Product Specification 8.5 Gb/s Short-Wavelength SFP+ Transceiver FTLF8528P2BNV PRODUCT FEATURES Up to 8.5 Gb/s bi-directional data links Hot-pluggable SFP+ footprint Built-in digital diagnostic functions 850nm Oxide VCSEL laser transmitter Duplex LC connector RoHS compliant and Lead Free 50m on 50/125μm MMF 150m on high-bandwidth 50/125um (OM3) MMF Metal enclosure, for lower EMI Single 3.3V power supply Extended operating temperature range: -5°C to 85°C APPLICATIONS Tri-Rate 2.125/4.25/8.5 Gb/s Fibre Channel Finisar’s FTLF8528P2BNV SFP+ transceivers are designed for use in Fibre Channel links up to 8.5 Gb/s data rate over multimode fiber. They are compliant with FC-PI-4 Rev. 7.001 and SFF-8472 Rev 10.13, and compatible with SFF-84322 and applicable portions of SFF-8431 Rev. 1.34. The product is RoHS compliant and lead-free per Directive 2002/95/EC5 and Finisar Application Note AN-2038. PRODUCT SELECTION FTLF8528P2BNV © Finisar Corporation November 21, 2007 Rev. B Page 1 FTLF8528P2BNV Pluggable SFP+ Product Specification – November 2007 I. Pin Descriptions Pin 1 2 3 4 5 6 7 Symbol VEET TFAULT TDIS SDA SCA MOD_ABS RS0 8 9 LOS RS1 10 11 12 13 14 15 16 17 18 19 20 VEER VEER RDRD+ VEER VCCR VCCT VEET TD+ TDVEET Name/Description Transmitter Ground (Common with Receiver Ground) Transmitter Fault. Transmitter Disable. Laser output disabled on high or open. 2-wire Serial Interface Data Line (MOD-DEF2) 2-wire Serial Interface Clock (MOD-DEF1) Module Absent, connected to VEET or VEER Rx Rate Select: Open or Low = 2.125 or 4.25 Gb/s Fibre Channel (Low Bandwidth) High = 8.5 Gb/s Fibre Channel (High Bandwidth) Loss of Signal indication. Logic 0 indicates normal operation. Tx Rate Select: Open or Low = 2.125 or 4.25 Gb/s Fibre Channel (Low Bandwidth) High = 8.5 Gb/s Fibre Channel (High Bandwidth) Receiver Ground (Common with Transmitter Ground) Receiver Ground (Common with Transmitter Ground) Receiver Inverted DATA out. AC Coupled Receiver Non-inverted DATA out. AC Coupled Receiver Ground (Common with Transmitter Ground) Receiver Power Supply Transmitter Power Supply Transmitter Ground (Common with Receiver Ground) Transmitter Non-Inverted DATA in. AC Coupled. Transmitter Inverted DATA in. AC Coupled. Transmitter Ground (Common with Receiver Ground) Ref. 1 2 3 4 4 4 5 6 5 1 1 1 1 1 Notes: 1. Circuit ground is internally isolated from chassis ground. 2. TFAULT is an open collector/drain output, which should be pulled up with a 4.7k – 10k Ohms resistor on the host board if intended for use. Pull up voltage should be between 2.0V to Vcc + 0.3V. A high output indicates a transmitter fault caused by either the TX bias current or the TX output power exceeding the preset alarm thresholds. A low output indicates normal operation. In the low state, the output is pulled to <0.8V. 3. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V. 4. Should be pulled up with 4.7k – 10kohms on host board to a voltage between 2.0V and 3.6V. MOD_ABS pulls line low to indicate module is plugged in. 5. Rate select can also be set through the 2-wire bus in accordance with SFF-8472 v. 10.13. Rx Rate Select is set at Bit 3, Byte 110, Address A2h. Tx Rate Select is set at Bit 3, Byte 118, Address A2h. Note: writing a “1” selects maximum bandwidth operation. Rate select is the logic OR of the input state of Rate Select Pin and 2-wire bus. 6. LOS is open collector output. Should be pulled up with 4.7k – 10kohms on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal. © Finisar Corporation November 21, 2007 Rev. B Page 2 FTLF8528P2BNV Pluggable SFP+ Product Specification – November 2007 