Switching spark gap SSG for SMD handling Series/Type: Ordering code: CAS02XSMD B88069X6321T602 Version/Date: Version: Issue 02 / 2006-10-30 04 Content of header bars 1 and 2 of data sheet will be automatically entered in headers and footers! Please fill in the table and then change the color to "white" (or invisible). This ensures that the table disappears for the customer PDF. To update the data sheet, click on the symbol "Preview" and then "Close". Please do not alter the header or footer when copying the content. Identification/Classification 1: (header 1 + top left header bar) Switching spark gap Identification/Classification 2: (header 2 + bottom left header bar) SSG for SMD handling Ordering code: (top right header bar) B88069X6321T602 Series/Type: (top right header bar) CAS02XSMD Preliminary data (optional): (if necessary) Department: KB AB E / KB AB PM Date: Issue 02 / 2006-10-30 © EPCOS AG 2006. Reproduction, publication and dissemination of this document, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. Switching spark gap SSG for SMD handling B88069X6321T602 CAS02XSMD Features Applications Long life time Stable performance over life Insensitive performance against variations in temperature Low switching losses Very short breakdown time High reliability by robust design SMD handling RoHS-compatible Ignition for gas stoves Electrical specifications DC spark-over voltage 1) 2) 215 ... 255 V Initial values Ignition time tI after 150 hours in darkness 3) 95 ≤4 ≤2 at –20 °C at +25; 150 °C Electrical life time A Maximum increase of DC spark-over voltage Switching operations at +25; 125 °C Switching frequency 10 … 25 Hz Switching frequency < 10 Hz Test circuit parameters; 1 s ON, 10 s OFF Open circuit voltage V0' Loading resistance R Discharge capacitance C Inductance L Discharge peak current IP 99.9 ≤5 ≤3 100 ≤7 ≤4 % s s 25 V 2 000 000 4 000 000 Ignitions Ignitions 230 15 2.2 10 ~ 300 Vac kΩ µF µH A 600 000 Ignitions 230 1.5 0.1 7 ~ 300 Vac kΩ µF µH A Insulation resistance at 100 Vdc > 0.1 GΩ Capacitance at 1 MHz <2 pF Weight ~ 1.5 g Electrical life time B Switching operations at +25 °C Switching frequency 1000 Hz Test circuit parameters; 1 cycle 10 min ON Open circuit voltage V0' Loading resistance R Discharge capacitance C Inductance L Discharge peak current IP KB AB E / KB AB PM Please read Cautions and warnings and Important notes at the end of this document. Issue 02 / 2006-10-30 Page 2 of 5 Switching spark gap SSG for SMD handling B88069X6321T602 CAS02XSMD Operation and storage temperature -20 ... +150 Climatic category (IEC 60068-1) 20/ 150/ 21 Marking, red positive CS 230 YYMM O CS 230 YY MM O 1) 2) 3) °C - Series - Nominal voltage - Year of production - Month of production - Non radioactive At delivery AQL 0.65 level II, DIN ISO 2859 In ionized mode, after load Time from capacitor charged to the first high voltage spark Test circuit: Vac = 198 V; R = 36 kΩ; C = 2.2 µF Dimensional drawing Not to scale Dimensions in mm Non controlled document KB AB E / KB AB PM Please read Cautions and warnings and Important notes at the end of this document. Issue 02 / 2006-10-30 Page 3 of 5 Switching spark gap SSG for SMD handling B88069X6321T602 CAS02XSMD Packing advice T602 = SMD-tape with 600 pcs Cautions and warnings Switching spark gaps may be used only within their specified values. Damaged switching spark gaps must not be re-used. KB AB E / KB AB PM Please read Cautions and warnings and Important notes at the end of this document. Issue 02 / 2006-10-30 Page 4 of 5 Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of passive electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of a passive electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of a passive electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as “hazardous”). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms of Delivery for Products and Services in the Electrical Industry” published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, EPCOS-JONES, Alu-X, Baoke, CeraDiode, CSSP, MLSC, PhaseCap, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMID, SIOV, SIP5D, SIP5K, UltraCap, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks. Page 5 of 5