CIRRUS CS47048

CS47048 Data Sheet
FEATURES
The CS47048 family is a new generation of audio system-on-achip (ASOC) processors targeted at high fidelity, cost sensitive
designs. Derived from the highly successful CS48500 32-bit
fixed point audio enhancement processor family, the CS47048
further simplifies system design and reduces total system cost
by integrating the S/PDIF Rx, S/PDIF Tx, analog inputs, analog
outputs, and SRCs to simplify system design. For example, a
hardware SRC can down-sample a 192kHz S/PDIF stream to a
lower Fs to reduce memory and MIPS requirements for
processing. This integration effectively reduces the chip count
from 3 to 1 which allows smaller, less expensive board designs.
Target applications are:
— Automotive Head Units & Outboard Amplifiers
— Automotive Processors & Automotive Integration Hubs
— Digital TV
— MP3 Docking Stations
— AVR and DVD RX
— DSP Controlled Speakers (e.g. Subwoofers, Sound
Bars)
‰ Cost-effective, High-performance 32-bit DSP
—
—
—
—
300,000,000 MAC/S (multiply accumulates per second)
Dual MAC cycles per clock
72-bit accumulators are the most accurate in the industry
32K x 32-bit SRAM with three 2K blocks assignable to either
Y data or program memory.
‰ Integrated DAC & ADC Functionality
FT
— 8 Channels of DAC output: 108dB DR, 98dB THD+N
— 4 Channels of ADC input: 105dB DR, 98dB THD+N
— Integrated 5:1 analog mux feeds one stereo ADC
‰ Configurable Serial Audio Inputs/Outputs
Integrated 192 kHz S/PDIF Rx
Integrated 192 kHz S/PDIF Tx
Supports 32-bit Serial Data @ 192 kHz
Supports 32-bit audio sample I/O between DSP chips
TDM I/O modes (Up to 8 channels per line)
EN
D TIA
EL L
PH D
R
I
A
—
—
—
—
—
The CS47048 is programmed using the simple yet powerful
Cirrus proprietary DSP Composer™ GUI development and preproduction tuning tool. Processing chains may be designed
using a drag-and-drop interface to place/utilize functional
macro audio DSP primitives and custom audio filtering blocks.
The end result is a software image that is downloaded to the
DSP via serial control port.
DSP programming could not be easier for the novice or small
engineering development group. DSP Composer provides the
programmer with faster time-to-market opportunities and the
ability to implement custom code.
The CS47048 is available in a 100-pin LQFP package with
exposed pad for better thermal characteristics. Both
Commercial (0°C to +70°C) and Automotive (-40°C to +85°C)
temperature grades.
‰ Supports Different Fs Sample Rates
— Three Integrated hardware SRC blocks
— Output can be master or slave
— Supports dual-domain Fs on inputs (S/PDIF Rx and I2S)
— Supports dual-domain Fs on outputs (S/PDIF Tx and I2S)
‰ DSP Tool Set w/ Private Keys Protect Customer IP
‰ Integrated Clock Manager/PLL
— Flexibility to operate from internal PLL, external crystal,
external oscillator
Input Fs Auto Detection w/ µC Acknowledgement
Host & Boot via SPI / I2C Serial Interface
Configurable GPIOs and External Interrupt Input
1.8V Core and a 3.3V I/O that is tolerant to 5V input
Low-power Mode: 620µW
D
‰
‰
‰
‰
‰
ADC’s & DAC’s operate
in Single ended or
Differential mode
DBC
FI
See page 30 for ordering information
Clock
Manager
PLL
(I2C Slave)
Ordering Information:
Timers
GPIO
I2S /
TDM /
SPDIF
8ch
x4
DMA
4ch
PIC
ROM
RAM
SPI / I2C
Control
ROM
RAM
ROM
Peripheral Bus
S
R
C
1
Memory Bus
MUX
O
C
ADC2/3
Advance Product Information
http://www.cirrus.com
x8
ADC0/1
Stereo Inputs
On Analog in
S
R
C
2
Coyote32
text
32-bit DSP
X
N
I2S /
TDM
DAC0
DAC1
DAC2
DAC3
DAC4
DAC5
DAC6
DAC7
8ch
S
R
C
3
SRC3 has 8
independent Channels
for In or Out
x2
I2S / TDM
Y
P
RAM
x2
32K x 32-bit SRAM with three 2K blocks
Assignable to Program or Y Data memory
I2S / TDM /
SPDIF
This document contains information for a new product.
Cirrus Logic reserves the right to modify this product without notice.
Copyright 2008 Cirrus Logic
CONFIDENTIAL
OCT ’08
DS787A7
EN
D TI
EL A
L
PH D
I RA
FT
CS47048 Data Sheet
Audio SOC Processor Family
Contacting Cirrus Logic Support
For all product questions and inquiries contact a Cirrus Logic Sales Representative.
To find the one nearest to you go to www.cirrus.com.
D
IMPORTANT NOTICE
N
FI
“Advance” product information describes products that are in development and subject to development changes. Cirrus Logic, Inc. and its subsidiaries (“Cirrus”) believe that the information contained in this document is accurate and reliable. However, the information is subject to change without notice and is provided “AS IS”
without warranty of any kind (express or implied). Customers are advised to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including
those pertaining to warranty, indemnification, and limitation of liability. No responsibility is assumed by Cirrus for the use of this information, including use of this information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third parties. This document is the property of Cirrus and by
furnishing this information, Cirrus grants no license, express or implied under any patents, mask work rights, copyrights, trademarks, trade secrets or other intellectual
property rights. Cirrus owns the copyrights associated with the information contained herein and gives consent for copies to be made of the information only for use
within your organization with respect to Cirrus integrated circuits or other products of Cirrus. This consent does not extend to other copying such as copying for general
distribution, advertising or promotional purposes, or for creating any work for resale.
C
O
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). CIRRUS PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE IN
PRODUCTS SURGICALLY IMPLANTED INTO THE BODY, AUTOMOTIVE SAFETY OR SECURITY DEVICES, LIFE SUPPORT PRODUCTS OR OTHER CRITICAL
APPLICATIONS. INCLUSION OF CIRRUS PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK AND CIRRUS
DISCLAIMS AND MAKES NO WARRANTY, EXPRESS, STATUTORY OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, WITH REGARD TO ANY CIRRUS PRODUCT THAT IS USED IN SUCH A MANNER. IF THE CUSTOMER OR CUSTOMER'S
CUSTOMER USES OR PERMITS THE USE OF CIRRUS PRODUCTS IN CRITICAL APPLICATIONS, CUSTOMER AGREES, BY SUCH USE, TO FULLY INDEMNIFY CIRRUS, ITS OFFICERS, DIRECTORS, EMPLOYEES, DISTRIBUTORS AND OTHER AGENTS FROM ANY AND ALL LIABILITY, INCLUDING ATTORNEYS'
FEES AND COSTS, THAT MAY RESULT FROM OR ARISE IN CONNECTION WITH THESE USES.
Cirrus Logic, Cirrus, the Cirrus Logic logo designs, DSP Composer, and Cirrus Framework are trademarks of Cirrus Logic, Inc. All other brand and product names in
this document may be trademarks or service marks of their respective owners.
SPI is a trademark of Motorola, Inc.
I2C is a registered trademark of Philips Semiconductor.