Diagram of Host Board Connector Block Pin Numbers and Names II. Absolute Maximum Ratings Parameter Maximum Supply Voltage Storage Temperature Case Operating Temperature Relative Humidity (Non-condensing) © Finisar Corporation November 21, 2007 Rev. B Symbol Vcc TS TA RH Min -0.5 -40 -5 0 Typ Max 4.0 85 85 85 Unit V °C °C % Ref. Page 3 FTLF8528P2BNV Pluggable SFP+ Product Specification – November 2007 III. Electrical Characteristics (TA = -5 to 85 °C, VCC = 3.0 to 3.6 Volts) Parameter Supply Voltage Supply Current Transmitter Input differential impedance Single ended data input swing Transmit Disable Voltage Transmit Enable Voltage Receiver Single ended data output swing Data Output Rise/Fall Time @ 2.125, 4.25 Gb/s Data Output Rise/Fall Time @ 8.5 Gb/s LOS Fault LOS Normal Power Supply Rejection Deterministic Jitter Contribution @ 2.125 Gb/s Total Jitter Contribution @ 2.125 Gb/s Deterministic Jitter Contribution @ 4.25 Gb/s Total Jitter Contribution @ 4.25 Gb/s Deterministic Jitter @ 8.5 Gb/s Pulse Width Shrinkage @ 8.5 Gb/s Total Jitter @ 8.5 Gb/s Symbol Vcc Icc Rin Vin,pp VD VEN Vout,pp tr/ tf tr/ tf VLOS fault VLOS norm PSR RX Δ DJ RX Δ TJ RX Δ DJ RX Δ TJ RX DJ RX DDPWS RX TJ Min 3.0 Typ Max 3.6 240 Unit V mA Ref. 800 Vcc Vee+ 0.8 Ω mV V V 1 90 2 Vee 170 400 120 60 VccHOST Vee+0.8 3 4 4 5 5 6 47.1 123.5 23.5 61.8 49.4 42.4 mV ps ps V V mVpp ps ps ps ps ps ps 83.5 ps 8 100 2 Vee 100 2 7 8 8 8 Notes: 1. Connected directly to TX data input pins. AC coupling from pins into laser driver IC. 2. Or open circuit. 3. Into 100 ohms differential termination. 4. Unfiltered, 20 – 80 % 5. LOS is an open collector output. Should be pulled up with 4.7k – 10kohms on the host board. Normal operation is logic 0; loss of signal is logic 1. Maximum pull-up voltage is 5.5V. 6. Receiver sensitivity is compliant with power supply sinusoidal modulation of 20 Hz to 1.5 MHz up to specified value applied through the recommended power supply filtering network. 7. If measured with TJ-free data input signal. In actual application, output TJ will be given by: TJ OUT = DJ IN + ΔDJ + 8. (TJ IN − DJ IN )2 + (ΔTJ − ΔDJ )2 As defined in FC-PI-41, Rev 7.0, Table 13, 800-Mx-SN-y. © Finisar Corporation November 21, 2007 Rev. B Page 4 FTLF8528P2BNV Pluggable SFP+ Product Specification – November 2007 IV. Optical Characteristics (TA = -5 to 85 °C, VCC = 3. 0 to 3.6 Volts) Parameter Transmitter Output Opt. Pwr: 50 or 62.5 MMF Optical Wavelength Spectral Width Optical Modulation Amplitude @ 2.125 Gb/s Optical Modulation Amplitude @ 4.25 Gb/s Optical Modulation Amplitude @ 8.5 Gb/s Optical Rise/Fall Time @ 2.125, 4.25 Gb/s Transmitter Waveform and Dispersion Penalty @ 8.5 Gb/s Relative Intensity Noise Deterministic Jitter Contribution @ 2.125 Gb/s Total Jitter Contribution @ 2.125 Gb/s Deterministic Jitter Contribution @ 4.25 Gb/s Total Jitter Contribution @ 4.25 Gb/s Receiver Receiver OMA Sensitivity = 2.125 Gb/s Receiver OMA Sensitivity = 4.25 Gb/s Receiver OMA Sensitivity = 8.5 Gb/s Average Receiver Power Optical Center Wavelength Optical Return Loss LOS De-Assert LOS Assert LOS Hysteresis Symbol Min POUT λ σ OMA OMA OMA tr/ tf TWDP -9 830 Max Unit Ref. -2 860 0.65 1 90 4.2 dBm nm nm μW μW μW ps dB RIN TX Δ DJ TX Δ TJ TX Δ DJ TX Δ TJ -128 56.5 119.6 28.2 59.8 dB/Hz ps ps ps ps RxSENS RxSENS RxSENS RxMAX λC 49 61 76 μW μW μW dBm nm dB dBm dBm dB LOSD LOSA Typ 196 247 302 0 770 12 860 -18 -30 0.5 2 2 2 3 4 5 5 Notes: 1. Class 1 Laser Safety per FDA/CDRH, and EN (IEC) 60825 laser safety standards. 2. Equivalent extinction ratio specification for Fibre Channel. Allows smaller ER at higher average power. 