Product Specification Multi-rate CWDM Pluggable SFP Transceiver FWDM-1621-7D-xx PRODUCT FEATURES • Up to 2.67 Gb/s bi-directional data links • Hot-pluggable SFP footprint • Built-in digital diagnostic functions • Uncooled DFB laser transmitter in 8 possible CWDM wavelengths • APD Receiver • Very low jitter • Metal enclosure, for lower EMI • Single 3.3V power supply • Operating temperature range: 0°C to 70°C APPLICATIONS • Metro Access Rings and Point-toPoint networking for SONET, Gigabit Ethernet and Fibre Channel Finisar’s FWDM-1621-7D-xx CWDM Small Form Factor Pluggable (SFP) transceivers are designed for operation in Metro Access Rings and Point-to-Point networks using SONET1, Gigabit Ethernet2 and Fibre Channel3 networking equipment. They are available in eight different CWDM wavelengths and comply with the ITU CWDM standard4. Digital diagnostics functions are available via an I2C serial bus. In addition, they comply with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA)5. PRODUCT SELECTION Clasp Color Code Wavelength xx 1470 nm 47 Gray 1490 nm 49 Violet 1510 nm 51 Blue 1530 nm 53 Green Finisar Corporation September 2005 Rev. F Wavelength 1550 nm 1570 nm 1590 nm 1610 nm xx 55 57 59 61 Clasp Color Code Yellow Orange Red Brown FWDM-1621-7D-xx SFP Product Specification – September 2005 I. Pin Descriptions Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Symbol VEET TFAULT TDIS MOD_DEF(2) MOD_DEF(1) MOD_DEF(0) Rate Select LOS VEER VEER VEER RDRD+ VEER VCCR VCCT VEET TD+ 19 20 TDVEET Name/Description Transmitter Ground (Common with Receiver Ground) Transmitter Fault. Not supported. Transmitter Disable. Laser output disabled on high or open. Module Definition 2. Data line for Serial ID. Module Definition 1. Clock line for Serial ID. Module Definition 0. Grounded within the module. No connection required Loss of Signal indication. Logic 0 indicates normal operation. Receiver Ground (Common with Transmitter Ground) Receiver Ground (Common with Transmitter Ground) Receiver Ground (Common with Transmitter Ground) Receiver Inverted DATA out. AC Coupled Receiver Non-inverted DATA out. AC Coupled Receiver Ground (Common with Transmitter Ground) Receiver Power Supply Transmitter Power Supply Transmitter Ground (Common with Receiver Ground) Transmitter Non-Inverted DATA in. 100 ohm termination between TD+ and TD-, AC Coupled thereafter. Transmitter Inverted DATA in. See TD+ Transmitter Ground (Common with Receiver Ground) Ref. 1 2 3 3 3 4 5 1 1 1 1 1 1 Notes: 1. Circuit ground is internally isolated from chassis ground. 2. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V. 3. Should be pulled up with 4.7k – 10kohms on host board to a voltage between 2.0V and 5.5V. MOD_DEF(0) pulls line low to indicate module is plugged in. 4. Finisar 2x receiver achieves simultaneous 1x and 2x operation without active control. 5. LOS is open collector output. Should be pulled up with 4.7k – 10kohms on host board to a voltage between 2.0V and 5.5V. Logic 0 indicates normal operation; logic 1 indicates loss of signal. 1 Towards Bezel VeeT 20 TD- 19 TD+ 18 VeeT 17 VccT 16 VccR 15 VeeR 14 RD+ 13 RD- 12 VeeR 11 VeeT 2 TXFault 3 TX Disable 4 MOD-DEF(2) 5 MOD-DEF(1) 6 MOD-DEF(0) 7 Rate Select 8 LOS 9 VeeR 10 VeeR Towards ASIC Diagram of Host Board Connector Block Pin Numbers and Names Finisar Corporation September 2005 Rev. F Page 2 FWDM-1621-7D-xx SFP Product Specification – September 2005 II. Absolute Maximum Ratings Parameter Maximum Supply Voltage Storage Temperature Case Operating Temperature III. Symbol Vcc TS TOP Min -0.5 -40 0 Typ Max 4.7 85 70 Unit V °C °C Ref. Max 3.60 300 Unit V mA Ref. Ω mV V V us 1 1200 Vcc Vee+ 0.8 10 Electrical Characteristics (TOP = 0 to 70 °C, VCC = 3.15 to 3.60 Volts) Parameter Supply Voltage Supply Current Transmitter Input differential impedance Single ended data input swing Transmit Disable Voltage Transmit Enable Voltage Transmit Disable Assert Time Receiver Single ended data output swing Data output rise time Data output fall time LOS Fault LOS Normal Power Supply Rejection Symbol Vcc Icc Rin Vin,pp VD VEN Vout,pp tr tf VLOS fault VLOS norm PSR Min 3.15 Typ 210 100 250 Vcc – 1.3 Vee 250 100 100 Vcc – 0.5 Vee 100 800 180 180 VccHOST Vee+0.5 mV ps ps V V mVpp 2 3 4 4 5 5 6 Notes: 1. Connected directly to TX data input pins. AC coupled thereafter. 