HIGH FREQUENCY MAGNETICS T1/CEPT Dual Line Interface Transformers • Designed to meet the stringent demands of high density designs • Low height profile TM00130 • Minimum interwinding breakdown voltage of 1500 Vrms • Reference data sheet TM9906 for additional dual surface mount transformers ELECTRICAL SPECIFICATIONS at 25° C Turns Ratio ±5% Part Number Primary Inductance mH min Leakage Inductance µH max Interwinding Capacitance pF max DCR Primary Ω max Coil A Coil B Coil A & B Coil A / Coil B Coil A & B Coil A Coil B S553-0013-00 1 :1.385 CT 1:1:1 1.20 0.80 / 0.50 35 0.80 0.80 S553-0013-01 1 CT : 2 CT 1:1 1.20 0.80 / 0.50 35 0.80 0.80 S553-0013-02 1: 2CT 1 : 1.36 1.20 0.80 / 0.80 35 0.80 0.80 S553-0013-03 1 : 2 CT 1 : 2 CT 1.20 0.80 / 0.80 35 0.80 0.80 S553-0013-06 1 : 1.15 CT 1 : 2 CT 1.20 0.50 / 0.80 35 0.80 0.80 S553-0013-07 1 : 1 / 1 : 1.26 1 : 2 CT 1.20 0.80 / 0.80 35 0.80 0.80 S553-0013-22 1 : 1 / 1 : 1.26 1CT : 2 CT 1.20 0.60 / 0.60 30 0.70 0.70 SCHEMATICS S553-0013-00 Primary 1 S553-0013-02 S553-0013-01 Secondary 16 Primary 1 Secondary 16 15 2 15 2 14 12 3 14 3 14 6 11 6 11 8 9 8 9 Primary Secondary Secondary 1 Primary 16 Coil A 2 7 11 10 Coil B 8 Primary 9 Secondary Secondary Primary ©2002 Bel Fuse Inc. Specifications subject to change without notice. 05.02 Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com T1-67 HIGH FREQUENCY MAGNETICS T1/CEPT Dual Line Interface Transformers TM00130 SCHEMATICS S553-0013-03 S553-0013-06 S553-0013-07* S553-0013-22 Secondary 1 Coil A Primary 16 2 Primary 16 2 3 14 3 14 6 11 6 11 10 7 10 8 9 8 9 Primary Secondary Primary Secondary Coil B *S553-0013 -07 *S553-0013 -07 1:1 1 : 1.26 1:1 1 : 1.26 (14 - 16) : (1 - 2) (14 - 16) : (2 - 3) 0.500 [12.70] max MECHANICAL S553-0013-00 S553-0013-01 S553-0013-02 S553-0013-03 S553-0013-06 S553-0013-07 S553-0013-22 Secondary 1 Suggested PCB Pad Layout 0.375 0.285 [9.53] [7.24] max max 0.425 [10.80] 0.050 [1.27] 0.018 ±0.002 [0.46 ±0.05] (14 - 16) : (2 - 3) (14 - 16) : (1 - 3) 0.050 [1.27] 0.025 [0.64] 0.070 [1.78] 0.225 [5.72] max 0.015 [0.38] 0.350 ±0.010 [8.89 ±0.25] 0.008 - 0.012 [0.20 - 0.30] 0.035 [0.89] 4˚ nom Dimensions are in inches [millimeters]. Standard dimension tolerance is ±0.010 [0.25] unless otherwise noted. ©2002 Bel Fuse Inc. Specifications subject to change without notice. 05.02 CORPORATE FAR EAST EUROPE Bel Fuse Inc. 206 Van Vorst Street Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com Bel Fuse Ltd. 8F / 8 Luk Hop Street San Po Kong Kowloon, Hong Kong Tel 852-2328-5515 Fax 852-2352-3706 www.belfuse.com Bel Fuse Europe Ltd. Preston Technology Management Centre Marsh Lane, Suite G7, Preston Lancashire, PR1 8UD, U.K. Tel 44-1772-556601 Fax 44-1772-888366 www.belfuse.com T1-68