3. Unfiltered, 20-80%. Complies with FC 1x and 2x eye mask when filtered. 4. TWDP is calculated with a 1.0 equalizer and a 6,860 MHz Gaussian filter for the fiber simulation. Jitter values at γT and γR are controlled by TWDP and stress receiver sensitivity. 5. If measured with TJ-free data input signal. In actual application, output TJ will be given by: TJ OUT = DJ IN + ΔDJ + (TJ IN − DJ IN )2 + (ΔTJ − ΔDJ )2 © Finisar Corporation November 21, 2007 Rev. B Page 5 FTLF8528P2BNV Pluggable SFP+ Product Specification – November 2007 V. General Specifications Parameter Data Rate Symbol BR Bit Error Rate Fiber Length on 50/125μm MMF BER L Fiber Length on 50/125μm highbandwidth (OM3) MMF L Min Typ 2.125, 4.25, 8.5 Max 10-12 300 150 50 500 380 150 Units Gb/sec m m Ref. 1 2 3 4 5 3 4 5 Notes: 1. 2x and 4x Fibre Channel compatible, per FC-PI-41. 2. PRBS 27-1. 3. At 2.125 Gb/s Fibre Channel data rate. 4. At 4.25 Gb/s Fibre Channel data rate. 5. At 8.5 Gb/s Fibre Channel data rate. VI. Environmental Specifications Finisar 850nm SFP+ transceivers have an extended operating temperature range from -5°C to +85°C case temperature. Parameter Case Operating Temperature Storage Temperature VII. Symbol Top Tsto Min -5 -40 Typ Max 85 85 Units °C °C Ref. Regulatory Compliance Finisar transceivers are Class 1 Laser Products and comply with US FDA regulations. These products are certified by TÜV and CSA to meet the Class 1 eye safety requirements of EN (IEC) 60825 and the electrical safety requirements of EN (IEC) 60950. Copies of certificates are available at Finisar Corporation upon request. © Finisar Corporation November 21, 2007 Rev. B Page 6 FTLF8528P2BNV Pluggable SFP+ Product Specification – November 2007 VIII. Digital Diagnostic Functions Finisar FTLF8528P2BNV SFP+ transceivers support the 2-wire serial communication protocol as defined in the SFP MSA6. It is very closely related to the E2PROM defined in the GBIC standard, with the same electrical specifications. The standard SFP serial ID provides access to identification information that describes the transceiver’s capabilities, standard interfaces, manufacturer, and other information. Additionally, Finisar SFP transceivers provide a enhanced digital diagnostic monitoring interface, which allows real-time access to device operating parameters such as transceiver temperature, laser bias current, transmitted optical power, received optical power and transceiver supply voltage. It also defines a sophisticated system of alarm and warning flags, which alerts end-users when particular operating parameters are outside of a factory set normal range. The SFP MSA defines a 256-byte memory map in E2PROM that is accessible over a 2-wire serial interface at the 8 bit address 1010000X (A0h). The digital diagnostic monitoring interface makes use of the 8 bit address 1010001X (A2h), so the originally defined serial ID memory map remains unchanged. The interface is identical to, and is thus fully backward compatible with both the GBIC Specification and the SFP Multi Source Agreement. The complete interface is described in Finisar Application Note AN2030: “Digital Diagnostics Monitoring Interface for SFP Optical Transceivers”. The operating and diagnostics information is monitored and reported by a Digital Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed through a 2-wire serial interface. When the serial protocol is activated, the serial clock signal (SCL, Mod Def 1) is generated by the host. The positive edge clocks data into the SFP transceiver into those segments of the E2PROM that are not write-protected. The