BVLED BVU

BRIGHT VIEW
ELECTRONICS CO.,LTD
ULTRA BRIGHTNESS LED LAMP
BVU-5E1TT4
PACKAGE CONFIGURATION
5.9
5.9
DESCRIPTION
5.0
Dice Material : AlInGaP Yellow
Light Color : Yellow Color
Lens Color : Water Transparent
Stand-Off P/N : BVU-5E1TT4 R
4.9
7.6
12.8 0.5
RADIATION PATTERN
0°
-30°
1.0
30°
1.0Max.
1.3
1.0
25.4Min.
25.4Min.
-60°
60°
CATHODE
CATHODE
0.5
1.0Min.
2.54
100 75 50 25 0 25 50 75 100
Relative Luminous Intensity ( Iv % )
50% Power Angle 15°
2.54
Tolerance ± 0.25 ㎜
ABSOLUTE MAXIMUM RATINGS AT Ta = 25 ℃
PARAMETER
MAX.
Power Dissipation (PD)
Continuous Forward Current (IF)
Peak Forward Current ( 1/10 Duty Cycle , 0.1ms Pulse Width ) (IFP)
Reverse Voltage (VR)
80
30
160
5
0.4
Derating Linear From 50 ℃
Operating Temperature Range (Topr)
-40 ℃ to + 100 ℃
Storage Temperature Range (Tstg)
-40 ℃ to + 100 ℃
Lead Solder Temperature 1.6 mm Below Package 260 ℃ for 5 seconds (Tsld)
UNIT
mW
mA
mA
V
mA/oC
ELECTRICAL / OPTICAL CHARACTERISTICS AT Ta = 25 ℃
SYMBOL
VF
IR
λp
λd
2θ1/2
IV
PARAMETER
TEST COND.
Forward Voltage
Reverse Current
Peak Emission Wavelength
Dominant Wavelength
Viewing Angle
Luminous Intensity
MIN.
I F = 20 mA
V R = 5V
I F = 20 mA
I F = 20 mA
I F = 20 mA
I F = 20 mA
MAX.
2.3
2.8
100
UNIT
V
μA
nm
nm
Deg
mcd
592
590
15
4125
2800
BIN GRADE LIMITS (IF=20 mA)
LUMINOUS INTENSITY / mcd
TYP.
BIN GRADE LIMITS (IF=20 mA)
DOMINANT WAVELENGTH / nm
Bin
N
O
P
Q
R
Min.
2800
3600
4650
6000
7800
Max.
3600
4650
6000
S
Bin
YC
YD
YE
YF
YG
10000 Min.
583
586
589
592
595
7800 10000 13000 Max.
586
589
592
595
598
Tolerance ± 15%mcd
*Bright View reserves the rights to alter specifications and remove availability of products at any time without notice.
*Dominant Wavelength, λd is according to CIE Chromaticity Diagram base on color of lamps.
*θ1/2 is the off-axis angle where the luminous intensity is one half the on-axis intensity.
2008/7/15 – B
BRIGHT VIEW
ELECTRONICS CO.,LTD
ULTRA BRIGHTNESS LED LAMP
BVU-5E1TT4
TYPICAL ELECTRICAL / OPTICAL CHARACTERISTIC CURVES
3.0
Relative Intensity
1.3
1.8
2.3
2.8
Forward Voltage Vf ( V )
2.0
1.5
1.0
0.5
0
3.3
FIG. 3 Relative Voltage vs. Temperature
0
Relative Intensity @ 20mA
1.0
0.9
0.8
-50
70
-25
0
25
50
75
2.5
2.0
1.5
1.0
0.5
0
-50 -25
100 125
Ambient Temperature Ta ( °C )
FIG. 5 Relative Intensity vs. Wavelength ( λp )
( Ta = 25 °C )
0.5
0
500
550
600
Wavelength ( nm )
0
25
50
75
100 125
Ambient Temperature Ta ( °C )
FIG. 6 Maximum Forward Current
IF-DC Forward Current ( mA )
Forward Intensity @ 20mA
20 30 40 50 60
Forward Current If ( mA )
3.0
1.1
1.0
10
FIG. 4 Relative Intensity vs. Temperature
1.2
Forward Voltage @ 20mA
FIG. 2 Relative Intensity vs. Forward Current
( Ta = 25 °C )
2.5
Forward Current ( mA )
100
90
80
70
60
50
40
30
20
10
0
FIG. 1 Forward Current vs. Forward Voltage
( Ta = 25 °C )
650
40
vs. Temperature
30
20
10
0
0
20
40
60
80 100
Ambient Temperature Ta ( °C )
120
2008/7/15 – B
BRIGHT VIEW
ELECTRONICS CO.,LTD
ULTRA BRIGHTNESS LED LAMP
BVU-5E1TT4
Apply to LAMP(DIP) series.
