50W Solid State BUCs CPI Solid Inside and Out Ku- Band Model B3UO Global Applications With CPI-built RF brick inside and plenty of thermal margin, this SSPA is rock-solid, highly efficient and easy to maintain. Excellent AM/PM, phase noise and spectral regrowth performance. Perfect for Satcom on the Move, Micro Flyaway Systems, VSATs, and antennamount applications. Meets International Safety Standard EN-60950, Electromagnetic Compatibility 89/336/EEC and Harmonic Standard EN-61000-3-2 to satisfy worldwide requirements. Simple to Operate Worldwide Support User-friendly microprocessor-controlled logic with both integrated serial (RS-232 and RS-422/485) and Ethernet computer interfaces. Also contains digitally controlled attenuator. Backed by over three decades of satellite communications experience, and CPI’s worldwide 24-hour customer support network that includes sixteen regional factory service centers. High LInearity Extended Band Operation Provides 45 watts of P1dB output power at the flange over the entire 13.75 to 14.50 GHz frequency range. 811 Hansen Way P.O. Box 51625, Palo Alto, CA 94303 tel: +1 (650) 846-3803 fax: +1 (650) 424-1744 e-mail: [email protected] www.cpii.com/satcom 50W Solid State BUCs CPI-Built RF Brick Inside Ku-Band 50 watt Ku-band Solid State Block Upconverters — Environmentally sealed compact design for outdoor operation Ku -B a n d SPECIFICATIONS, 50 W Ku-Band Outdoor Solid State BUC (Model B3UO) Monitor and Control Electrical OPTIONS: Frequency 13.75 to 14.50 GHz L-Band Input 950 to 1700 MHz • 14.0 - 14.5 GHz operation Output Power 50W (47.0 dBm) Psat 45W (46.5 dBm) P1dB • Front Panel Display Local Oscillator Frequency 12,800 MHz or 13,050 MHz (select either) Internal 10 MHz Reference standard Small Signal Gain 70 dB min. (higher gain options available) Gain Stability Over temp., constant drive Over 24 hours, fixed temp. ±1.0 dB over oper. temp. range ±0.25 dB Gain Slope ±0.04 dB/MHz max. Small Signal Gain Variation Across any 80 MHz band Across the full band ±0.85 dB pk-pk max. ±1.25 dB Gain Adjustment Range Input VSWR Output VSWR 1.3:1 max. Load VSWR Continuous operation Full spec compliance 2.0:1 1.5:1 Residual AM, max. -80 dBc > 100 kHz from carrier Phase Noise, max. 100 Hz 1 kHz 10 kHz 100 kHz 1 MHz -63 dBc/Hz -73 dBc/Hz -83 dBc/Hz -93 dBc/Hz -103 dBc/Hz Remote Status Transmit ON/OFF, Summary Fault Temperature, Fault Identification RF Inhibit (ON/OFF), Lock Detect Environmental Relative Humidity 100% condensing Altitude 12,000 ft. with standard adiabatic derating of 2°C/1000 ft., operating; 50,000 ft., non-operating 17 dB Cooling Integral forced air 1.5:1 max. (50 ohms) Shock and Vibration 20 g peak, 11 msec, 2 sine; 2.1 grms, 5 to 500 Hz. Mechanical AM/PM Conversion 2.5°/dB max. for a single-carrier at 2.5 dB backoff from P1dB Harmonic Output -60 dBc max. at P1dB Spurious Response at P1dB -60 dBc max. in band Intermodulation Distortion -25 dBc max. with two equal carriers and 5 MHz apart at 3.0 dB total backoff from P1dB Group Delay (in any 80 MHz band) 0.03 ns/MHz linear max. 0.003 ns/MHz2 parabolic max. 1.0 ns pk-pk ripple max. Primary Power Single phase, 100-250 VAC ±10% 47-63 Hz Power Consumption 428 VA typ. Power Factor 0.95 min. Note: Specifications may change without notice as a result of additional data or product refinement. Please contact CPI before using this information for system design. PDF Computer/Network Interface RS-232C, 422/485 and Ethernet -40°C to +60°C operating, solar loading immune; -50°C to +85°C non-operating For more detailed information, please refer to the corresponding CPI Technical Description. 2/09 Transmit ON/OFF Fault Reset Attenuator Setting Ambient Temperature Certificate Number: 30515 MKT 193, ISSUE 17 Remote Control RF Output Connection WR-75 waveguide flange, grooved with UNC 2B 6-32 threaded holes L-Band Input connection Type N female M&C Connection 12 Pin Circular (LF10WBR-12S) Dimensions 6 x 6 x 16 in. (142 x 142 x 406 mm) Weight 25 lbs (11.4 kg) typ.