RGPP15 SERIES GLASS PASSIVATED FAST SWITCHING RECTIFIER CHENG- YI ELECTRONIC VOLTAGE RANGE 50 TO 1000 Volts CURRENT 1.5 Amperes DO-15 .034 (.86) .028 (.71) 1.0 MIN. (25.4) FEATURE High voltage High current capability Low leakage current High surge capability Low cost (7.6) .300 (5.8) .230 MECHANICAL DATA .140 (3.6) .104 (2.6) 1.0 MIN. (25.4) Case:Mold plastic use UL 94V-0 recognized flame retardant epoxy Terminals:Axial leads, solderable per MIL-STD-202, method 208 Polarity:Color band denotes cathode Mounting Position:Any Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 250C ambient temperature unless otherwise specified. Signle phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. RGPP15A RGPP15B RGPP15D RGPP15G RGPP15J RGPP15K RGPP15M Maximum Recurrent Peak Reverse Voltage 50 Maximum RMS Voltage 35 70 140 280 420 Maximum DC Blocking Voltage 50 100 200 400 600 100 200 Maximum Average Forward Rectified Current, .375", (9.5mm) Lead Length at TA =55 C 600 800 Peak Forward Surge Current 8.3 ms single half sine-wave V 560 700 V 800 1000 V A 50 Maximum Forward Voltage at 1.5A Peak A V 1.3 1.2 Maximum Reverse Current, Rated DC Full Cycle Average, .375", (9.5mm) Lead Length T A =55 C UNITS 1000 1.5 0 A 30 0 Maximum DC Reverse Current, at Rated DC Blocking Voltage Maximum Reverse Recovery Time (Note 1) 400 A 5.0 150 Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range Notes : 1. Reverse Recovery Test Conditions : IF=.5A, I R=1A, Irr=.25A 2. Measured at 1.0MHz and applied reverse voltage of 4.0 Volts 150 150 150 15 -65 to +175 250 500 500 nS pF 0 C RGPP15 SERIES GLASS PASSIVATED FAST SWITCHING RECTIFIER CHENG- YI ELECTRONIC RATING AND CHARACTERISTICS CURVES RGPP15 SERIES Fig. 1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM trr 10 NONINDUCTIVE 50 NONINDUCTIVE +0.5A ( ) D.U.T. (+) 0 PULSE GENERATOR (NOTE 2) 25 Vdc (approx.) ( ) 1 NONINDUCTIVE OSCILLOSCOPE (NOTE 1) -0.25 (+) -1.0A NOTES : 1. Rise Time=7ns max., Input Impedance= 1 megohm, 22pF. 2. Rise Time=10ns max., Source Impedance= 50 ohms. Fig. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS Fig. 2 - FORWARD CURRENT DERATING CURVE 1.25 1.00 .75 .25 SINGLE PHASE HALF WAVE 60HZ RESISTIVE OR INOUCTIVE LOAD .375" (9mm) LEAD LENGTH 0 25 50 75 100 10 INSTANTANEOUS FORWARD CURRENT, AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES 1.50 .50 125 150 SET TIME BASE FOR 50 / 100ns/cm 1cm 1.0 TJ = 250C 0.1 .01 175 .4 .6 .8 1.0 1.2 1.4 1.6 AMBIENT TEMPERATURE, 0C INSTANTANEOUS FORWARD VOLTAGE, VOLTS Fig. 4 - TYPICAL JUNCTION CAPACITANCE Fig. 5 - PEAK FORWARD SURGE CURRENT FORWARD SURGE CURRENT, AMPERES CAPACITANCE-pF 100 0 TJ=25C 10 60 50 0 TJ=25C 40 30 20 1 1 10 100 10 1 REVERSE VOLTAGE. VOLTS 10 NUMBER OF CYCLES AT 60Hz 100