bq2204A X4 SRAM Nonvolatile Controller Unit General Description Features ä Power monitoring and switching for 3-volt battery-backup applications ä Write-protect control ä 2-input decoder for control of up to 4 banks of SRAM ä 3-volt primary cell inputs ä Les s t han 10ns chip- e nable propagation delay ä 5% or 10% supply operation The CMOS bq2204A SRAM Nonvolatile Controller Unit provides all necessary functions for converting up to four banks of standard CMOS SRAM into nonvolatile read/write memory. A precision comparator monitors the 5V VCC input for an out-of-tolerance condition. When out-of-tolerance is detected, the four conditioned chip-enable outputs are forced inactive to write-protect up to four banks of SRAM. Pin Connections During a power failure, the external SRAMs are switched from the VCC supply to one of two 3V backup supplies. On a subsequent power-up, the SRAMs are write-protected until a power-valid condition exists. During power-valid operation, a two-input decoder transparently selects one of up to four banks of SRAM. Pin Names VOUT Supply output BC1–BC2 3 volt primary backup cell inputs THS Threshold select input VOUT 1 16 VCC BC2 2 15 BC1 NC 3 14 CE CE chip-enable active low input A 4 13 CECON1 5 12 CECON2 CECON1– CECON4 Conditioned chip-enable outputs B NC 6 11 CECON3 A–B Decoder inputs THS 7 10 CECON4 NC No connect VSS 8 9 VCC +5 volt supply input VSS Ground NC 16-Pin Narrow DIP or SOIC PN220401.eps Functional Description If THS is tied to VCC, power-fail detection occurs at 4.37V typical for 10% supply operation. The THS pin must be tied to VSS or VCC for proper operation. Up to four banks of CMOS static RAM can be batterybacked using the VOUT and conditioned chip-enable output pins from the bq2204A. As VCC slews down during a power failure, the conditioned chip-enable outputs CECON1 through CECON4 are forced inactive independent of the chip-enable input CE. If a memory access is in process to any of the four external banks of SRAM during power-fail detection, that memory cycle continues to completion before the memory is writeprotected. If the memory cycle is not terminated within time tWPT, all four chip-enable outputs are unconditionally driven high, write-protecting the controlled SRAMs. This activity unconditionally write-protects the external SRAM as VCC falls below an out-of-tolerance threshold VPFD. VPFD is selected by the threshold select input pin, THS. If THS is tied to VSS, the power-fail detection occurs at 4.62V typical for 5% supply operation. Dec. 1992 B 1 bq2204A During power-valid operation, the CE input is passed through to one of the four CECON outputs with a propagation delay of less than 10ns. The CE input is output on one of the four CECON output pins depending on the level of the decode inputs at A and B as shown in the Truth Table. As the supply continues to fall past VPFD, an internal switching device forces VOUT to one of the two external backup energy sources. CECON1 through CECON4 are held high by the VOUT energy source. During power-up, VOUT is switched back to the 5V supply as VCC rises above the backup cell input voltage sourcing VOUT. Outputs CECON1 through CECON4 are held inactive for time tCER (120ms maximum) after the power supply has reached VPFD, independent of the CE input, to allow for processor stabilization. The A and B inputs are usually tied to high-order address pins so that a large nonvolatile memory can be designed using lower-density memory devices. Nonvolatility and decoding are achieved by hardware hookup as shown in Figure 1. 5V VCC VOUT bq2204A A B From Address Decoder 3V Primary Cell CECON1 CE CECON2 BC2 CECON3 THS CECON4 VSS BC1 VCC VCC VCC VCC CMOS SRAM CMOS SRAM CMOS SRAM CMOS SRAM CE CE CE CE 3V Primary Cell FG220401.eps Figure 1. Hardware Hookup (5% Supply Operation) Dec. 1992 B 2 bq2204A Energy Cell Inputs—BC1, BC2 Two backup energy source inputs are provided on the bq2204A. The BC1 and BC2 inputs accept a 3V primary battery (non-rechargeable), typically some type of lithium chemistry. If no primary cell is to be used on either BC1 or BC2, the unused input should be tied to VSS. VPFD VCC falling below VPFD starts the comparison of BC1 and BC2. The BC input comparison continues until VCC rises above VSO. Power to VOUT begins with BC1 and switches to BC2 only when VBC1 is less than VBC2 minus VBSO. The controller alternates to the higher BC voltage only when the difference between the BC input voltages is greater than VBSO. Alternating the backup batteries allows one-at-a-time battery replacement and efficient use of both backup batteries. VCC VSO 0.5 VCC CE 700ns To prevent battery drain when there is no valid data to retain, VOUT and CECON1-4 are internally isolated from BC1 and BC2 by either of the following conditions: ■ Initial connection of a battery to BC1 or BC2, or ■ Presentation of an isolation signal on CE. TD220201.eps A valid isolation signal requires CE low as VCC crosses both VPFD and VSO during a power-down. See Figure 2. Between these two points in time, CE must be brought to the point of (0.48 to 0.52)*VCC and held for at least 700ns. The isolation signal is invalid if CE exceeds 0.54*VCC at any point between VCC crossing VPFD and VSO. Figure 2. Battery Isolation Signal The appropriate battery is connected to V OUT