2
Copyright 2008 Cirrus Logic
DS787A7
CS47048 Data Sheet
Audio SOC Processor Family
Table of Contents
FEATURES ......................................................................................................................... 1
1. Documentation Strategy .........................................................................................................6
2. Overview ..................................................................................................................................6
2.1 Licensing ............................................................................................................................................... 6
3. Code Overlays .........................................................................................................................7
4. Hardware Functional Description .........................................................................................8
EN
D TI
EL A
L
PH D
I RA
FT
4.1 DSP Core .............................................................................................................................................. 8
4.2 DSP Memory ......................................................................................................................................... 9
4.2.1 DMA Controller ......................................................................................................................... 9
4.3 On-chip DSP Peripherals ...................................................................................................................... 9
4.3.1 Analog to Digital Converter Port (ADC) .................................................................................... 9
4.3.2 Digital to Analog Converter Port (DAC) .................................................................................... 9
4.3.3 Digital Audio Input Port (DAI) .................................................................................................. 10
4.3.4 S/PDIF RX Input Port (DAI) .................................................................................................... 10
4.3.5 Digital Audio Output Port (DAO) ............................................................................................. 10
4.3.6 S/PDIF TX Output Port (DAO) ................................................................................................ 10
4.3.7 Sample Rate Converters (SRC) ............................................................................................. 10
4.3.8 Serial Control Port (I2C® or SPI™) .......................................................................................... 11
4.3.9 GPIO ....................................................................................................................................... 11
4.3.10 PLL-based Clock Generator ................................................................................................. 11
4.3.11 Hardware Watchdog Timer ................................................................................................... 11
4.4 DSP I/O Description .............................................................................................................................11
4.4.1 Multiplexed Pins ..................................................................................................................... 11
4.4.2 Termination Requirements ...................................................................................................... 11
4.4.3 Pads ....................................................................................................................................... 11
4.5 Application Code Security ................................................................................................................... 12
5. Characteristics and Specifications .....................................................................................13
C
O
N
FI
D
5.1 Absolute Maximum Ratings ................................................................................................................. 13
5.2 Recommended Operating Conditions ................................................................................................. 13
5.3 Digital DC Characteristics ................................................................................................................... 13
5.4 Power Supply Characteristics ............................................................................................................. 14
5.5 Thermal Data (100-Pin LQFP with Exposed Pad) ............................................................................... 14
5.6 Digital Switching Characteristics— RESET ......................................................................................... 15
5.7 Digital Switching Characteristics — XTI .............................................................................................. 15
5.8 Digital Switching Characteristics — Internal Clock .............................................................................. 16
5.9 Digital Switching Characteristics — Serial Control Port - SPI Slave Mode ......................................... 17
5.10 Digital Switching Characteristics — Serial Control Port - SPI Master Mode ..................................... 18
5.11 Digital Switching Characteristics — Serial Control Port - I2C Slave Mode2 ....................................... 19
5.12 Digital Switching Characteristics — Serial Control Port - I2C Master Mode ...................................... 20
5.13 Digital Switching Characteristics — Digital Audio Slave Input Port ................................................... 21
5.14 Digital Switching Characteristics — Digital Audio Output Port .......................................................... 22
5.15 Digital Switching Characteristics — S/PDIF RX Port ........................................................................ 23
5.16 ADC Characteristics .......................................................................................................................... 24
5.16.1 Analog Input Characteristics (Commercial) .......................................................................... 24
5.16.2 Analog Input Characteristics (Automotive) ........................................................................... 25
5.16.3 ADC Digital Filter Characteristics ......................................................................................... 27
5.17 DAC Characteristics .......................................................................................................................... 27
5.17.1 Analog Output Characteristics (Commercial) ....................................................................... 27
DS787A7
Copyright 2008 Cirrus Logic
3
CS47048 Data Sheet
Audio SOC Processor Family
5.17.2 Analog Output Characteristics (Automotive) ........................................................................ 28
5.17.3 Combined DAC Interpolation & On-chip Analog Filter Response ........................................ 29
6. Ordering Information ............................................................................................................30
7. Environmental, Manufacturing, & Handling Information ..................................................30
8. Device Pinout Diagram .........................................................................................................31
8.1 CS47048, 100-Pin LQFP Pinout Diagram ........................................................................................... 31
9. 100-pin LQFP with Exposed Pad Package Drawing .........................................................31
10. Parameter Definitions .........................................................................................................33
EN
D TI
EL A
L
PH D
I RA
FT
10.1 Dynamic Range ................................................................................................................................. 33
10.2 Total Harmonic Distortion + Noise ..................................................................................................... 33
10.3 Frequency Response ........................................................................................................................ 33
10.4 Interchannel Isolation ........................................................................................................................ 33
10.5 Interchannel Gain Mismatch .............................................................................................................. 33
10.6 Gain Error .......................................................................................................................................... 33
10.7 Gain Drift ........................................................................................................................................... 33
11. Revision History ..................................................................................................................33
Figures
C
O
N
FI
D
Figure 1. CS47048 Top-Level Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Figure 2. RESET Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 3. XTI Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 4. Serial Control Port - SPI Slave Mode Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Figure 5. Serial Control Port - SPI Master Mode Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 6. Serial Control Port - I2C Slave Mode Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 7. Serial Control Port - I2C Master Mode Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 8. Digital Audio Input (DAI) Port Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 9. Digital Audio Output Port Timing, Master Mode . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 10. Digital Audio Output Port Timing, Slave Mode . . . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 11. ADC Single-Ended Input Test Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Figure 12. ADC Differential Input Test Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Figure 13. DAC Single-Ended Output Test Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Figure 14. DAC Differential Output Test Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Figure 15. Maximum Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Figure 16. CS47048 Pinout Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 17. 100-Pin LQFP Package Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
4
Copyright 2008 Cirrus Logic
DS787A7
CS47048 Data Sheet
Audio SOC Processor Family
Tables
C
O
N
FI
D
EN
D TI
EL A
L
PH D
I RA
FT
Table 1. CS47048 Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Table 2. Device Selection Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Table 3. Memory Configurations for CS47048 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Table 4. Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Table 5. Environmental, Manufacturing, & Handling Information . . . . . . . . . . . . . . . . . . . . 30
DS787A7
Copyright 2008 Cirrus Logic
5
CS47048 Data Sheet
Audio SOC Processor Family
1. Documentation Strategy
The CS47048 Data Sheet describes the CS47048 audio processors. This document should be
used in conjunction with the following documents when evaluating or designing a system around
the CS47048 processors
Table 1. CS47048 Related Documentation
Document Name
Description
CS47048 Data Sheet
This document
Includes detailed system design information
including Typical Connection Diagrams, BootProcedures, Pin Descriptions, Etc.
AN333 - CS47048 Firmware User’s Manual
Includes detailed firmware design information
including signal processing flow diagrams and
control API information
EN
D TI
EL A
L
PH D
I RA
FT
CS47048 System Designer’s Guide
DSP Composer User’s Manual
Includes detailed configuration and usage
information for the GUI development tool.
The scope of the CS47048 Data Sheet is primarily the hardware specifications of the CS47048
family of devices. This includes hardware functionality, characteristic data, pinout, and packaging
information.
The intended audience for the CS47048 Data Sheet is the system PCB designer, MCU
programmer, and the quality control engineer.
2. Overview
N
2.1 Licensing
FI
D
The CS47048 DSP is designed to provide high-performance post-processing and mixing of analog
and digital audio. The dual clock domain provided on the PCM inputs allows for the mixing of audio
streams with different sampling frequencies. The low-power standby preserves battery life for
applications which are always on, but not necessarily processing audio, such as automotive audio
systems.
The CS47048 utilizes voltage-out DACs and is capable of supporting dual input clock domains and
dual output clock domains through the use of the internal SRCs. The CS47048 is available in a
100-pin LQFP package. Refer to Table 2 on page 7 for the input, output, and firmware
configurations for the CS47048 DSP.
C
O
Licenses are required for any 3rd party audio processing algorithms provided for the CS47048.
Please contact your local Cirrus Logic Sales representative for more information.
6
Copyright 2008 Cirrus Logic
DS787A7
CS47048 Data Sheet
Audio SOC Processor Family
3. Code Overlays
The suite of software available for the CS47048 family consists of an operating system (OS) and a
library of overlays. The overlays for the CS47048 are currently limited to post-processors. All
software components are defined below:
1. OS/Kernel - Encompasses all non-audio processing tasks, including loading data from external
serial memory, processing host messages, calling audio-processing subroutines, error
concealment, etc.
FT
2. Post-processors - Any module that processes audio I/O buffer PCM data. Examples are bass
management, audio manager, tone control, EQ, delay, customer-specific effects, and any postprocessing algorithms available for the CS485xx.
EN
D TI
EL A
L
PH D
I RA
The bulk of standard overlays are stored in ROM within the CS47048, but a small image is required
to configure the overlays and boot the DSP. This small image can either be stored in an external
serial FLASH/EEPROM, or downloaded via a host controller through the SPI™/I2C® serial port.
The overlay structure reduces the time required to reconfigure the DSP when a processing change
is requested. Each overlay can be reloaded independently without disturbing the other overlays.
For example, when a different post-processor is selected, the OS, does not need to be reloaded —
only the new post-processor.
Table 2 lists the different configuration options available. Please refer to the CS47048 Firmware
User’s Manual for the latest listing of application codes and Cirrus Framework™ modules available.
