CPI 2.25 kW SuperLinear tm TWT Amplifier for Satellite Communications C - Band The TL22CI 2.25 kW (1000 W operating) TWT Compact High Power Amplifier, features high efficiency, small size and integral computer interface. Meets International Safety Standard EN-60215 and EMC Standard 2004/108/EC to satisfy worldwide requirements. Efficient and Reliable Employs an ultra-high efficiency dual-depressed collector helix traveling wave tube backed by many years of field-proven experience in airborne and military applications. The collector design is optimized for super-cool operation. Easy to Maintain Modular design and built-in fault diagnostic capability with convenient and clearly visible indicators for easy maintainability in the field. Worldwide Support Backed by over two decades of satellite communications experience, and CPI’s worldwide 24-hour customer support network that includes sixteen regional factory Service Centers. Simple to Operate User-friendly microprocessor-controlled logic with integrated computer interface, digital metering, pin diode attenuation, optional integrated linearizer for improved intermodulation performance, and BUC option for use with C-band modems. 811 Hansen Way P.O. Box 51625, Palo Alto, CA 94303 tel: +1 (650) 846-3803 fax: +1 (650) 424-1744 e-mail: [email protected] www.cpii.com/satcom 2 . 2 5 k W S u p e r L i n e a r tm C o m p a c t T W TA Global Applications Provides 2250 watts of peak power (1000 watts operating) in a compact nine rack-unit package, digital ready, for wideband, single- and multicarrier satellite service in the 5.85 - 6.65 GHz frequency band. Designed to operate at 1000 watts flange linear power for multi-carrier uplinks. Ideal for transportable and fixed earth station applications where space and prime power are at a premium. 30% smaller than traditional HPAs. C-Band Compact C-B a n d SPECIFICATIONS, TL22CI Electrical Electrical (continued) Frequency 5.85 - 6.65 GHz Output Power TWT Flange 2250 W min. (63.54 dBm) 1000 W max operating. (60.00 dBm) Bandwidth 800 MHz (1225 MHz optional) Gain 75 dB min. at rated power output 78 dB min. at small signal RF Level Adjust 0 to 30 dB continuous • Integral Linearizer Output Power Adjustability ±0.1 dB • Remote Control Panel Gain Stability • Redundant and Power Combined Subsystems ±0.25 dB/24 hr max. (at constant drive and temp.) Small Signal Gain Slope 0.02 dB/MHz max. Small Signal Gain Variation 0.5 dB pk-pk max. over any 40 MHz; 1.0 dB pk-pk max. over any 40MHz with linearizer option; 3.0 dB pk-pk max. across 800 MHz; 4.0 dB pk-pk max. across 800 MHz with linearizer option; 5.0 dB pk-pk max. across 800 MHz with BUC option; 6.0 dB pk-pk max. across 800 MHz with BUC and linearizer options OPTIONS & C O M PA N I O N PRODUCTS: • Extended Frequency (5.850 - 6.725 GHz or 5.725 - 6.525 GHz) • External Receive Band Reject Filter • Integral L-Band Block Upconverter (BUC) Input/Output VSWR 1.25:1 max. Load VSWR 2.0:1 max. for full spec compliance; any value without damage Residual AM, max.1 -50 dBc below 10 kHz, -20 (1.5 + log F kHz) dBc, 10 kHz to 500 kHz (F in kHz) -85 dBc above 500 kHz Phase Noise1 IESS-308/309 phase noise continuous AC fundamentals related Sum of spurs 10 dB below mask at -10 dB backof -50 dBc -47 dBc All ratings are ±10%, 47-63 Hz, 5-wire, 3-phase with neutral and ground 200 to 240 VAC (with or w/o neutral) 380 to 415 VAC Power Factor 0.95 min. Power Consumption 5.0 kW max.; 4.5 kW typ. @ 1000 W linear RF output power; 3.8 kW typ. @ 800 W; 3.5 kW typ. @ 600 W; 3.3 kW typ. @ 400 W; 2.9 kW typ. @ 200 W; 2.5 kW typ. @ 100 W Environmental Ambient Temperature -10° to +50°C operating -20° to +70°C non-operating Relative Humidity 95% non-condensing Altitude Up to 10,000 ft (3000 m) with standard adiabatic derating of 2°/1000 ft.; 50,000 feet non-operating Shock and Vibration Designed for normal transportation environment per Section 514.4 MIL-STD-810E. Designed to withstand 20g at 11 ms (1/2 sine pulse) in non-operating condition Mechanical Cooling(TWT) Forced air with integral blower and power supply fan. Maximum external pressure loss allowable: 0.25 inch water gauge. RF Input Connection Type N female RF Output Connection CPR 137 F waveguide flange, grooved, threaded UNF 2B 10-32 Harmonic Output -80 dBc RF Power Monitors Type N female Noise and Spurious -150 dBW/4 kHz from 3.4 to 4.2 GHz -65 dBW/4 kHz from 4.2 to 12.0 GHz -60 dBW/4 kHz from 4.2 to 12.0 GHz with linearizer option -110 dBW/4 kHz from 12.0 to 40.0 GHz Dimensions (W x H x D) 19 x 15.75 x 24 in. (483 x 400 x 610 mm) Weight 155 lbs. (70.5 kg) max. -23.5 dBc max, 5.850 - 6.425 GHz at 400 W without linearizer (-25 dBc max. at 890 W with linearizer); -22 dBc max. 6.425 - 6.650 GHz at 400 W without linearizer (-24 dBc max. at 890 W with linearizer) For more detailed information, please refer to the corresponding CPI Technical Description. Note: Specifications may change without notice as a result of additional data or product refinement. Please contact CPI before using this information for system design. PDF Primary Power2 6°/dB max. With optional linearizer, can be tuned to 2°/dB max. Certificate Number: 30515 02/08 0.01 ns/MHz linear 0.001 ns/MHz2 parabolic 0.5 ns pk-pk ripple max. AM/PM Conversion Intermodulation with two equal carriers MKT 160, ISSUE 9 Group Delay (in any 40 MHz band) 1Prime power AC line unbalance not to exceed 3%. Excess imbalance may cause an increase in residual RF noise (AM, FM and PM). Phase noise increase is typically 2.5 dB / % imbalance. 2AC current harmonic content: less than 20%, primarily fifth and seventh harmonics. Harmonics must be considered when choosing UPS sources.