EPCOS B82477P2154M000

SMT power inductors
Size 12.5 x 12.5 x 6 (mm)
Series/Type:
Ordering code:
B82477P2
Date:
Version:
May 2009
02
Content of header bars 1 and 2 of data sheet will be automatically entered in headers and footers! Please fill in the
table and then change the color to "white". This ensures that the table disappears (invisible) for the customer PDF.
Don't change formatting when entering or pasting text in the table and don't add any cell or line in and to it!
Identification/Classification 1
(header 1 + top left bar):
SMT power inductors
Identification/Classification 2
(header 2 + bottom left header bar):
Size 12.5 x 12.5 x 6 (mm)
Ordering code: (top right header bar)
B82477P2
Series/Type: (top right header bar)
Preliminary data (optional):
(if necessary)
Department:
IN TCF PMD A
Date:
May 2009
Version:
02
 EPCOS AG 2009. Reproduction, publication and dissemination of this publication, enclosures hereto and the information
contained therein without EPCOS' prior express consent is prohibited
SMT power inductors
Size 12.5 x 12.5 x 6 (mm)
B82477P2
Rated inductance 1 - 1000 µH
Rated current 0.53 .. 9.25 A
Construction
■ Ferrite core
■ Magnetically shielded
■ Winding: enamel copper wire
■ Winding soldered to terminals
■ Injection molded base
Features
■ High mechanical stability
■ Temperature range up to 150 °C
■ High rated current
■ Low DC resistance
■ Suitable for lead-free reflow soldering
as referenced in JEDEC J-STD 020C
■ Qualification to AEC-Q200
■ RoHS-compatible
Applications
■ Filtering of supply voltages
■ Coupling, decoupling
■ DC/DC converters
■ Automotive electronics
Terminals
■ Base material
Cu (L ≤ 10µH) CuSn6P (L ≥ 15µH)
■ Layer composition Ni, Sn (lead-free)
■ Electro-plated
Marking
■ Marking on component:
Manufacturer, L value (µH, coded),
manufacturing date (YWWD)
■ Minimum data on reel:
Manufacturer, ordering code, L value,
quantity, date of packing
Delivery mode and packing unit
■ 24-mm blister tape, wound on 330-mm reel
■ Packing unit: 600 pcs./reel
IN TCF PMD A
Please read Cautions and warnings and
Important notes at the end of this document.
May 2009
Page 2 of 8
SMT power inductors
Size 12.5 x 12.5 x 6 (mm)
B82477P2
Dimensional drawing and layout recommendation
Dimensions in mm
Taping and packing
Blister tape and reel
Dimensions in mm
IN TCF PMD A
Please read Cautions and warnings and
Important notes at the end of this document.
May 2009
Page 3 of 8
SMT power inductors
Size 12.5 x 12.5 x 6 (mm)
B82477P2
Technical data and measuring conditions
Rated inductance LR
Measured with LCR meter Agilent 4284A at frequency fL,
0.1 V, 20 °C
Rated temperature TR
85 °C
Rated current IR
Saturation current ISat
Max. permissible DC with temperature increase of ≤40 K
at rated temperature
Max. permissible DC with inductance decrease ∆L/L0 of
approx. 10%,
DC resistance Rtyp
Measured at 20 °C
Solderability (lead-free)
Dip and look method Sn95.5Ag3.8Cu0.7:
(245 5) °C, (3 0.3) s
Wetting of soldering area 90%
(based on IEC 60068-2-58)
Resistance to soldering heat
260 °C, 40 s (as referenced in JEDEC J-STD 020C)
Climatic category
55/150/56 (to IEC 60068-1)
Storage conditions
Mounted: –55 °C … +150 °C
Packaged: –25 °C … +40 °C, ≤75% RH
Weight
Approx. 3 g
IN TCF PMD A
Please read Cautions and warnings and
Important notes at the end of this document.
May 2009
Page 4 of 8
SMT power inductors
Size 12.5 x 12.5 x 6 (mm)
B82477P2
Characteristics and ordering codes
LR
µH
1.0
1.5
2.2
3.3
4.7
6.8
10
15
22
33
47
68
100
150
220
330
470
680
1000
Tolerance
20% = M
fL
MHz
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
IR
A
9.25
8.70
7.20
6.70
5.40
4.80
4.30
3.70
3.40
2.70
2.40
1.85
1.65
1.35
1.15
0.95
0.80
0.62
0.53
Isat
A
10.0
8.70
8.00
7.20
5.70
4.80
4.00
3.30
2.80
2.20
1.90
1.50
1.30
1.00
0.80
0.68
0.58
0.48
0.40
IN TCF PMD A
Please read Cautions and warnings and
Important notes at the end of this document.