Table 2. Device Selection Guide
Suggested
Application
Device
Automotive Head Units
Automotive Outboard Amplifiers
Automotive Processors
Automotive Integration Hubs
Digital TV
MP3 Docking Stations
AVR
DVD Rx
DSP Controlled Speakers
Package
Up to 12 Channels Analog In (4 simultaneously)
Up to 10 Channels PCM In (Stand-Alone)
Up to 8 Channels PCM In (w/ Host)
100-pin
Up to 40 Channels TDM In
QFP
Up to 8 Channels Analog Out
Up to 8 Channels PCM Out
Up to 32 Channels TDM Out
C
O
N
FI
D
CS47048-CQZ
CS47048-DQZ
Channel Count
Input/Output
DS787A7
Copyright 2008 Cirrus Logic
7
CS47048 Data Sheet
Audio SOC Processor Family
4. Hardware Functional Description
The CS47048 is a true system-on-a-chip that combines a powerful 32-bit DSP engine with
analog/digital audio inputs and analog/digital audio outputs. It can be integrated into a complex
multi-DSP processing system, or stand alone in an audio product that requires analog-in and
analog-out. A top level block diagram is shown below in Figure 1.
DBC
Clock
Manager
PLL
(I2C Slave)
Timers
GPIO
I2S /
TDM /
SPDIF
8ch
I2S /
TDM
Coyote32
text
32-bit DSP
4ch
ADC2/3
Memory Bus
MUX
DMA
PIC
ROM
RAM
ROM
X
S
R
C
1
RAM
ROM
Peripheral Bus
x8
ADC0/1
Stereo Inputs
On Analog in
EN
D TI
EL A
L
PH D
I RA
x4
S
R
C
2
8ch
S
R
C
3
SRC3 has 8
independent Channels
for In or Out
x2
Y
P
DAC0
DAC1
DAC2
DAC3
DAC4
DAC5
DAC6
DAC7
FT
ADC’s & DAC’s operate
in Single ended or
Differential mode
I2S / TDM
RAM
x2
SPI / I2C
Control
FI
D
32K x 32-bit SRAM with three 2K blocks
Assignable to Program or Y Data memory
I2S / TDM /
SPDIF
N
Figure 1. CS47048 Top-Level Block Diagram
O
4.1 DSP Core
C
The CS47048 is a single-core DSP with separate X and Y data and P code memory spaces. The
DSP core is a high-performance, 32-bit, user-programmable, fixed-point DSP that is capable of
performing two multiply-and-accumulate (MAC) operations per clock cycle. The DSP core has
eight 72-bit accumulators, four X-data and four Y-data registers, and 12 index registers.
The DSP core is coupled to a flexible 8-channel DMA engine. The DMA engine can move data
between peripherals such as the serial control port (SCP), digital audio input (DAI) and digital audio
output (DAO), sample rate converters (SRC), analog-to-digital converters (ADC), digital-to-analog
converters (DAC), or any DSP core memory, all without the intervention of the DSP. The DMA
engine off-loads data move instructions from the DSP core, leaving more MIPS available for signal
processing instructions.
8
Copyright 2008 Cirrus Logic
DS787A7
CS47048 Data Sheet
Audio SOC Processor Family
CS47048 functionality is controlled by application codes that are stored in on-chip ROM or
downloaded to the CS47048 from a host controller or external serial FLASH/EEPROM.
Users can develop their applications using DSP ComposerTM to create the processing chain and
then compile the image into a series of commands that are sent to the CS47048 through the SCP.
The processing application can either load modules (post-processors) from the DSP’s on-chip
ROM, or custom firmware can be downloaded through the SCP.
The CS47048 is suitable for a variety of audio post-processing applications where sound quality via
sound enhancement and speaker/cabinet tuning is required to achieve the sound quality
consumers expect. Examples of such applications include automotive head-ends, automotive
amplifiers, docking stations, sound bars, subwoofers, and boom boxes.
4.2 DSP Memory
EN
D TI
EL A
L
PH D
I RA
FT
The DSP core has its own on-chip data and program RAM and ROM and does not require external
memory for post-processing applications.
The Y-RAM and P-RAM share a single block of memory that includes three 2K word blocks (32
bits/word) that are assignable to either Y-RAM or P-RAM as shown in Table 3.
Table 3. Memory Configurations for CS47048
P-RAM
X-RAM
Y-RAM
14K words
10K words
8K words
12K words
10K words
10K words
10K words
10K words
12K words
8K words
10K words
14K words
4.2.1 DMA Controller
The powerful 8-channel DMA controller can move data between 8 on-chip resources. Each
resource has its own arbiter: X, Y, and P RAMs/ROMs and the peripheral bus. Modulo and linear
addressing modes are supported, with flexible start address and increment controls. The service
intervals for each DMA channel, as well as up to 6 interrupt events, are programmable.
D
4.3 On-chip DSP Peripherals
FI
4.3.1 Analog to Digital Converter Port (ADC)
C
O
N
The CS47048 features ADCs with dynamic range performance in excess of 100 dB, and they can
support up to 4 simultaneous channels of analog-to-digital conversion. Analog inputs AIN_1A and
AIN_1B are connected directly to one stereo ADC (ADC0-1). The analog input capability of the
second stereo ADC (ADC2-3) is expanded through a 5:1 analog stereo mux (analog inputs
AIN_2A/B through AIN_6A/B). This gives the CS47048 the ability to select from six stereo pairs of
analog input. A single programmable bit selects single-ended or differential mode signals for all
inputs.
The conversions are performed with either Fs=96 kHz or Fs=192 kHz.
4.3.2 Digital to Analog Converter Port (DAC)
The CS47048 can support up to 8 simultaneous channels of digital-to-analog conversion and
features DACs with dynamic range performance in excess of 100 dB. The DACs have voltage
mode outputs that can be connected either as single-ended or differential signals. The conversions
are performed with Fs=96 kHz.
DS787A7
Copyright 2008 Cirrus Logic
9
CS47048 Data Sheet
Audio SOC Processor Family
4.3.3 Digital Audio Input Port (DAI)
The input capabilities for each version of the CS47048 are summarized in Table 2 on page 7.
Up to five DAI ports are available. Two of the DAI ports can be programmed to implement other
functions. The S/PDIF Rx function, if used, takes over the DAI_DATA3 pin. If the SPI mode is used,
the DAI_DATA4 pin becomes the SCP_CS input.
EN
D TI
EL A
L
PH D
I RA
FT
The DAI port supports PCM format with word lengths up to 32 bits and sample rates as high as
192 kHz.
The DAI also supports a time division multiplexed (TDM) one-line data mode that packs PCM audio
on a single data line. The total number possible depends on the ratio of SCLK to LRCLK. The
CS47048 hardware supports up to 40 channels in one line mode @ 48 kHz. There is also a
practical limitation set by the amount of processing required per channel.
The DAI port has two independent slave-only clock domains. The PCM inputs can be on one clock
domain, and the S/PDIF Rx on another. The output of the S/PDIF Rx can then be converted
through one of the internal SRC blocks to synchronize with the PCM input.
The sample rate of the input clock domains can be determined automatically by the DSP, offloading the task of monitoring the S/PDIF Rx from the host. A time-stamping feature provides the
ability to also sample-rate convert the input data via software.
4.3.4 S/PDIF RX Input Port (DAI)
One of the PCM pins of the DAI can also be used as a DC-coupled, TTL-level S/PDIF Rx input
capable of receiving and demodulating bi-phase encoded S/PDIF signals with Fs ≤ 192 kHz.
4.3.5 Digital Audio Output Port (DAO)
D
The output capabilities of the CS47048 are summarized in Table 2 on page 7.
DAO port supports PCM resolutions of up to 32-bits. The port supports sample rates (Fs) as high
as 192 kHz. The port can be configured as an independent clock domain mastered by the DSP, or
as a clock slave if an external MCLK or SCLK/LRCLK source is available.
The DAO also supports a time division multiplexed (TDM) one-line data mode, that packs multiple
channels of PCM audio on a single data line. The total number possible depends on the ratio of
SCLK to LRCLK and the version of chip. For example, the CS47048 hardware supports up to 32
channels in one line mode @ 48 kHz. There is also a practical limitation set by the amount of
processing required per channel.
4.3.6 S/PDIF TX Output Port (DAO)
N
FI
Two of the serial audio pins can be re-configured as S/PDIF TX pins that drive a bi-phase encoded
S/PDIF signal (data with embedded clock on a single line). The S/PDIF engine can be driven by a
clock domain independent of the PCM output port by utilizing one of the internal SRCs.
4.3.7 Sample Rate Converters (SRC)
C
O
The CS47048 has 3 internal SRC modules. Two of the SRC modules are capable of converting 8
Channels, and one SRC has 4-Channel capability.
