VRE310 VRE310 P r o d u c t IInnnnoovvaa t i o n FFr roomm Precision Voltage Reference Features ♦ +10 V Output, ±1.0 mV (.01%) ♦ Temperature Drift: 0.6 ppm/ºC ♦ Low Noise: 6 μVP-P (0.1-10Hz) ♦ Industry Standard Pinout: 8-pin DIP or Surface Mount Package ♦ Excellent Line Regulation: 6 ppm/V Typical ♦ Output Trim Capability Applications The VRE310 is recommended for use as a reference for 14, 16, or 18-bit D/A converters which require an external precision reference. The device is also ideal for calibrating scale factor on high resolution A/D converters. The VRE310 offers superior performance over monolithic references. DESCRIPTION The VRE310 is a low cost, high precision +10 V reference. Available in an industry standard 8-pin DIP or SMT, the device is ideal for upgrading systems that use lower performance references. The device provides ultrastable +10 V output with ±1.0 mV (.01%) initial accuracy and a temperature coefficient of 0.6 ppm/ºC. This improvement in accuracy is made possible by a unique, patented multipoint laser compensation technique. Significant improvements have been made in other performance parameters as well, including initial accuracy, warm-up drift, line regulation, and long-term stability, making the VRE310 series the most accurate reference available in a standard 8-pin DIP or SMT package. For enhanced performance, the VRE310 has an external trim option for users who want less than 0.01% initial error. For ultra low noise applications, an external capacitor can be attached between the noise reduction pin and the ground pin. A reference ground pin is provided to eliminate socket contact resistance errors. Figure 1. BLOCK DIAGRAM Selection Guide Model Initial Error Temp. Coeff. (mV) (ppm/ºC) VRE310AS VRE310AD VRE310BS VRE310BD VRE310CS VRE310CD VRE310JS VRE310JD VRE310DS 1.0 1.0 1.6 1.6 2.0 2.0 1.0 1.0 http://www.cirrus.com 0.6 0.6 1.0 1.0 2.0 2.0 0.6 0.6 Temp. Range (ºC) Package Options 0ºC to +70ºC 0ºC to +70ºC 0ºC to +70ºC 0ºC to +70ºC 0ºC to +70ºC 0ºC to +70ºC -40ºC to +85ºC -40ºC to +85ºC SMT8 (GD) DIP8 (KD) SMT8 (GD) DIP8 (KD) SMT8 (GD) DIP8 (KD) SMT8 (GD) DIP8 (KD) Copyright © Cirrus Logic, Inc. 2009 (All Rights Reserved) 8-pin Surface Mount 8-pin DIP Package Style GD Package Style KD MAR 2009 APEX − VRE310DSREVE VRE310 P r o d u c t I n n o v a t i o nF r o m 1. Characteristics and Specifications ELECTRICAL Specifications Vps =±15V, T = +25ºC, RL = 10KΩ Unless Otherwise Noted. Model A/J Parameter Min B C Typ Max Min Typ Max Min Typ Max Units ±15 ±22 * * * * * * V +70 * * * * ºC ABSOLUTE MAXIMUM RATINGS Power Supply ±13.5 Operating Temperature (A,B,C) 0 Operating Temperature (J) -40 +85 * * * * ºC Storage Temperature -65 +150 * * * * ºC Short Circuit Protection Continuous * * +10.0 * * V 630 * * mV OUTPUT VOLTAGE VRE310 Temp. Sensor Voltage (Note 1) OUTPUT VOLTAGE ERRORS Initial Error (Note 2) ±1.0 Warmup Drift ±1.6 1 TMIN - TMAX (Note3) (Note 4) mV 2.0 ppm/ºC 3 0.6 Long-Term Stability Noise (0.1 - 10Hz) 2 ±2.0 ppm 1.0 6 * * ppm/1000hrs. 6 * * µVpp OUTPUT CURRENT Range ±10 * mA REGULATION Line 6 10 * * * * ppm/V Load 3 * * ppm/mA 20 * * mV OUTPUT ADJUSTMENT Range POWER SUPPLY CURRENT (Note 5) VRE310 +PS 5 7 * * * * mA NOTES: * Same as A/J Models. 1. The temp. reference TC is 2.1 mV/ ºC 2. The specified values are without external trim. 3. The temperature coefficient is determined by the box method using the following formula: VMAX – VMIN T.C. = x 106 VNOMINAL x (TMAX – TMIN) 4. The specified values are without the external noise reduction capacitor. 5. The specified values are unloaded. VRE310DS VRE310 P r o d u c t I n n o v a t i o nF r o m 2. TYPICAL PERFORMANCE CURVES VOUT vs. TEMPERATURE VOUT vs. TEMPERATURE Temperature oC VRE310A Temperature oC VRE310B VOUT vs. TEMPERATURE VOUT vs. TEMPERATURE Temperature oC VRE310C QUIESCENT CURRENT VS. TEMP JUNCTION TEMP. RISE VS. OUTPUT CURRENT Temperature oC VRE310DS Temperature oC VRE310J Output Current (mA) PSRR VS. FREQUENCY Frequency (Hz) VRE310 P r o d u c t I n n o v a t i o nF r o m 3. THEORY OF OPERATION The following discussion refers to the block diagram in Figure 1. In operation, approximately 6.3 V is applied to the noninverting input of the op amp. The voltage is amplified by the op amp to produce a 10 V output. The gain is determined by the networks R1 and R2: G=1 + R2/R1. The 6.3 V zener diode is used because it is the most stable diode over time and temperature. The zener operating current is derived from the regulated output voltage through R3. This feedback arrangement provides a closely regulated zener current. This current determines the slope of the references’ voltage vs. temperature function. By trimming the zener current a lower drift over temperature can be achieved. But since the voltage vs. temperature