UF2001PT CHENMKO ENTERPRISE CO.,LTD THRU HIGH EFFICIENCY RECTIFIER VOLTAGE RANGE 50 - 1000 Volts UF2007PT CURRENT 2.0 Amperes FEATURES * Plastic package has Underwriters Laboratory Flammability Classification 94V-0 * Low power loss, high efficiency * Low leakage * Low forward voltage drop * High current capability * High surge capability * High speed switching * High reliability DO-15 0.034(0.9) DIA. 0.028(0.7) 1.0(25.4) MIN. MECHANICAL DATA Case: JEDEC DO-15 molded plastic Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.38 gram 0.300(7.6) 0.230(5.8) 0.140(3.6) DIA. 0.104(2.6) 1.0(25.4) MIN. MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25oC ambient temperature unless otherwise specified. Single phase, half wave, 60 HZ, resistive or inductive load. For capacitive load, derate current by 20%. DO-15 Dimensions in inches and (millimeters) MAXIMUM RATINGES ( At TA = 25oC unless otherwise noted ) SYMBOL UF2001P UF2003PT UF2004PT UF2005PT UF2006PT UF2007PT UNITS Maximum Recurrent Peak Reverse Voltage RATINGS VRRM 50 100 200 400 600 800 1000 Volts Maximum RMS Voltage VRMS 35 70 140 280 420 560 700 Volts Maximum DC Blocking Voltage VDC 50 100 200 400 600 800 1000 Volts Maximum Average Forward Rectified Current 0.375" (9.5mm) Lead Length TA = 55oC Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Junction Capacitance (Note 1) T UF2002PT IO 2.0 Amps IFSM 60 Amps CJ 30 17 JL 12 o C/W R JA 40 o C/W Maximum Thermal Resistance (Note 2) Operating and Storage Temperature Range pF R TJ, TSTG o -55 to +150 C ELECTRICAL CHARACTERISTICS ( At TA = 25oC unless otherwise noted ) CHARACTERISTICS SYMBOL Maximum Instantaneous Forward Voltage at 2.0 A DC Maximum DC Reverse Current TA = 25oC at Rated DC Blocking Voltage TA = 125oC Maximum Reverse Recovery Time (Note 3) VF UF2001P T UF2002PT UF2003PT UF2004PT 1.0 UF2005PT UF2006PT 1.3 UF2007PT 1.7 10 UNITS Volts uAmps IR 50 trr 50 NOTES : 1. Measured at 1.0 MHZ and applied reverse voltage of 4.0 volts 2. Thermal Resistance from Junction to Ambient, and from junction to lead length 0.375" (9.5mm) P.C.B. mounted. 3. Test Conditions : IF = 0.5 A, IR = -1.0 A, IRR = -0.25 A uAmps 75 nSec 2001-6 RATING CHARACTERISTIC CURVES ( UF2001PT THRU UF2007PT ) (+) 25 Vdc (approx) (-) 10 NONINDUCTIVE trr +0.5A (-) D.U.T 0 PULSE GENERATOR (NOTE 2) 1 NONINDUCTIVE OSCILLOSCOPE (NOTE 1) -0.25A (+) -1.0A 1cm NOTES: 1. Rise Time = 7ns max. Input Impedance = 1 megohm. 22pF. 2. Rise Time = 10ns max. Source Impedlance= 50 ohms. SET TIME BASE FOR 10/20 nS/cm FIG. 3 - TYPICAL REVERSE CHARACTERISTICS 0 0 25 50 75 100 125 150 175 AMBIENT TEMPERATURE ( OC ) TJ= 25oC .1 0 20 40 60 80 100 120 T 5P 00 F2 ~U 04 PT PT 20 T 7P 200 UF T~ 6P 200 TJ= 25oC 0.1 Pulse Width = 300uS 1% Duty Cycle 0.01 140 UF 003 UF2 .1 UF 1.0 PT~ TJ= 100oC 1.0 001 TJ= 125oC 10 UF2 INSTANTANEOUS FORWARD CURRENT, ( A ) INSTANTANEOUS REVERSE CURRENT, (uA) Single Phase Half Wave 60Hz Resistive or Inductive Load 2.0 FIG. 4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 0 PERCENT OF RATED PEAK REVERSE VOLTAGE, ( % ) FIG. 5 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT .2 .4 .6 .8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE, ( V ) FIG. 6 - TYPICAL JUNCTION CAPACITANCE 70 200 60 JUNCTION CAPACITANCE, ( pF ) PEAK FORWARD SURGE CURRENT, ( A ) 3.0 10 100 .01 FIG. 2 - TYPICAL FORWARD CURRENT DERATING CURVE AVERAGE FORWARD CURRENT, ( A ) FIG. 1 - TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 50 NONINDUCTIVE 8.3ms Single Half Sine-Wave (JEDEC Method) 50 40 30 20 10 0 100 60 40 UF2 001P T~U F200 20 10 TJ= 25oC 6 UF20 0 6PT~ 5PT UF20 0 7PT 4 2 1 1 2 5 10 20 NUMBER OF CYCLES AT 60 Hz 50 100 .1 .2 .4 1.0 2 4 10 20 REVERSE VOLTAGE, ( V ) 40 100