Description:
( 1 ) Manual soldering (Solder Iron)
(1.1) Temperature at tip of the iron: 300°C Max.
(1.2) It's banned to load any stress on the resin during soldering.
(1.3) Soldering time: 3 sec. Max.(one time only)
(1.4) Leave 3mm of minimum distance from the base of epoxy.
( 2 ) Dip Soldering(Wave soldering-Solder Bath)
(2.1) Leave 3mm of minimum distance from the base of the epoxy.
Soldering beyond the base of the tie bar(stand off) is recommended.
(2.2) When soldering, do not put stress on the LEDs during heating.
(2.3) Cutting the leadframes at high temperatures may cause LED failure.
(2.4) Never take next process until the component is cooled down to room temperature
after reflow.
(2.5) After soldering, do not warp the circuit board.
(2.6) The recommended dip soldering profile is the following:
Temperature ( C )
Degree C.
300.0
275.0
250.0
225.0
200.0
175.0
150.0
125.0
100.0
75.0
50.0
25.0
0.0
MAX 260 C , 5 sec.
>20 C
4 C / sec.
150 C
0.0
50.0
100.0
150.0
200.0
250.0
300.0
Time ( sec. )
2008/7/15 – B
BRIGHT VIEW
ELECTRONICS CO.,LTD
ULTRA BRIGHTNESS LED LAMP
BVU-5E1TT4
Label 2
Label 1
Bright View
Bright View
Electronics Co.,Ltd.
BVU-XXXXXXXX
PART NO.:
LOT NO.:
GRADE:
Q'ty
LOT NO.:
X-
pcs
GRADE:
QA
Pb - Free / RoHS Compliant
3mm or 5mm Polybag
Anti-electrostatic bag
Q'ty
pcs
QA
Pb - Free / RoHS Compliant
ELECTROSTATIC SENSITIVE DEVICES
DO NOT OPEN OR HANDLE EXCEPT
AT A STATIC-FREE WORKSTATION
X: Bin grade
: Wavelength
: Vf
BOX
Dimension(cm): 29*25*15
BVU - X X X X X X X R
25
29
Stand-offs
Luminous Grade-refer to the selection guide for BIN options
Lens Color-refer to lens color (1) to (9)
Dice Code-refer to the selection guide
Lens Configuration-refer to lens drawing
View Angle-refer to the selection guide (A) to (Z)
Outline Dimension-refer to the outline dimension
3
15
TYPE
Q'TY
N,W
G,W
C.NO
Electronics Co.,Ltd.
PART NO.:
PCS
KGS
KGS
Label 1 or Label 2 attach on it.
Device
Q'ty / Polybag (pcs)
Fig.
Polybag / Box A
5mm(T-1 3/4)
1000pcs
14 bags
Label 1
3mm(T-1)
1000pcs
20 bags
Label 1
500pcs
18 bags
Label 2
Blue / Green / White
32
53
RE
Y
CARTON
Dimension(cm): 53*32*33
33
ITEM NO.
DEVICE:
Q'TY
N. W.:
G. W.:
PCS.
KGS.
KGS.
4 Boxes / Carton
5mm : 56,000pcs
3mm : 80,000pcs
Blue / Green / White : 36,000pcs
2008/7/15 – B