2. Or open circuit. 3. Into 100 ohms differential termination. 4. 20 – 80 % 5. Loss Of Signal is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected. 6. Receiver sensitivity is compliant with power supply sinusoidal modulation of 20 Hz to 1.5 MHz up to specified value applied through the recommended power supply filtering network. Finisar Corporation September 2005 Rev. F Page 3 FWDM-1621-7D-xx SFP Product Specification – September 2005 IV. Low Speed Signals Parameter RX_LOS Assert Level RX_LOS Deassert Level RX_LOS Hysteresis RX_LOS Assert Delay t_loss_on 100 RX_LOS Negate Delay t_loss_off 100 TX_DISABLE Assert Time t_off 10 TX_DISABLE Negate Time t_on 1000 TX_DISABLE Reset Time Symbol Min -41 Typ 0.5 2 Max -30 t_reset 10 TX_FAULT Assert 100 Initialization Time 300 Finisar Corporation September 2005 Rev. F Units Notes/Conditions dBm dBm dB µsec From detection of loss of signal to assertion of RX_LOS µsec From detection of presence of signal to negation of RX_LOS µsec Rising edge of TX_DISABLE to fall of output signal below 10% of nominal µsec Falling edge of TX_DISABLE to rise of output signal above 90% of nominal. Time indicated is under steady-state temperature conditions. µsec TX_DISABLE HIGH before TX_DISABLE set LOW µsec From fault to assertion of TX_FAULT µsec From power on to negation of TX_FAULT using TX_DISABLE Page 4 FWDM-1621-7D-xx SFP Product Specification – September 2005 V. Optical Characteristics (TOP = 0 to 70 °C, VCC = 3.15 to 3.60 Volts) Parameter Transmitter Output Opt. Pwr (EOL) Optical Wavelength Wavelength Temperature Dependence Spectral Width Optical Extinction Ratio Sidemode Suppression ratio Optical Rise/Fall Time RIN Transmitter Jitter Generation Dispersion Penalty at 80 km Receiver Optical Input Power Optical Input Wavelength Receiver Jitter Generation Optical Return Loss Symbol Min POUT λ 0 (X-6.5) ∆λ20 ER SMSRmin tr/ tf RIN 8.2 30 Pin λC Typ Max Unit (X+1) 0.08 +5 (X+6.5) 0.125 1 dBm nm nm/°C nm dB dB ps dB/Hz mUI dB 180 -120 75 2.5 -28 1450 27 -9 1620 75 dBm nm mUI dB Ref. 2 3 4 5 6 7 8 9 7 Notes: 1. Parameters are specified over temperature and voltage, at end of life unless otherwise noted. 2. Class 1 Laser Safety per FDA/CDRH and IEC-825-1 regulations. 3. Over case temperature of 0 to 70 °C. The Transmitter Center Wavelength “X” is as specified by the customer. The current available wavelengths are: 1470, 1490, 1510, 1530, 1550, 1570, 1590, and 1610 nm. Please see the “Product Selection” section on page 1. 4. Full width, -20dB from peak. 5. Measured filtered, at 2.488 Gb/s. Min represents worst-case ER over temperature and at end of life. 6. Unfiltered, 20% to 80%. 7. Measured per GR-2532 section 5.6 for OC-48 B. 8. SMF-28 fiber used. 80kms represents 1600ps/nm at 1610nm. Measured at 2.488Gb/s with a PRBS 223-1 pattern at a BER<10-12. 9. Pin represents the range of input powers where BER<10-12. Pin is valid over all data rates specified in Section IV. Finisar Corporation September 2005 Rev. F Page 5 FWDM-1621-7D-xx SFP Product Specification – September 2005 VI. General Specifications Parameter Data Rate Symbol BR Min 0.155* Typ Total Link Budget -- 28 30 VII. Max 2.67 Units Ref. Gb/sec *OC-3/12 compatible. Not compliant w/ all OC-3/12 specifications, such as min ER. (OC-48 compliance takes precedence) dB 2.488 Gb/s, BER < 10-12 w/ PRBS 223-1. Does not include dispersion penalty Environmental Specifications Parameter Case Operating Temperature Storage Temperature Symbol Top Tsto Min 0 -40 Typ Max 70 85 Units °C °C Ref. VIII. Regulatory Compliance Finisar CWDM SFP transceivers are Class 1 Laser Products. They are certified per the following standards: Feature Laser Eye Safety Agency FDA/CDRH Laser Eye Safety TÜV Electrical Safety CSA Standard CDRH and IEC-825 Class 1 Laser Product. See Note 1 EN 60950 EN 60825-1 EN 60825-2 CLASS 3862.07 CLASS 3862.87 Note 1: Complies with FDA performance standards