function is nonlinear this compensation technique is not well suited for wide temperature ranges. A nonlinear compensation network of thermistors and resistors is used in the VRE series voltage references. This proprietary network eliminates most of the nonlinearity in the voltage vs. temperature function. By then adjusting the slope, a very stable voltage is produced over wide temperature ranges. This network is less than 2% of the overall network resistance so it has a negligible effect on long term stability. By using highly stable resistors in our network, we produce a voltage reference that also has very good long term stability. The proper connection of the VRE310 series voltage references with the optional trim resistor is shown below. The VRE310 reference has the ground terminal brought out on two pins (pin 4 and pin 7) which are connected together internally. This allows the user to achieve greater accuracy when using a socket. Voltage references have a voltage drop across their power supply ground pin due to quiescent current flowing through the contact resistance. If the contact resistance was constant with time and temperature, this voltage drop could be trimmed out. When the reference is plugged into a socket, this source of error can be as high as 20 ppm. By connecting pin 4 to the power supply ground and pin 7 to a high impedance ground point in the measurement circuit, the error due to the contact resistance can be eliminated. If the unit is soldered into place, the contact resistance is sufficiently small that it does not effect performance. Pay careful attention to the circuit layout to avoid noise pickup and voltage drops in the lines. EXTERNAL CONNECTIONS + VIN V TEMP OUT 2 OPTIONAL NOISE REDUCTION CAPACITOR CN 1µF 3 8 + VOUT 6 VRE310 10kΩ 5 OPTIONAL FINE TRIM ADJUSTMENT 4 7 REF. GND PIN CONFIGURATION N/C 1 +VIN 2 TEMP 3 GND 4 VRE310 TOP VIEW 8 NOISE REDUCTION 7 REF. GND 6 VOUT 5 TRIM VRE310DS VRE310 P r o d u c t I n n o v a t i o nF r o m Contacting Cirrus Logic Support For all Apex Precision Power product questions and inquiries, call toll free 800-546-2739 in North America. For inquiries via email, please contact [email protected]. International customers can also request support by contacting their local Cirrus Logic Sales Representative. To find the one nearest to you, go to www.cirrus.com IMPORTANT NOTICE Cirrus Logic, Inc. and its subsidiaries ("Cirrus") believe that the information contained in this document is accurate and reliable. However, the information is subject to change without notice and is provided "AS IS" without warranty of any kind (express or implied). Customers are advised to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, indemnification, and limitation of liability. No responsibility is assumed by Cirrus for the use of this information, including use of this information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third parties. This document is the property of Cirrus and by furnishing this information, Cirrus grants no license, express or implied under any patents, mask work rights, copyrights, trademarks, trade secrets or other intellectual property rights. Cirrus owns the copyrights associated with the information contained herein and gives consent for copies to be made of the information only for use within your organization with respect to Cirrus integrated circuits or other products of Cirrus. This consent does not extend to other copying such as copying for general distribution, advertising or promotional purposes, or for creating any work for resale. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). CIRRUS PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED TO BE SUITABLE FOR USE IN PRODUCTS SURGICALLY IMPLANTED INTO THE BODY, AUTOMOTIVE SAFETY OR SECURITY DEVICES, LIFE SUPPORT PRODUCTS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF CIRRUS PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK AND CIRRUS DISCLAIMS AND MAKES NO WARRANTY, EXPRESS, STATUTORY OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, WITH REGARD TO ANY CIRRUS PRODUCT THAT IS USED IN SUCH A MANNER. IF THE CUSTOMER OR CUSTOMER’S CUSTOMER USES OR PERMITS THE USE OF CIRRUS PRODUCTS IN CRITICAL APPLICATIONS, CUSTOMER AGREES, BY SUCH USE, TO FULLY INDEMNIFY CIRRUS, ITS OFFICERS, DIRECTORS, EMPLOYEES, DISTRIBUTORS AND OTHER AGENTS FROM ANY AND ALL LIABILITY, INCLUDING ATTORNEYS’ FEES AND COSTS, THAT MAY RESULT FROM OR ARISE IN CONNECTION WITH THESE USES. Cirrus Logic, Cirrus, and the Cirrus Logic logo designs, Apex Precision Power, Apex and the Apex Precision Power logo designs are trademarks of Cirrus Logic, Inc. All other brand and product names in this document may be trademarks or service marks of their respective owners. VRE310DS