BRIGHT VIEW ELECTRONICS CO.,LTD ULTRA BRIGHTNESS LED LAMP BVU-5K5TT4 PACKAGE CONFIGURATION 5.9 5.9 DESCRIPTION 5.0 4.9 Dice Material : AlInGaP Yellow Light Color : Yellow Color Lens Color : Water Transparent Stand-Off P/N : BVU-5K5TT4 R 7.6 1.0Max. RADIATION PATTERN 0° -30° 12.0±0.5 1.0 30° 1.3 1.0 25.4Min. -60° 60° 25.4Min. CATHODE CATHODE 0.5 2.54 100 75 50 25 0 2.54 1.0Min. 25 50 75 100 Tolerance ± 0.25 ㎜ Relative Luminous Intensity ( Iv % ) ABSOLUTE MAXIMUM RATINGS AT Ta = 25 ℃ PARAMETER MAX. Power Dissipation (PD) Continuous Forward Current (IF) Peak Forward Current ( 1/10 Duty Cycle , 10ms Pulse Width ) (IFP) Reverse Voltage (VR) 80 30 100 5 0.4 Derating Linear From 50 ℃ Operating Temperature Range (Topr) －30 ℃ to ＋ 85 ℃ Storage Temperature Range (Tstg) －40 ℃ to ＋ 100 ℃ Lead Solder Temperature 1.6 mm Below Package 260 ℃ for 5 seconds (Tsld) UNIT mW mA mA V mA/oC ELECTRICAL / OPTICAL CHARACTERISTICS AT Ta = 25 ℃ SYMBOL VF IR λp λd 2θ1/2 IV PARAMETER TEST COND. Forward Voltage Reverse Current Peak Emission Wavelength Dominant Wavelength Viewing Angle Luminous Intensity I F = 20 mA V R = 5V I F = 20 mA I F = 20 mA I F = 20 mA I F = 20 mA MIN. 6000 TYP. MAX. 2.3 2.8 100 592 590 25 7800 BIN GRADE LIMITS (IF=20 mA) LUMINOUS INTENSITY / mcd BIN GRADE LIMITS (IF=20 mA) DOMINANT WAVELENGTH / nm Bin Q R S Bin YD YE YF Min. 6000 7800 10000 Min. 586 589 592 Max. 7800 10000 13000 Max. 589 592 595 UNIT V μA nm nm Deg mcd Tolerance ± 15%mcd *Bright View reserves the rights to alter specifications and remove availability of products at any time without notice. *Dominant Wavelength, λd is according to CIE Chromaticity Diagram base on color of lamps. *θ1/2 is the off-axis angle where the luminous intensity is one half the on-axis intensity. 2009/6/23 - B BRIGHT VIEW ELECTRONICS CO.,LTD ULTRA BRIGHTNESS LED LAMP BVU-5K5TT4 TYPICAL ELECTRICAL / OPTICAL CHARACTERISTIC CURVES 100 80 60 40 20 0 1.3 FIG. 3 Forward Voltage vs. Temperature ( If = 20 mA ) 1.1 1.0 0.9 0.8 -50 -25 0 25 50 75 4.0 3.0 2.0 1.0 0 3.3 3.0 Relative Intensity ( a.u ) Forward Voltage ( a.u ) 1.2 1.8 2.3 2.8 Forward Voltage Vf ( V ) FIG. 2 Relative Intensity vs. Forward Current ( Ta = 25 °C ) 5.0 Relative Intensity Forward Current ( mA ) 120 FIG. 1 Forward Current vs. Forward Voltage ( Ta = 25 °C ) 0 2.0 1.5 1.0 0.5 25 50 75 100 125 FIG. 6 Maximum Forward Current IF-DC Forward Current ( mA ) Relative Emission Intensity ( a.u) 0.5 550 600 Wavelength ( nm ) 0 Ambient Temperature Ta ( °C ) FIG. 5 Relative Intensity vs. Wavelength ( λp ) ( Ta = 25 °C ) 0 500 120 2.5 0 -50 -25 100 125 40 80 100 60 Forward Current If ( mA ) FIG. 4 Relative Intensity vs. Temperature ( If = 20 mA ) Ambient Temperature Ta ( °C ) 1.0 20 650 40 vs. Temperature 30 20 10 0 0 20 40 60 80 100 Ambient Temperature Ta ( °C ) 120 2009/6/23 - B BRIGHT VIEW ELECTRONICS CO.,LTD ULTRA BRIGHTNESS LED LAMP BVU-5K5TT4 Apply to LAMP(DIP) series. Description: ( 1 ) Manual soldering (Solder Iron) (1.1) Temperature at tip of the iron: 300°C Max. (1.2) It's banned to load any stress on the resin during soldering. (1.3) Soldering time: 5 sec. Max.(one time only) (1.4) Leave 1.6mm of minimum distance from the base of epoxy. ( 2 ) Dip Soldering(Wave soldering-Solder Bath) (2.1) Leave 1.6mm of minimum distance from the base of the epoxy. Soldering beyond the base of the tie bar(stand off) is recommended. (2.2) When soldering, do not put stress on the LEDs during heating. (2.3) Cutting the leadframes at high temperatures may cause LED failure. (2.4) Never take next process until the component is cooled down to room temperature after reflow. (2.5) After soldering, do not warp the circuit board. (2.6) The recommended dip soldering profile is the following: Temperature ( C ) Degree C. 300.0 275.0 250.0 225.0 200.0 175.0 150.0 125.0 100.0 75.0 50.0 25.0 0.0 MAX 260 C ， 5 sec. >20 C 4 C / sec. 150 C 0.0 50.0 100.0 150.0 200.0 250.0 300.0 Time ( sec. ) 2009/6/23 - B BRIGHT VIEW ELECTRONICS CO.,LTD ULTRA BRIGHTNESS LED LAMP BVU-5K5TT4 Label 2 Label 1 Bright View Bright View Electronics Co.,Ltd. BVU-XXXXXXXX PART NO.: LOT NO.: GRADE: Q'ty LOT NO.: X- pcs GRADE: QA Pb - Free / RoHS Compliant 3mm or 5mm Polybag Anti-electrostatic bag Q'ty pcs QA Pb - Free / RoHS Compliant ELECTROSTATIC SENSITIVE DEVICES DO NOT OPEN OR HANDLE EXCEPT AT A STATIC-FREE WORKSTATION X: Bin grade : Wavelength : Vf BOX Dimension(cm): 29*25*15 BVU - X X X X X X X R 25 29 Stand-offs Luminous Grade-refer to the selection guide for BIN options Lens Color-refer to lens color (1) to (9) Dice Code-refer to the selection guide Lens Configuration-refer to lens drawing View Angle-refer to the selection guide (A) to (Z) Outline Dimension-refer to the outline dimension 3 15 TYPE Q'TY N,W G,W C.NO Electronics Co.,Ltd. PART NO.: PCS KGS KGS Label 1 or Label 2 attach on it. Device Q'ty / Polybag (pcs) Fig. Polybag / Box A 14 bags Label 1 5mm(T-1 3/4) 1000pcs 3mm(T-1) 1000pcs 20 bags Label 1 500pcs 18 bags Label 2 Blue / Green / White 32 53 RE Y CARTON Dimension(cm): 53*32*33 33 ITEM NO. DEVICE: Q'TY N. W.: G. W.: PCS. KGS. KGS. 4 Boxes / Carton 5mm : 56,000pcs 3mm : 80,000pcs Blue / Green / White : 36,000pcs 2009/6/23 - B