Rmax
Ω
0,008
0,010
0,012
0,014
0,016
0,020
0,025
0,030
0,036
0,055
0,070
0,110
0,140
0,210
0,300
0,460
0,550
1,050
1,300
Ordering code
B82477P2102M000
B82477P2152M000
B82477P2222M000
B82477P2332M000
B82477P2472M000
B82477P2682M000
B82477P2103M000
B82477P2153M000
B82477P2223M000
B82477P2333M000
B82477P2473M000
B82477P2683M000
B82477P2104M000
B82477P2154M000
B82477P2224M000
B82477P2334M000
B82477P2474M000
B82477P2684M000
B82477P2105M000
May 2009
Page 5 of 8
SMT power inductors
Size 12.5 x 12.5 x 6 (mm)
B82477P2
Impedance versus frequency (typical curve)
1000000.0
Z/Ohm
10000.0
100.0
1000µH
100µH
10µH
1.0
1µH
0.0
0.0
0.1
1.0
10.0
Inductance derating
versus load current (typical curve)
100.0
Current derating Iop/IR
versus ambient temperature TA
(rated temperature TR = 85 °C)
IN TCF PMD A
Please read Cautions and warnings and
Important notes at the end of this document.
f/MHz
May 2009
Page 6 of 8
SMT power inductors
Size 12.5 x 12.5 x 6 (mm)
B82477P2
Cautions and warnings
■ Please note the recommendations in our Inductors data book (latest edition) and in the data
sheets.
– Particular attention should be paid to the derating curves given there.
– The soldering conditions should also be observed. Temperatures quoted in relation to wave
soldering refer to the pin, not the housing.
■ If the components are to be washed varnished it is necessary to check whether the washing
varnish agent that is used has a negative effect on the wire insulation, any plastics that are used,
or on glued joints. In particular, it is possible for washing varnish agent residues to have a
negative effect in the long-term on wire insulation.
■ The following points must be observed if the components are potted in customer applications:
– Many potting materials shrink as they harden. They therefore exert a pressure on the plastic
housing or core. This pressure can have a deleterious effect on electrical properties, and in
extreme cases can damage the core or plastic housing mechanically.
– It is necessary to check whether the potting material used attacks or destroys the wire
insulation, plastics or glue.
– The effect of the potting material can change the high-frequecy behaviour of the components.
■ Ferrites are sensitive to direct impact. This can cause the core material to flake, or lead to
breakage of the core.
■ Even for customer-specific products, conclusive validation of the component in the circuit can
only be carried out by the customer.
IN TCF PMD A
Please read Cautions and warnings and
Important notes at the end of this document.
May 2009
Page 7 of 8
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical
requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application. As a
rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them
than the customers themselves. For these reasons, it is always ultimately incumbent on the
customer to check and decide whether an EPCOS product with the properties described in the
product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or failure
before the end of their usual service life cannot be completely ruled out in the current state
of the art, even if they are operated as specified. In customer applications requiring a very high
level of operational safety and especially in customer applications in which the malfunction or
failure of an electronic component could endanger human life or health (e.g. in accident
prevention or life-saving systems), it must therefore be ensured by means of suitable design of the
customer application or other action taken by the customer (e.g. installation of protective circuitry
or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or
failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our Material
Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed
questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order.
We also reserve the right to discontinue production and delivery of products. Consequently,
we cannot guarantee that all products named in this publication will always be available.
The aforementioned does not apply in the case of individual agreements deviating from the
foregoing for customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of
the “General Terms of Delivery for Products and Services in the Electrical Industry”
published by the German Electrical and Electronics Industry Association (ZVEI).
7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSMP, CSSP, CTVS, DSSP, MiniBlue,
MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, SIFERRIT, SIFI, SIKOREL,
SilverCap, SIMDAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are
trademarks registered or pending in Europe and in other countries. Further information will be
found on the Internet at www.epcos.com/trademarks.
Page 8 of 8