The ADCs are directly associated with a 4-Channel SRC which is used to transfer data from the
fixed 96/192 kHz Fs domain into an Fs appropriate for mixing with other audio in the system. When
the Analog Inputs are not being used, this SRC can be used to convert digital data within the DSP
from the input Fs (Fsi) to the output Fs (Fso).
The DACs are directly associated with an 8-Channel SRC which is used to transfer data from the
Fs being processed by the DSP to a fixed 96 kHz Fs domain for conversion to analog. When the
Analog Outputs are not being used, this SRC can be used to convert digital data within the DSP
from Fsi to Fso.
10
Copyright 2008 Cirrus Logic
DS787A7
CS47048 Data Sheet
Audio SOC Processor Family
The second 8-Channel SRC is a stand-alone digital-to-digital conversion module. It can be used to
make independent input clock domains synchronous (different Fs on PCM input and S/PDIF Rx) or
to drive the S/PDIF Tx at a different Fs than the PCM output of the DSP.
4.3.8 Serial Control Port (I2C® or SPI™)
FT
The on-chip serial control port is capable of operating as master or slave in either SPI™ or I2C®
modes. Master/Slave operation is chosen by mode select pins when the CS47048 comes out of
reset. The serial clock pin can support frequencies as high as 25 MHz in SPI mode (SPI clock
speed must always be ≤ (DSP Core Frequency/2)). The CS47048 serial control port also includes
a pin for flow control of the communications interface (SCP_BSY) and a pin to indicate when the
DSP has a message for the host (SCP_IRQ).
4.3.9 GPIO
EN
D TI
EL A
L
PH D
I RA
Many of the CS47048 peripheral pins are multiplexed with GPIO. Each GPIO can be configured as
an output, an input, or an input with interrupt. Each input-pin interrupt can be configured as rising
edge, falling edge, active-low, or active-high.
4.3.10 PLL-based Clock Generator
The low-jitter PLL generates integer or fractional multiples of a reference frequency which are used
to clock the DSP core and peripherals. Through a second PLL divider chain, a dependent clock
domain can be output on the DAO port for driving audio converters. The CS47048 defaults to
running from the external reference frequency and is switched to use the PLL output after overlays
have been loaded and configured, either through master boot from an external FLASH or through
host control. A built-in crystal oscillator circuit with a buffered output is provided. The buffered
output frequency ratio is selectable between 1:1 (default) or 2:1.
4.3.11 Hardware Watchdog Timer
D
The CS47048 has an integrated watchdog timer that acts as a “health” monitor for the DSP. The
watchdog timer must be reset by the DSP before the counter expires, or the entire chip is reset.
This peripheral ensures that the CS47048 will reset itself in the event of a temporary system failure.
In stand-alone mode (i.e. no host MCU), the DSP will reboot from external FLASH. In slave mode
(i.e. host MCU present) a GPIO will be used to signal the host that the watchdog has expired and
the DSP should be rebooted and re-configured.
4.4 DSP I/O Description
FI
4.4.1 Multiplexed Pins
N
Many of the CS47048 pins are multi-functional. For details on pin functionality please refer to the
CS47048 System Designer’s Guide.
O
4.4.2 Termination Requirements
C
Open-drain pins on the CS47048 must be pulled high for proper operation. Please refer to the
CS47048 System Designer’s Guide to identify which pins are open-drain and what value of pull-up
resistor is required for proper operation.
Mode select pins on the CS47048 are used to select the boot mode upon the rising edge from
reset. A detailed explanation of termination requirements for each communication mode select pin
can be found in the CS47048 System Designer’s Guide.
4.4.3 Pads
The CS47048 Digital I/Os operate from the 3.3 V supply and are 5 V tolerant.
DS787A7
Copyright 2008 Cirrus Logic
11
CS47048 Data Sheet
Audio SOC Processor Family
4.5 Application Code Security
C
O
N
FI
D
EN
D TI
EL A
L
PH D
I RA
FT
The external program code may be encrypted by the programmer to protect any intellectual
property it may contain. A secret, customer-specific key is used to encrypt the program code that is
to be stored external to the device. Please contact your local Cirrus representative for details.
12
Copyright 2008 Cirrus Logic
DS787A7
CS47048 Data Sheet
Audio SOC Processor Family
5. Characteristics and Specifications
Note:
All data sheet minimum and maximum timing parameters are guaranteed over the rated voltage and
temperature. All data sheet typical parameters are measured under the following conditions: T = 25 °C,
VDD = 1.8 V, VDDIO = VDDA =3.3 V, GND = GNDIO = GNDA = 0 V.
5.1 Absolute Maximum Ratings
(GND = GNDIO = GNDA = 0 V; all voltages with respect to 0 V)
DC power supplies:
Core supply
Analog supply
I/O supply
|VDDA – VDDIO|
Symbol
Min
Max
Unit
VDD
VDDA
VDDIO
–0.3
–0.3
–0.3
-
2.0
3.6
3.6
0.3
V
V
V
V
+/- 10
mA
3.6
V
Iin
-
Vfilt
-0.3
Input voltage on digital I/O pins
Analog Input Voltage
Storage temperature
EN
D TI
EL A
L
PH D
I RA
Input pin current, any pin except supplies
Input voltage on PLL_REF_RES
FT
Parameter
Vinio
-0.3
5.0
V
Vin
AGND - 0.7
VA + 0.7
V
Tstg
–65
150
°C
Caution: Operation at or beyond these limits may result in permanent damage to the device. Normal operation is
not guaranteed at these extremes.
5.2 Recommended Operating Conditions
(GND = GNDIO = GNDA = 0 V; all voltages with respect to 0 V)
Parameter
DC power supplies:
Core supply
Analog supply
I/O supply
|VDDA – VDDIO|
Ambient operating temperature
Symbol
Min
Typ
Max
Unit
VDD
VDDA
VDDIO
1.71
3.13
3.13
1.8
3.3
3.3
0
1.89
3.46
3.46
V
V
V
V
TA
-
Commercial - CQZ
Automotive - DQZ
°C
+ 70
+ 85
D
0
- 40
Note: It is recommended that the 3.3 V IO supply come up ahead of or simultaneously with the 1.8 V core supply.
FI
5.3 Digital DC Characteristics
N
(Measurements performed under static conditions.)
Parameter
O
High-level input voltage
Low-level input voltage, except XTI
C
Low-level input voltage, XTI
Symbol
Min
Typ
Max
Unit
VIH
2.0
-
-
V
VIL
-
-
0.8
V
VILXTI
-
-
0.6
V
Input Hysteresis
Vhys
High-level output voltage (IO = -2mA), except XTO
VOH
VDDIO * 0.9
Low-level output voltage (IO = 2mA), except XTO
VOL
Input leakage XTI
ILXTI
Input leakage current (all digital pins with internal
pull-up resistors enabled)
ILEAK
DS787A7
0.4
Copyright 2008 Cirrus Logic
V
-
-
V
-
-
VDDIO * 0.1
V
-
-
5
μA
-
-
70
μA
13
CS47048 Data Sheet
Audio SOC Processor Family
5.4 Power Supply Characteristics
Note: Measurements performed under operating conditions)
Parameter
Min
Typ
Max
Unit
-
325
16
56
34
27
-
mA
mA
mA
mA
mA
Operational Power Supply Current:
VDD: Core and I/O operating1
VDDA: PLL operating current
VDDA: DAC operating current (all 8 channels enabled)
VDDA: ADC operating current (all 4 channels enabled)
VDDIO: With most ports operating
Standby Power Supply Current:
VDD: Core and I/O not clocked
VDDA: PLLs halted
VDDA: DAC disabled
VDDA: ADC disabled
VDDIO: All connected I/O pins 3-stated by other ICs in system
-
140
1.2
100
10
0.4
EN
D TI
EL A
L
PH D
I RA
Total Standby Power Dissipation:
-
FT
1025
Total Operational Power Dissipation:
mW
μA
μA
μA
μA
μA
μW
620
1. Dependent on application firmware and DSP clock speed.
5.5 Thermal Data (100-Pin LQFP with Exposed Pad)
Parameter
Symbol
Thermal Resistance (Junction to Ambient)
Two-layer Board1
Four-layer Board2
Typ
Max
-
34
18
-
-
0.54
.28
-
θja
Unit
°C / Watt
ψjt
°C / Watt
D
Thermal Resistance (Junction to Top of Package)
Two-layer Board1
Four-layer Board2
Min
1. To calculate the die temperature for a given power dissipation:
FI
Τj = Ambient temperature + [ (Power Dissipation in Watts) * θja ]
2. To calculate the case temperature for a given power dissipation:
N
Τc = Τj - [ (Power Dissipation in Watts) * ψ jt ]
O
Note: Two-layer board is specified as a 76 mm X 114 mm, 1.6 mm thick FR-4 material with 1-oz. copper covering 20%
of the top & bottom layers.