and CECON1–4 immediately on subsequent application and removal of VCC. Truth Table Input Output CE A B CECON1 CECON2 CECON3 CECON4 H X X H H H H L L L L H H H L H L H L H H L L H H H L H L H H H H H L Dec. 1992 B 3 bq2204A Absolute Maximum Ratings Symbol Parameter Value Unit Conditions VCC DC voltage applied on VCC relative to VSS -0.3 to +7.0 V VT DC voltage applied on any pin excluding VCC relative to VSS -0.3 to +7.0 V VT ≤ VCC + 0.3 0 to 70 °C Commercial TOPR Operating temperature -40 to +85 °C Industrial “N” TSTG Storage temperature -55 to +125 °C TBIAS Temperature under bias -40 to +85 °C TSOLDER Soldering temperature 260 °C IOUT VOUT current 200 mA Note: For 10 seconds Permanent device damage may occur if Absolute Maximum Ratings are exceeded. Functional operation should be limited to the Recommended DC Operating Conditions detailed in this data sheet. Exposure to conditions beyond the operational limits for extended periods of time may affect device reliability. Recommended DC Operating Conditions (TA = TOPR) Symbol Parameter Minimum Typical Maximum Unit 4.75 5.0 5.5 V THS = VSS 4.50 5.0 5.5 V THS = VCC 0 0 0 V VCC Supply voltage VSS Supply voltage VIL Input low voltage -0.3 - 0.8 V VIH Input high voltage 2.2 - VCC + 0.3 V VBC1, VBC2 Backup cell voltage 2.0 - 4.0 V THS Threshold select -0.3 - VCC + 0.3 V Note: Notes VCC < VBC Typical values indicate operation at TA = 25°C, VCC = 5V or VBC. Dec. 1992 B 4 bq2204A DC Electrical Characteristics (TA = TOPR, VCC = 5V ± 10%) Symbol Parameter Minimum Typical Maximum Unit Conditions/Notes - - ±1 µA 2.4 - - V IOH = -2.0mA VBC - 0.3 - - V VBC > VCC, IOH = -10µA IOL = 4.0mA ILI Input leakage current VOH Output high voltage VOHB VOH, BC supply VOL Output low voltage - - 0.4 V ICC Operating supply current - 3 6 mA 4.55 4.62 4.75 V THS = VSS VPFD Power-fail detect voltage 4.30 4.37 4.50 V THS = VCC VSO Supply switch-over voltage - VBC - V ICCDR Data-retention mode current - - 100 nA Active backup cell voltage - VBC1 - V VBC1 > VBC2 + VBSO VBC - VBC2 - V VBC2 > VBC1 + VBSO VBSO Battery switch-over voltage 0.25 0.4 0.6 V IOUT1 VOUT current - - 160 mA VOUT > VCC - 0.3V IOUT2 VOUT current - 100 - µA VOUT > VBC - 0.2V Note: VIN = VSS to VCC No load on outputs. VOUT data-retention current to additional memory not included. Typical values indicate operation at TA = 25°C, VCC = 5V or VBC. Capacitance (TA = 25°C, F = 1MHz, VCC = 5.0V) Symbol Parameter Minimum Typical Maximum Unit Conditions CIN Input capacitance - - 8 pF Input voltage = 0V COUT Output capacitance - - 10 pF Output voltage = 0V Note: This parameter is sampled and not 100% tested. Dec. 1992 B 5 bq2204A AC Test Conditions Parameter Test Conditions Input pulse levels 0V to 3.0V Input rise and fall times 5ns Input and output timing reference levels 1.5V (unless otherwise specified) 5V 960 CECON 100pF 510 FG220102.eps Figure 3. Output Load Power-Fail Control (TA = TOPR) Symbol Parameter Minimum Typical Maximum Unit tPF VCC slew, 4.75V to 4.25V 300 - - µs tFS VCC slew, 4.25V to VSO 10 - - µs Notes tPU VCC slew, 4.25V to 4.75V 0 - - µs tCED chip-enable propagation delay - 7 10 ns tAS A,B set up to CE 0 - - ns tCER chip-enable recovery 40 80 120 ms Time during which SRAM is write-protected after VCC passes VPFD on power-up. tWPT Write-protect time 40 100 150 µs Delay after VCC slews down past VPFD before SRAM is write-protected. Note: Typical values indicate operation at TA = 25°C, VCC = 5V. Caution: Negative undershoots below the absolute maximum rating of -0.3V in battery-backup mode may affect data integrity. Dec. 1992 B 6 bq2204A Power-Down Timing tPF 4.75 VPFD VCC tFS 4.25 VSO CE tWPT VOHB CECON TD220102.eps Power-Up Timing tPU VCC 4.75 VPFD 4.25 VSO tCER CE CECON tCED VOHB tCED TD220103.eps Address-Decode Timing A,B tAS CE tCED CECON1 tCED CECON4 TD220402.eps Dec. 1992 B 7 bq2204A Data Sheet Revision History Change No. Page No. 1 All 1 1, 4–5 10% tolerance requires the THS pin to be tied to VCC, not VOUT. 1 3 Energy cell input selection process alternates between BC1 and BC2. Note: Description of Change Nature of Change bq2204A replaces bq2204. Change 1 = Dec. 1992 changes from Sept. 1991 Dec. 1992 B 10 PACKAGE OPTION ADDENDUM www.ti.com 3-Dec-2011 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) BQ2204APN ACTIVE PDIP N 16 25 Pb-Free (RoHS) BQ2204ASN ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR BQ2204ASN-N ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR BQ2204ASN-NG4 ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR BQ2204ASNG4 ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR BQ2204ASNTR ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR BQ2204ASNTRG4 ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Samples (Requires Login) CU NIPDAU N / A for Pkg Type (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 3-Dec-2011 continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device BQ2204ASNTR Package Package Pins Type Drawing SOIC D 16 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 2500 330.0 16.4 Pack Materials-Page 1 6.5 B0 (mm) K0 (mm) P1 (mm) 10.3 2.1 8.0 W Pin1 (mm) Quadrant 16.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) BQ2204ASNTR SOIC D 16 2500 367.0 367.0 38.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2012, Texas Instruments Incorporated