negative edge clocks data from the SFP transceiver. The serial data signal (SDA, Mod Def 2) is bi-directional for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The memories are organized as a series of 8-bit data words that can be addressed individually or sequentially. For more information, please see the SFP MSA documentation3,6 and Finisar Application Note AN-2030. Please note that evaluation board FDB-1027 is available with Finisar ModDEMO software that allows simple to use communication over the 2-wire serial interface. © Finisar Corporation November 21, 2007 Rev. B Page 7 FTLF8528P2BNV Pluggable SFP+ Product Specification – November 2007 IX. Digital Diagnostic Specifications FTLF8528P2BNV transceivers can be used in host systems that require either internally or externally calibrated digital diagnostics. Parameter Symbol Accuracy DDTemperature Internally measured transceiver temperature DDVoltage Internally measured transceiver supply voltage DDBias Measured TX bias current DDTx-Power Measured TX output power DDRx-Power Measured RX received average optical power Dynamic Range for Rated Accuracy DDTemperature Internally measured transceiver temperature DDVoltage Internally measured transceiver supply voltage DDBias Measured TX bias current DDTx-Power Measured TX output power DDRx-Power Measured RX received average optical power Max Reporting Range DDTemperature Internally measured transceiver temperature DDVoltage Internally measured transceiver supply voltage DDBias Measured TX bias current DDTx-Power Measured TX output power DDRx-Power Measured RX received average optical power Min Typ Max Units 3 ºC 100 mV 10 2 2 % dB dB -5 85 ºC 3.0 3.6 V 0 -9 -18 20 -2 0 mA dBm dBm -40 125 ºC 2.8 4.0 V 0 -10 -20 20 -2 0 mA dBm dBm Ref. 1 Notes: 1. Accuracy of Measured Tx Bias Current is 10% of the actual Bias Current from the laser driver to the laser. © Finisar Corporation November 21, 2007 Rev. B Page 8 FTLF8528P2BNV Pluggable SFP+ Product Specification – November 2007 X. Mechanical Specifications Finisar’s FTLF8528P2BNV SFP+ transceivers are compatible with the SFF-84322 specification for improved pluggable form factor. FTLF8528P2BNV © Finisar Corporation November 21, 2007 Rev. B Page 9 FTLF8528P2BNV Pluggable SFP+ Product Specification – November 2007 XI. PCB Layout and Bezel Recommendations © Finisar Corporation November 21, 2007 Rev. B Page 10 FTLF8528P2BNV Pluggable SFP+ Product Specification – November 2007 © Finisar Corporation November 21, 2007 Rev. B Page 11 FTLF8528P2BNV Pluggable SFP+ Product Specification – November 2007 XII. References 1. “Fibre Channel Physical Interface-4 Specification (FC-PI-4 Rev. 7.00)”. American National Standard for Information Systems, September 20, 2007. 2. “Improved Pluggable Formfactor”, SFF Document Number SFF-8432, Revision 5.0, July 16, 2007. 3. “Digital Monitoring Interface for Optical Transceivers”, SFF Document Number SFF-8472, Revision 10.2, June 1, 2007. 4. “Enhanced Specification for 8.5 and 10 Gigabit Small Form Factor Pluggable Module ‘SFP+ ‘”, SFF Document Number SFF-8431, Revision 2.1, August 30, 2007. 5. Directive 2002/95/EC of the European Council Parliament and of the Council, “on the restriction of the use of certain hazardous substances in electrical and electronic equipment.” January 27, 2003. 6. Small Form Factor Pluggable (SFP) Transceiver Multi-source Agreement (MSA), September 14, 2000. XIII. For More Information Finisar Corporation 1389 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 [email protected] www.finisar.com © Finisar Corporation November 21, 2007 Rev. B Page 12