C
Note: Four-layer board is specified as a 76 mm X 114 mm, 1.6 mm thick FR-4 material with 1-oz. copper covering 20%
of the top & bottom layers and 0.5-oz. copper covering 90% of the internal power plane & ground plane layers.
14
Copyright 2008 Cirrus Logic
DS787A7
CS47048 Data Sheet
Audio SOC Processor Family
5.6 Digital Switching Characteristics— RESET
Parameter
Symbol
Min
Max
Unit
Trstl
1
-
μs
All bidirectional pins high-Z after RESET low
Trst2z
-
100
ns
Configuration pins setup before RESET high
Trstsu
50
-
ns
Configuration pins hold after RESET high
Trsthld
20
-
ns
FT
RESET minimum pulse width low
EN
D TI
EL A
L
PH D
I RA
RESET
HS[3:0]
All Bidirectional
Pins
Trstsu Trsthld
Trst2z
Trstl
Figure 2. RESET Timing
5.7 Digital Switching Characteristics — XTI
Parameter
Symbol
Min
External Crystal operating frequency1
Fxtal
XTI period
Tclki
XTI high time
D
XTI low time
2
External Crystal Load Capacitance (parallel resonant)
Unit
11.2896
27
MHz
37
89
ns
Tclkih
13.3
-
ns
Tclkil
13.3
-
ns
CL
10
18
pF
50
Ω
ESR
FI
External Crystal Equivalent Series Resistance
Max
C
O
N
1. Part characterized with the following crystal frequency values: 11.2896, 12.288, 18.432, 24.576, & 27 MH.z
2. CL refers to the total load capacitance as specified by the crystal manufacturer. Crystals which require a CL outside
this range should be avoided. The crystal oscillator circuit design should follow the crystal manufacturer’s
recommendation for load capacitor selection.
XTI
t clkih
t clkil
Tclki
Figure 3. XTI Timing
DS787A7
Copyright 2008 Cirrus Logic
15
CS47048 Data Sheet
Audio SOC Processor Family
5.8 Digital Switching Characteristics — Internal Clock
Parameter
Internal DSP_CLK
frequency1
Symbol
Min
Max
Fdclk
Fxtal2
Fxtal
150
150
6.7
6.7
1/Fxtal
1/Fxtal
CS47048-CQZ
CS47048-DQZ
Internal DSP_CLK period1
DCLKP
CS47048-CQZ
CS47048-DQZ
Unit
MHz
ns
C
O
N
FI
D
EN
D TI
EL A
L
PH D
I RA
FT
1. After initial power-on reset, Fdclk = Fxtal. After initial kickstart commands, the PLL is locked to max Fdclk and remains
locked until the next power-on reset.
2.See Section 5.7.
16
Copyright 2008 Cirrus Logic
DS787A7
CS47048 Data Sheet
Audio SOC Processor Family
5.9 Digital Switching Characteristics — Serial Control Port - SPI Slave Mode
Min
SCP_CLK frequency1
fspisck
SCP_CS falling to SCP_CLK rising
Typical
Max
Units
-
25
MHz
tspicss
24
-
ns
SCP_CLK low time
tspickl
20
-
ns
SCP_CLK high time
tspickh
20
-
ns
Setup time SCP_MOSI input
tspidsu
5
-
ns
Hold time SCP_MOSI input
tspidh
5
-
ns
SCP_CLK low to SCP_MISO output valid
tspidov
-
11
ns
SCP_CLK falling to SCP_IRQ rising
tspiirqh
-
SCP_CS rising to SCP_IRQ falling
tspiirql
0
SCP_CLK low to SCP_CS rising
tspicsh
24
SCP_CS rising to SCP_MISO output high-Z
tspicsdz
-
20
ns
SCP_CLK rising to SCP_BSY falling
tspicbsyl
-
3*DCLKP+20
ns
FT
Symbol
20
EN
D TI
EL A
L
PH D
I RA
Parameter
-
ns
ns
ns
1. fspisck indicates the maximum speed of the hardware. The system designer should be aware that the actual
maximum speed of the communication port may be limited by the firmware application. Flow control using the
SCP_BSY pin should be implemented to prevent overflow of the input data buffer. At boot the maximum speed is
Fxtal/3.
tspicss
SCP_CS
tspickl
1
0
1/ fspisck
A6
A5
FI
SCP_MOSI
D
SCP_CLK
2
6
7
0
A0
R/W
MSB
5
7
6
tspicsh
tspickh
LSB
tspidh
tspidov
tspicsdz
MSB
O
SCP_MISO
N
tspidsu
LSB
C
tspiirqh
tspiirql
SCP_IRQ
tspibsyl
SCP_BSY
Figure 4. Serial Control Port - SPI Slave Mode Timing
DS787A7
Copyright 2008 Cirrus Logic
17
CS47048 Data Sheet
Audio SOC Processor Family
5.10 Digital Switching Characteristics — Serial Control Port - SPI Master Mode
Symbol
Min
Max
Units
fspisck
-
Fxtal/22
MHz
tspicss
-
-
ns
SCP_CLK low time
tspickl
18
-
ns
SCP_CLK high time
tspickh
18
-
ns
Setup time SCP_MISO input
tspidsu
9
-
ns
Hold time SCP_MISO input
tspidh
5
-
ns
SCP_CLK low to SCP_MOSI output valid
tspidov
-
8
ns
SCP_CLK low to SCP_CS falling
tspicsl
7
-
ns
11*DCLKP +
(SCP_CLK PERIOD)/2
-
ns
3*DCLKP
-
ns
20
ns
SCP_CLK frequency1
SCP_CLK low to SCP_CS rising
tspicsh
Bus free time between active SCP_CS
11*DCLKP +
(SCP_CLK PERIOD)/2
EN
D TI
EL A
L
PH D
I RA
SCP_CS falling to SCP_CLK rising
3
Typical
FT
Parameter
-
tspicsx
SCP_CLK falling to SCP_MOSI output high-Z
tspidz
-
1. fspisck indicates the maximum speed of the hardware. The system designer should be aware that the actual
maximum speed of the communication port may be limited by the firmware application.
2. See Section 5.7.
3. SCP_CLK PERIOD refers to the period of SCP_CLK as being used in a given application. It does not refer to a
tested parameter
tspicss
D
EE_CS
tspicsl
1
FI
SCP_CLK
0
N
1/ fspisck
C
O
SCP_MISO
SCP_MOSI
A6
A5
tspickl
2
6
7
0
A0
R/W
MSB
5
7
6
tspicsx
tspicsh
tspickh
LSB
tspidsu
tspidh
tspidov
tspidz
MSB
LSB
Figure 5. Serial Control Port - SPI Master Mode Timing.
18
Copyright 2008 Cirrus Logic
DS787A7
CS47048 Data Sheet
Audio SOC Processor Family
5.11 Digital Switching Characteristics — Serial Control Port - I2C Slave Mode2
Symbol
Min
SCP_CLK frequency
fiicck
-
SCP_CLK rise time
Max
Units
400
kHz
tiicr
150
ns
SCP_CLK fall time
tiicf
150
ns
SCP_CLK low time
tiicckl
1.25
-
µs
SCP_CLK high time
tiicckh
1.25
-
µs
tiicckcmd
1.25
START condition to SCP_CLK falling
tiicstscl
1.25
SCP_CLK falling to STOP condition
tiicstp
2.5
Bus free time between STOP and START conditions
tiicbft
3
Setup time SCP_SDA input valid to SCP_CLK rising
tiicsu
100
Hold time SCP_SDA input after SCP_CLK falling
tiich
20
-
ns
tiicdov
-
18
ns
tiicirqh
-
3*DCLKP + 40
ns
SCP_CLK low to SCP_SDA out valid
SCP_CLK falling to SCP_IRQ rising
NAK condition to SCP_IRQ low
EN
D TI
EL A
L
PH D
I RA
SCP_CLK rising to SCP_SDA rising or falling for START or STOP
condition
tiicirql
SCP_CLK rising to SCB_BSY low
Typical
tiicbsyl
-
µs
FT
Parameter
1
-
µs
-
µs
-
µs
ns
3*DCLKP + 20
ns
3*DCLKP + 20
ns
1. fiicck indicates the maximum speed of the hardware. The system designer should be aware that the actual maximum
speed of the communication port may be limited by the firmware application. Flow control using the SCP_BSY pin
should be implemented to prevent overflow of the input data buffer.
