S-parameters & K Factor OIP3 2/3 P1dB www.asb.co.kr February 2009 plerowTM ALN0743 Internally Matched LNA Module Application Circuit VS + - Tantal or MLC (Multi Layer Ceramic) Capacitor C1 C2 ALN IN OUT 1) The tantal or MLC (Multi Layer Ceramic) capacitor is optional and for bypassing the AC noise introduced from the DC supply. The capacitance value may be determined by customer’s DC supply status. The capacitor should be placed as close as possible to Vs pin and be connected directly to the ground plane for the best electrical performance. 2) DC blocking capacitors are always necessarily placed at the input and output port for allowing only the RF signal to pass and blocking the DC component in the signal. The DC blocking capacitors are included inside the ALN module. Therefore, C1 & C2 capacitors may not be necessary, but can be added just in case that the customer wants. The value of C1 & C2 is determined by considering the application frequency. Evaluation Board Layout Recommended Soldering Reflow Process Vs 20~40 sec 260°C Ramp-up (3˚C/sec) 200°C Ramp-down (6°C/sec) OUT IN 150°C Size 25x25mm (for ALN Series – 13x13mm) 60~180 sec 3/3 www.asb.co.kr February 2009