UPL81PT CHENMKO ENTERPRISE CO.,LTD THRU SURFACE MOUNT GLASS PASSIVATED SUPER FAST SILICON RECTIFIER VOLTAGE RANGE 50 - 600 Volts CURRENT 8.0 Amperes UPL86PT PROVISIONAL SPEC. FEATURE *Sm al l S u r f ac e M o u n t i n g T y p e. (SMP) * Low forward voltage, high current capability * Low leakage current * Glass passivated junction * High temperature soldering guaranteed : 260oC/10 seconds at terminals SMP 0.081 (2.05) 0.077 (1.95) 0.170 (4.31) 0.163 (4.15) (3) (1) (2) 0.019 (0.50 Min.) 0.077 (1.95) 0.073 (1.85) 0.045 (1.16) 0.042 (1.07) 0.005 (0.15 Min.) 0.019 (0.50 Min.) 0.264 (6.70) 0.254 (6.46) CIRCUIT 2 0.212 (5.38) 0.208 (5.29) 1 0.055 (1.40) 0.051 (1.30) SMP Dimensions in inches and (millimeters) 3 o MAXIMUM RATINGES ( At TA = 25 C unless otherwise noted ) UPL85PT UPL86PT UNITS Maximum Recurrent Peak Reverse Voltage RATINGS SYMBOL VRRM 50 100 200 300 400 600 Volts Maximum RMS Voltage VRMS 35 70 140 210 280 420 Volts Maximum DC Blocking Voltage VDC 50 100 200 300 400 600 Volts o Maximum Average Forward Rectified Current TL = 90 C UPL81PT UPL82PT UPL83PT UPL84PT IO 8.0 Amps IFSM 120 Amps Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Junction Capacitance (Note 1) CJ Operating and Storage Temperature Range 50 TJ, TSTG 30 pF o -55 to +150 C ELECTRICAL CHARACTERISTICS ( At TA = 25oC unless otherwise noted ) CHARACTERISTICS SYMBOL Maximum Instantaneous Forward Voltage at 8.0 A DC Maximum DC Reverse Current @ TA = 25oC at Rated DC Blocking Voltage @ TA = 100oC Maximum Reverse Recovery Time (Note 2) NOTES : 1. Measured at 1.0 MHZ and applied reverse voltage of 4.0 volts 2. Test Conditions : IF = 0.5 A, IR = -1.0 A, IRR = -0.25 A VF UPL81PT UPL82PT UPL83PT UPL84PT 0.95 1.30 UPL85PT UPL86PT 1.50 10 UNITS Volts uAmps IR 500 trr 35 uAmps 50 nSec 2004-7 FIG. 1 - TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 50 NONINDUCTIVE 10 NONINDUCTIVE trr +0.5A (-) D.U.T (+) 0 PULSE GENERATOR (NOTE 2) 25 Vdc (approx) (-) 1 NONINDUCTIVE OSCILLOSCOPE (NOTE 1) -0.25A (+) -1.0A 1cm NOTES: 1. Rise Time = 7 ns max. Input Impedance = 1 megohm. 22 pF. 2. Rise Time = 10 ns max. Source Impedlance= 50 ohms. SET TIME BASE FOR 10 nS/cm FIG. 3 - TYPICAL REVERSE CHARACTERISTICS 100 INSTANTANEOUS FORWARD CURRENT, ( A ) INSTANTANEOUS REVERSE CURRENT, (uA) TJ =125oC TJ =100oC 1.0 .1 TJ =25oC 8.0 6.4 4.8 3.2 Single Phase Half Wave 60Hz Resistive or Inductive Load 1.6 0 0 25 50 75 100 125 150 175 LEAD TEMPERATURE ( OC ) TJ =25oC UPL84PT UPL81PT~UPL83PT 10 UPL85PT~UPL86PT 1.0 .1 Pulse Width = 300uS 1% Duty Cycle .01 .01 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE, ( % ) .2 .4 .6 .8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE, ( V ) FIG. 5 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 2.0 FIG. 6 - TYPICAL JUNCTION CAPACITANCE 140 200 120 JUNCTION CAPACITANCE, ( pF ) PEAK FORWARD SURGE CURRENT, ( A ) FIG. 2 - TYPICAL FORWARD CURRENT DERATING CURVE FIG. 4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 100 10 AVERAGE FORWARD CURRENT, ( A ) RATING CHARACTERISTIC CURVES ( UPL81PT THRU UPL86PT ) 8.3ms Single Half Sine-Wave (JEDEC Method) 100 80 60 40 20 0 100 60 UPL8 1PT~ 40 UPL8 UPL8 4PT~ 20 3PT UPL8 6PT 10 6 4 TJ =25oC 2 1 1 2 5 10 20 NUMBER OF CYCLES AT 60 Hz 50 100 .1 .2 .4 1.0 2 4 10 20 REVERSE VOLTAGE, ( V ) 40 100