2. I2C Slave Address = 0x82
tiicckl
D
tiicckcmd
Start Condition
SCP_CLK
A6
tiicf
7
8
0
tiicdov
A0
R/W
1
6
7
ACK
MSB
Stop Condition
tiicstp
LSB
tiicbft
ACK
tiicirqh
tiicsu
tiicckcmd
8
1/ fiicck
tiicirql
tiich
C
O
SCP_SDA
6
tiicckh
N
tiicstscl
1
FI
0
tiicr
SCP_IRQ
tiiccbsyl
SCP_BSY
Figure 6. Serial Control Port - I2C Slave Mode Timing
DS787A7
Copyright 2008 Cirrus Logic
19
CS47048 Data Sheet
Audio SOC Processor Family
5.12 Digital Switching Characteristics — Serial Control Port - I2C Master Mode
Symbol
Min
Max
Units
SCP_CLK frequency1
fiicck
-
400
kHz
SCP_CLK rise time
tiicr
-
150
ns
SCP_CLK fall time
tiicf
-
150
ns
SCP_CLK low time
tiicckl
1.25
-
µs
SCP_CLK high time
tiicckh
1.25
-
µs
tiicckcmd
1.25
START condition to SCP_CLK falling
tiicstscl
1.25
SCP_CLK falling to STOP condition
tiicstp
2.5
Bus free time between STOP and START conditions
tiicbft
3
Setup time SCP_SDA input valid to SCP_CLK rising
tiicsu
100
tiich
20
-
ns
tiicdov
-
18
ns
Hold time SCP_SDA input after SCP_CLK falling
SCP_CLK low to SCP_SDA out valid
µs
EN
D TI
EL A
L
PH D
I RA
SCP_CLK rising to SCP_SDA rising or falling for START or STOP condition
-
µs
-
µs
-
µs
FT
Parameter
ns
1.fiicck indicates the maximum speed of the hardware. The system designer should be aware that the actual maximum speed of the
communication port may be limited by the firmware application.
tiicckcmd
tiicckl
0
1
SCP_CLK
tiicstscl
tiicr
6
tiicckh
A6
0
R/W
1
6
7
8
1/ fiicck
tiicdov
A0
tiich
8
ACK
MSB
LSB
tiicstp
tiicbft
ACK
FI
tiicsu
7
tiicckcmd
D
SCP_SDA
tiicf
C
O
N
Figure 7. Serial Control Port - I2C Master Mode Timing
20
Copyright 2008 Cirrus Logic
DS787A7
CS47048 Data Sheet
Audio SOC Processor Family
5.13 Digital Switching Characteristics — Digital Audio Slave Input Port
Parameter
DAI_SCLK period
Symbol
Min
Max
Unit
Tdaiclkp
20
-
ns
-
45
55
%
Setup time DAI_DATAn
tdaidsu
8
-
ns
Hold time DAI_DATAn
tdaidh
5
-
ns
DAI_SCLK
tdaidh
EN
D TI
EL A
L
PH D
I RA
tdaidsu
FT
DAI_SCLK duty cycle
DAI_DATAn
C
O
N
FI
D
Figure 8. Digital Audio Input (DAI) Port Timing Diagram
DS787A7
Copyright 2008 Cirrus Logic
21
CS47048 Data Sheet
Audio SOC Processor Family
5.14 Digital Switching Characteristics — Digital Audio Output Port
Parameter
DAO_MCLK period
Symbol
Min
Max
Unit
Tdaomclk
20
-
ns
DAO_MCLK duty cycle
-
45
55
%
Tdaosclk
20
-
ns
-
40
60
%
tdaomsck
-
19
ns
DAO_LRCLK to DAO_SCLK non-active edge3, See Figure 9A.
tdaomlrts
-
8
ns
DAO_SCLK non-active edge3 to DAO_LRCLK, See Figure 9B
tdaomstlr
-
8
ns
tdaomdv
-
8
ns
DAO_SCLK period for Master or Slave mode1
DAO_SCLK duty cycle for Master or Slave mode1
DAO_SCLK delay from DAO_MCLK rising edge,
DAO_MCLK as an input
DAO_DATA[3..0] delay from DAO_SCLK non-active
Mode)4
EN
D TI
EL A
L
PH D
I RA
Slave Mode (Output A0
edge3
DAO_LRCLK to DAO_SCLK non-active edge3, See Figure 10A.
DAO_SCLK non-active
edge3
to DAO_LRCLK, See Figure 10B.
.
FT
Master Mode (Output A1 Mode)
1,2
DAO1_DATA[3..0] delay from DAO_SCLK non-active edge3
tdaoslrts
-
15
ns
tdaosstlr
-
30
ns
tdaosdv
-
8
ns
1. Master mode timing specifications are characterized, not production tested.
2. Master mode is defined as the CS47048 driving both DAO_SCLK, DAO_LRCLK. When MCLK is an input, it
is divided to produce DAO_SCLK, DAO_LRCLK.
3. The DAO_LRCLK transition may occur on either side of the non-active edge of DAO_LRCLK. The active edge
of DAO_SCLK is the point at which the data is valid.
4. Slave mode is defined as DAO_SCLK, DAO_LRCLK driven by an external source.
tdaomclk
tdaomclk
DAO_MCLK
DAO_MCLK
tdaomsck
D
tdaomsck
N
FI
DAO_SCLK
DAO_SCLK
DAO_LRCLK
O
DAO_LRCLK
tdaomdv
tdaomdv
DAO_DATAn
DAO_DATAn
C
tdaomstlr
tdaomlrts
A. DAO_LRCLK transition before DAO_SCLK non-active
edge. See Footnote 3 on page 22.
B. DAO_LRCLK transition after DAO_SCLK non-active
edge. See Footnote 3 on page 22.
Figure 9. Digital Audio Output Port Timing, Master Mode
22
Copyright 2008 Cirrus Logic
DS787A7
CS47048 Data Sheet
Audio SOC Processor Family
tdaosclk
t dao sclk
D AO _SCLK
DAO_SCLK
t daosstlr
tdaoslrts
DAO _LRC LK
DAO_LRCLK
t d aosdv
tdaosdv
DAO _D ATAn
FT
DAOn_DATAn
B. DAO_LRCLK transition after DAO_SCLK nonactive edge. See Footnote 3 on page 22.
EN
D TI
EL A
L
PH D
I RA
A. DAO_LRCLK transition before DAO_SCLK
non-active edge. See Footnote 3 on page 22.
Figure 10. Digital Audio Output Port Timing, Slave Mode
5.15 Digital Switching Characteristics — S/PDIF RX Port
(Inputs: Logic 0 = VIL, Logic 1 = VIH; CL = 20 pF)
Parameter
Symbol
Typ
Max
Units
30
-
200
kHz
C
O
N
FI
D
PLL Clock Recovery Sample Rate Range
Min
DS787A7
Copyright 2008 Cirrus Logic
23
CS47048 Data Sheet
Audio SOC Processor Family
5.16 ADC Characteristics
5.16.1 Analog Input Characteristics (Commercial)
(Test Conditions (unless otherwise specified): TA = 0 to +70°C; VDD = 1.8 V±5%, VDDA (VA)= 3.3 V±5%; 1 kHz
sine wave driven through the passive input filter (Ri=10kΩ) in Figure 11 on page 26 or Figure 12 on page 26; DSP
running test application; Measurement Bandwidth is 10 Hz to 20 kHz.)