for laser products except for deviations pursuant to Laser Notice No. 50, dated July 26, 2001. Finisar Corporation September 2005 Rev. F Page 6 FWDM-1621-7D-xx SFP Product Specification – September 2005 IX. Digital Diagnostic Functions All Finisar SFPs support the 2-wire serial communication protocol outlined in the SFP MSA5. These SFPs use an Atmel AT24C01A 128 byte E2PROM with an address of A0h (see table below for E2PROM contents). For details on interfacing with the E2PROM, see the Atmel data sheet titled “AT24C01A/02/04/08/16 2-Wire Serial CMOS E2PROM.”6 Finisar’s CWDM SFPs also support extended diagnostic features as described in Finisar Applications Note AN-2030, “Digital Diagnostic Monitoring Interface for Optical Transceivers”7, and additional information is available in SFF standard titled: “Digital Diagnostic Monitoring Interface for Optical Transceivers8 (SFF-8472 rev9.3). A controller IC that monitors system parameters such as laser current, module temperature, transmitter power, and received power is accessible at address A2H. I2C clock speed, digital diagnostic accuracy and digital diagnostic range can be found in the table below. Values in the table represent the worst-case values over temperature, voltage, and life. Parameter I2C Clock Speed Accuracy Internal Transceiver Temperature Internal Transceiver Supply Voltage Tx Bias Curent Tx Output Power Received Average Power Range Internal Transceiver Temperature Internal Transceiver Supply Voltage Tx Bias Curent Tx Output Power Received Average Power Symbol Min Typ Max Units Notes/Conditions 0 100,000 Hz Bus can be driven blind DDTemperature -3 +3 °C Measured at controller IC DDVoltage -3 +3 % Measured at controller IC DDBias DDTxPower -10 -3 +10 +3 % dB DDRxPower -3 +3 dB DDTemperature -40 85 °C DDVoltage 3.0 4.0 V DDBias DDTxPower DDRxPower 0 -10 -30 90 5 -7 mA dBm dBm Finisar Corporation September 2005 Rev. F 100% tested in production tested at room temp to ±2 dB 100% tested in production tested at room temp to ±2 dB Page 7 FWDM-1621-7D-xx SFP Product Specification – September 2005 X. Mechanical Specifications Finisar’s Multi-rate CWDM Small Form Factor Pluggable (SFP) transceivers are compatible with the dimensions defined by the SFP Multi-Sourcing Agreement (MSA). * FWDM-1621-7D-xx Outline Drawing - units in inches [mm] Finisar Corporation September 2005 Rev. F Page 8 FWDM-1621-7D-xx SFP Product Specification – September 2005 XI. PCB Layout and Bezel Recommendations Finisar Corporation September 2005 Rev. F Page 9 FWDM-1621-7D-xx SFP Product Specification – September 2005 Finisar Corporation September 2005 Rev. F Page 10 FWDM-1621-7D-xx SFP Product Specification – September 2005 XII. References 1. “SONET Transport Systems: Common Generic Criteria”, Telcordia Technologies, GR-253-CORE, Issue 3, September 2000. 2. IEEE Std 802.3. IEEE Standards Department, 2000.(*) 3. “Fibre Channel Draft Physical Interface Specification (FC-PI 10.0)”. American National Standard for Information Systems.(*) 4. “Optical Interfaces for Course Wavelength Division Multiplexing Applications”, ITU-T Reccomendation G.695, January 2005 5. Small Form Factor Pluggable (SFP) Transceiver Multi-Source Agreement (MSA), September 2000. Documentation is currently available at Finisar upon request. 6. “AT24C01A/02/04/08/16 2-Wire Serial CMOS E2PROM”, Atmel Corporation. www.Atmel.com 7. “Application Note AN-2030: Digital Diagnostic Monitoring Interface for Optical Transceivers”, Finisar Corporation, April 2002. 8. “Digital Diagnostic Monitoring Interface For Optical Transceivers Rev 9.3”. SFF Document No. SFF-8472. (*) Neither IEEE 802.3 nor FC-PI 10.0 specifies a 1621 nm DFB single mode interface. The FWDM-16217Dxx complies with these specifications except for the following optical parameters, which have different values: transmitter wavelength, extinction ratio, receiver sensitivity, and transmit output power. See Section V for details. For More Information Finisar Corporation 1308 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 [email protected] www.finisar.com Finisar Corporation September 2005 Rev. F Page 11