Differential
Dynamic Range1,6,7
A-weighted
unweighted
40 kHz bandwidth unweighted
Full-Scale Input Voltage2,3
Differential Input Impedance4
Single-Ended Input Impedance5
Common Mode Rejection Ratio (CMRR)8
Max
Min
Typ
Max
Unit
99
96
-
105
102
99
-
96
93
102
99
96
-
dB
dB
dB
-
-98
-82
-42
-90
-92
-
-
-95
-79
-39
-90
-89
-
dB
dB
dB
dB
-
95
95
-
-
95
95
-
dB
dB
-
0.1
±120
-
-
0.1
±120
-
dB
ppm/°C
3.3•VA
3.5•VA
3.7•VA
-
400
-
-
-
-
Ω
-
-
-
-
200
-
Ω
-
60
-
-
-
-
dB
-
-
20
-
-
20
pF
1.65•VA 1.75•VA 1.85•VA
VPP
C
O
N
FI
D
Parasitic Load Capacitance
(CL)9
Typ
EN
D TI
EL A
L
PH D
I RA
Total Harmonic Distortion + Noise6,7 -1 dB
-20 dB
-60 dB
40 kHz bandwidth
-1 dB
AIN_1A/B Interchannel Isolation
AIN_[2..6]A/B MUX Interchannel Isolation
DC Accuracy
Interchannel Gain Mismatch
Gain Drift
Analog Input
Min
FT
Parameter
Fs= 96 kHz, 192 kHz
Single-Ended
24
Copyright 2008 Cirrus Logic
DS787A7
CS47048 Data Sheet
Audio SOC Processor Family
5.16.2 Analog Input Characteristics (Automotive)
(Test Conditions (unless otherwise specified): TA = -40 to +85°C; VDD = 1.8 V±5%, VDDA (VA)= 3.3 V±5%; 1 kHz
sine wave driven through the passive input filter (Ri=10kΩ) in Figure 11 on page 26 or Figure 12 on page 26; DSP
running test application; Measurement Bandwidth is 10 Hz to 20 kHz.)
Differential
Single-Ended
Min
Typ
Max
Unit
-
94
91
102
99
96
-
dB
dB
dB
-98
-82
-42
-90
-90
-
-
-95
-79
-39
-90
-87
-
dB
dB
dB
dB
-
95
95
-
-
95
95
-
dB
dB
-
0.1
±120
-
-
0.1
±120
-
dB
ppm/°C
3.24•VA
3.5•VA
-
400
-
-
-
-
Ω
-
-
-
-
200
-
Ω
Common Mode Rejection Ratio (CMRR)8
-
60
-
-
-
-
dB
Parasitic Load Capacitance (CL)9
-
-
20
-
-
20
pF
Dynamic Range1,6,7
A-weighted
unweighted
40 kHz bandwidth unweighted
Full-Scale Input Voltage2,3
Differential Input
Impedance4
Single-Ended Input Impedance5
Notes:
Typ
Max
97
94
-
105
102
99
-
EN
D TI
EL A
L
PH D
I RA
Total Harmonic Distortion + Noise6,7 -1 dB
-20 dB
-60 dB
40 kHz bandwidth
-1 dB
AIN_1A/B Interchannel Isolation
AIN_[2..6]A/B MUX Interchannel Isolation
DC Accuracy
Interchannel Gain Mismatch
Gain Drift
Analog Input
Min
FT
Parameter
Fs=96 kHz, 192 kHz
3.76•VA 1.62•VA 1.75•VA 1.88•VA
VPP
D
1. dB units referred to the typical full-scale voltage.
2. These full-scale values were measured with Ri=10k for both the single-ended and differential mode input circuits.
FI
3. The full-scale voltage can be changed be scaling Ri.
Differential Full-Scale (Vpp) = (Ri+200)/(10k+200)*3.5*VDDA
Single-Ended Full-Scale (Vpp) = (Ri+200)/(10k+200)*1.75*VDDA
N
4. Measured between AIN_xx+ and AN_xx-.
5. Measured between AIN_xx+ and AGND.
6. Decreasing Full-Scale voltage by reducing Ri will cause the noise floor to increase.
O
7. Common mode input current should be kept to less than +/- 160uA to avoid performance degradation: |(Iip+Iin)/2| <
160uA. This corresponds to +/- 1.6V for Ri=10kΩ in the differential case.
C
8. This number was measured using perfectly matched external resistors (Ri). Mismatch in the external resistors will
typically reduce CMRR by 20 log (|ΔRi|/Ri + 0.001).
9. CL represents the parasitic load capacitance between Ri on the input circuit and the input pin of the CS47048
package.
DS787A7
Copyright 2008 Cirrus Logic
25
CS47048 Data Sheet
Audio SOC Processor Family
10µF
100K
CL
AIN_xA+
or
AIN_xB+
EN
D TI
EL A
L
PH D
I RA
Figure 11. ADC Single-Ended Input Test Circuit
FT
Ri
AIN
10µF
AIN-
Ri
100K
CL
AIN_xAor
AIN_xB-
10µF
AIN+
Ri
100K
CL
AIN_xA+
or
AIN_xB+
C
O
N
FI
D
Figure 12. ADC Differential Input Test Circuit
26
Copyright 2008 Cirrus Logic
DS787A7
CS47048 Data Sheet
Audio SOC Processor Family
5.16.3 ADC Digital Filter Characteristics
Parameter1, 2
Max
Unit
0
0.5688
70
-
12/Fs
0.4896
0.08
-
Fs
dB
Fs
dB
s
-
1
20
10
5
10 /Fs
0
0
Hz
Hz
Deg
dB
s
-
EN
D TI
EL A
L
PH D
I RA
Notes:
to -0.1 dB corner
Typ
FT
Fs = 96 kHz, 192 kHz
Passband (Frequency Response)
Passband Ripple
Stopband
Stopband Attenuation
Total Group Delay
High-Pass Filter Characteristics
Frequency Response
-3.0 dB
-0.13 dB
Phase Deviation
@ 20 Hz
Passband Ripple
Filter Settling Time
Min
1. Filter response is guaranteed by design.
2. Response is clock-dependent and will scale with Fs.
5.17 DAC Characteristics
5.17.1 Analog Output Characteristics (Commercial)
(Test Conditions (unless otherwise specified): TA = 0 to +70°C; VDD = 1.8V±5%, VDDA(VA) = 3.3V±5%; 1 kHz
sine wave driven through a filter shown in Figure 13 on page 28 or Figure 14 on page 29; DSP running test application; Measurement Bandwidth is 20 Hz to 20 kHz.)
Parameter
Fs = 96 kHz
Dynamic Range
C
O
N
FI
D
A-weighted
unweighted
Total Harmonic Distortion + Noise
0 dB
-20 dB
-60 dB
Interchannel Isolation
(1 kHz)
Analog Output
Full-Scale Output
Interchannel Gain Mismatch
Gain Drift
Output Impedance
DC Current draw from an AOUT pin1
AC-Load Resistance (RL)2
Load Capacitance (CL)2
DS787A7
Min
Differential
Typ
102
99
108
105
-
99
96
105
102
-
dB
dB
-
-98
-88
-48
95
-90
-
-
-95
-85
-45
95
-87
-
dB
dB
dB
dB
TBD
-
1.35•VA
0.1
±120
100
-
TBD
10
TBD
-
0.68•VA
0.1
±120
100
-
TBD
10
VPP
dB
ppm/°C
Ω
μA
3
-
-
100
3
-
-
100
kΩ
pF
Max
Copyright 2008 Cirrus Logic
Min
Single-Ended
Typ
Max
Unit
27
CS47048 Data Sheet
Audio SOC Processor Family
5.17.2 Analog Output Characteristics (Automotive)
(Test Conditions (unless otherwise specified): TA = -40 to +85°C; VDD = 1.8V±5%, VDDA(VA) = 3.3V±5%; 1 kHz
sine wave driven through a filter shown in Figure 13 on page 28 or Figure 14 on page 29; DSP running test application; Measurement Bandwidth is 20 Hz to 20 kHz.)
Min
Differential
Typ
100
97
108
105
-
97
94
105
102
-
-98
-88
-48
95
-90
-
-
-95
-85
-45
95
-87
-
dB
dB
dB
dB
TBD
-
1.35•VA
0.1
±120
100
-
TBD
10
TBD
-
0.68•VA
0.1
±120
100
-
TBD
10
VPP
dB
ppm/°C
Ω
μA
3
-
-
3
-
-
kΩ
-
-
100
-
-
100
pF
Parameter
Max
Min
Single-Ended
Typ
Max
Unit
Fs = 96 kHz
Dynamic Range
DC Current draw from an AOUT pin1
AC-Load Resistance (RL)2
Load Capacitance (CL)2
Notes:
-
FT
EN
D TI
EL A
L
PH D
I RA
A-weighted
unweighted
Total Harmonic Distortion + Noise
0 dB
-20 dB
-60 dB
Interchannel Isolation
(1 kHz)
Analog Output
Full-Scale Output
Interchannel Gain Mismatch
Gain Drift
Output Impedance
dB
dB
C
O
N
FI
D
1. Guaranteed by design. The DC current draw represents the allowed current draw from the AOUT pin due to typical
leakage through the electrolytic DC-blocking capacitors.
2. Guaranteed by design. RL and CL reflect the recommended minimum resistance and maximum capacitance
required for the internal op-amp's stability and signal integrity. In this circuit topology, CL represents any capacitive
loading that appears before the 560Ω series resistor (typically parasitic), and will effectively move the dominant pole
of the two-pole amp in the output stage. Increasing this value beyond the recommended 100 pF can cause the
internal op-amp to become unstable.
3.3 µF
560
AOUT
AOUT_x+
CL
RL
10k
2200pF
Figure 13. DAC Single-Ended Output Test Circuit
28
Copyright 2008 Cirrus Logic
DS787A7
CS47048 Data Sheet
Audio SOC Processor Family
4.87k
1800pF
4.87k
2.43k
1.96k
953
CL
+
CL
AOUT
10k
+
22µF
1200pF
FT
4700pF
560
22µF
1.96k
AOUT_x+
-
+
AOUT_x-
470pF
P output: RL = 1.96k + ( [2πF*4700-12 ]-1 || (1.96k + [2πF*22-6 ]-1 ) || (953 + [2πF*1200-12 ]-1 ))
EN
D TI
EL A
L
PH D
I RA
N output: RL = 4.87k + ( [2πF*1800-12 ]-1 || ((2.43k + [2πF*470-12 ]-1 ) || 4.87k ))
Figure 14. DAC Differential Output Test Circuit
Capacitive Load -- C L (pF)
125
100
75
Safe Operating
Region
50
25
5
2.5
3
10
15
20
Figure 15. Maximum Loading
N
FI
D
Resistive Load -- RL (kΩ )
O
5.17.3 Combined DAC Interpolation & On-chip Analog Filter Response
Parameter
C
Passband (Frequency Response)
to 0.22 dB corner
to -3 dB corner
Frequency Response 10 Hz to 20 kHz
StopBand
StopBand Attenuation
Group Delay
DS787A7
Copyright 2008 Cirrus Logic
Min
Typ
Max
Unit
0
0
-0.02
0.5465
100
-
10/Fs
0.4125
0.4979
+0.02
-
Fs
Fs
dB
Fs
dB
s
29
CS47048 Data Sheet
Audio SOC Processor Family
6. Ordering Information
The CS47048 DSP part numbers are described as follows:
CS47048I-XYZR
where
I - ROM ID Letter
X - Product Grade
Y - Package Type
Z - Lead (Pb) Free
FT
R - Tape and Reel Packaging
Part No.
CS47048B-CQZ
EN
D TI
EL A
L
PH D
I RA
Table 4. Ordering Information
Grade
Temp. Range
Commercial
0 to +70 °C
Automotive
-40 to +85 °C
Package
100-pin LQFP
CS47048B-DQZ
NOTE: Please contact the factory for availability of the -D (automotive grade) package.
7. Environmental, Manufacturing, & Handling Information
Table 5. Environmental, Manufacturing, & Handling Information
Model Number
CS47048B-CQZ
CS47048B-DQZ
Peak Reflow Temp
MSL Rating*
Max Floor Life
260 °C
3
7 days
C
O
N
FI
D
* MSL (Moisture Sensitivity Level) as specified by IPC/JEDEC J-STD-020.
30
Copyright 2008 Cirrus Logic
DS787A7
CS47048 Data Sheet
Audio SOC Processor Family
8. Device Pinout Diagram
DBCK
AOUT_8-
AOUT_8+
76
GNDA4
VDDA4
AOUT_7-
AOUT_7+
80
AOUT_6-
AOUT_6+
GNDA5
VDDA5
AOUT_5-
85
AOUT_5+
AOUT_4-
AOUT_4+
GNDA6
VDDA6
90
AOUT_3-
AOUT_3+
AOUT_2-
AOUT_2+
GNDA7
95
VDDA7
AOUT_1+
AOUT_1-
100 RESET
8.1 CS47048, 100-Pin LQFP Pinout Diagram
1
75 VDD_DAC
DBDA
GND_DAC
VDD_ADC_MON
GPIO15, DAI_LRCLK
REXT
GPIO17, DAI_SCLK
5
FT
VQ
70 BIASREF_DAC
GNDIO1
GPIO16, DAI_DATA0, TM0
GNDA3
GPIO0, DAI_DATA1, TM1
AIN_1A+
AIN_1A-
10
VDD1
GND1
CS47048
GPIO7, DAO_LRCLK
GPIO14, DAO_SCLK
VDDA3
BIASREF_ADC
VDDA2
GNDA2
60 AIN_2A+
AIN_2AAIN_3A+
AIN_3AAIN_4A+
55 AIN_4AAIN_5A+
AIN_5AAIN_6A+
50
51 AIN_6A-
AIN_2B+
AIN_2B-
AIN_3B-
AIN_4B+
AIN_4B- 45
AIN_5B+
AIN_5B-
AIN_6B+
GND3
XTAL_OUT
GND_SUB
AIN_1B+
65 AIN_1B-
Figure 16. CS47048 Pinout Diagram
O
N
FI
D
GPIO11, SCP_CLK
GPIO8, SCP_CS, DAI_DATA4
GNDIO3
30
25
26
GPIO10, SCP_MISO, SCP_SDA
AIN_6B-
GPIO9, SCP_MOSI
40
VDD2
GND2
VDDA_PLL
GPIO5, DAO_DATA3, HS3, S/PDIF TXa
PLL_REF_RES
20
VDDIO3
GPIO4, DAO_DATA2, HS2, S/PDIF TXb
GNDA_PLL
GPIO3, DAO_DATA1, HS1
XTO
GPIO6, DAO_DATA0, HS0
XTI
GPIO18, DAO_MCLK, HS4
VDD3
VDDIO2
35
100-Pin LQFP
15
GPIO13, SCP_BSY, EE_CS
GNDIO2
GPIO12, SCP_IRQ
GPIO2, DAI_DATA3, TM3, SPDIF RX
EN
D TI
EL A
L
PH D
I RA
GPIO1, DAI_DATA2, TM2
AIN_3B+
VDDIO1
C
9. 100-pin LQFP with Exposed Pad Package Drawing
Figure 17 shows the CS47048 100-pin LQFP package with exposed pad.
DS787A7
Copyright 2008 Cirrus Logic
31
DS787A7
C
O
N
FI
D
AF
T
32
CS47048 Data Sheet
Audio SOC Processor Family
R
D
AL H I
TI P
L
EN E
D
Copyright 2008 Cirrus Logic
Figure 17. 100-Pin LQFP Package Drawing
CS47048 Data Sheet
Audio SOC Processor Family
10. Parameter Definitions
10.1 Dynamic Range
The ratio of the RMS value of the signal to the RMS sum of all other spectral components over the
specified bandwidth. Dynamic Range is a signal-to-noise ratio measurement over the specified
bandwidth made with a -60 dBFS signal. 60 dB is added to resulting measurement to refer the
measurement to full-scale. This technique ensures that the distortion components are below the
noise level and do not affect the measurement. This measurement technique has been accepted
by the Audio Engineering Society, AES17-1991, and the Electronic Industries Association of
Japan, EIAJ CP-307. Expressed in decibels.
FT
10.2 Total Harmonic Distortion + Noise
10.3 Frequency Response
EN
D TI
EL A
L
PH D
I RA
The ratio of the RMS value of the signal to the RMS sum of all other spectral components over the
specified bandwidth (typically 10 Hz to 20 kHz), including distortion components. Expressed in
decibels. Measured at -1 and -20 dBFS as suggested in AES17-1991 Annex A.
A measure of the amplitude response variation from 10 Hz to 20 kHz relative to the amplitude
response at 1 kHz. Units in decibels.
10.4 Interchannel Isolation
A measure of crosstalk between the left and right channels. Measured for each channel at the
converter's output with no signal to the input under test and a full-scale signal applied to the other
channel. Units in decibels.
10.5 Interchannel Gain Mismatch
The gain difference between left and right channels. Units in decibels.
10.6 Gain Error
The deviation from the nominal full-scale analog output for a full-scale digital input.
10.7 Gain Drift
FI
D
The change in gain value with temperature. Units in ppm/°C.
Date
O
Revision
N
11. Revision History
October 16, 2008
Initial Release
C
A7
Changes
DS787A7
Copyright 2008 Cirrus Logic
33
C
O
N
FI
D
EN
D TI
EL A
L
PH D
I RA
FT
CS47048 Data Sheet
Audio SOC Processor Family
34
Copyright 2008 Cirrus Logic
DS787A7