DUAL 150MA HIGH PERFORMANCE MOBILE LDOTM IN SOT23-6L FSP2150 FEATURES z z z z z z z z 180mV Typical Dropout with 150mA Load ±2.0% Voltage Accuracy High PSRR: 70dB@100Hz Low noise output Current Limit Thermal Shutdown Protection Short Circuit Protection Very small SOT23-6L Package APPLICATIONS z z z z z z Cellular Handsets Portable Electronics, PDA Wireless Devices, LAN Computer Peripherals Camera Module GPS Receiver The dual LDO FSP2150 series of positive voltage linear regulators feature high output voltage accuracy, low quiescent current and low dropout voltage, making them ideal for battery powered applications. The line transient response and load transient response are excellent. Their high PSRR make them useful in applications where AC noise on the input power supply must be suppressed. Space-saving SOT23-6L package for 2ch LDOs is attractive for portable and handheld applications. They have both thermal shutdown and a current limit feature to prevent device failure under extreme operating conditions. They are stable with an output capacitance of 2.2uF or greater. PIN CONFIGURATION GENERAL DESCRIPTION (Top View) 1/9 OUT1 GND OUT2 6 5 4 1 2 3 EN1 IN EN2 PIN DESCRIPTION Pin Number Pin Name 1 2 3 4 5 6 EN1 VIN EN2 OUT2 GND OUT1 Pin Function Output 1 Enable Input Output 2 Enable Output 2 Ground Output 1 2007-6-28 DUAL 150MA HIGH PERFORMANCE MOBILE LDOTM IN SOT23-6L FSP2150 ABSOLUTE MAXIMUM RATINGS Parameter Input Voltage Output Pin Voltage Rating 6 Unit V GND-0.3 to VIN + 0.3 V Output Current 150/150 mA Internal Power Dissipation 400 mW ESD Rating(HBM) 2000 V Operating Junction Temperature -40 to 125 °C Operating Ambient Temperature -40 to 85 °C Storage Temperature -40 to 125 °C Lead Temperature (Soldering, 5 sec) 300 Note: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired °C ELECTRICAL CHARACTERISTICS (VIN = VOUT + 1V, EN1 =EN2= IN, CIN = 2.2F, COUT = 2.2F, TA= 25°C unless otherwise specified.) Parameter Test Conditions Min Typ Max Unit Input Supply Range Note 1 5.5 V EN Input Voltage 0 VIN V -2.0 +2.0 % Output Voltage Accuracy IO=1mA Note 2 mA Quiescent Current Output Current IO=0mA 175 250 µA Shutdown Supply Current Short Circuit Current Both outputs disabled 0.1 1 µA VO= 0V 150 Ground Pin Current IO=1mA to 150mA 200 250 µA -0.15 0.1 0.15 %/V -2 1.0 2 %/mA Line Regulation Load Regulation Power Supply Ripple Rejection 150 IO=50mA VIN = 3.0V to 4.0V VO= 1.8V IO=50mA VIN = 3.5V to 4.5V VO= 2.5 IO=50mA VIN = 3.8V to 4.8V VO= 2.8V IOUT = 1mA to 150mA VIN= 3.3V IO=50mA VO = 1.8V f= 100Hz 70 f= 1KHz 63 f= 10KHz mA dB 45 VOUT = 1.8V, IOUT = 150mA 950 VOUT = 2.5V, IOUT = 150mA 350 VOUT = 2.8V, IOUT = 150mA 180 Current Limit VOUT ≥1.2V 200 mA Dropout Voltage mV Output Noise f= 10Hz to 100KHz 35 uVrms Over Temperature Hystersis IO=1mA 40 °C Over Temperature Shutdown IO=1mA 155 °C EN_ Logic Low Threshold 0.3 EN_ Logic High Threshold 1.5 EN Pull-up Resistance 1.7 V V 5 15 mΩ Temperature Coefficient 40 ppm/°C Note 1：The minimum input voltage of the FSP2150 is determined by output voltage and dropout voltage. The minimum input voltage is defined as: VIN(MIN)=VO+VDROP Note 2：Output current is limited by PD, maximum IO=PD/(VIN(MAX)-VO) 2/9 2007-6-28 DUAL 150MA HIGH PERFORMANCE MOBILE LDOTM IN SOT23-6L FSP2150 FUNCTIONAL BLOCK DIAGRAM TYPICAL APPLICATION CIRCUIT APPLICATION INFORMATION Capacitor Selection and Regulator Stability Similar to any low dropout regulator, the external capacitors used with the FSP2150 must be carefully selected for regulator stability and performance. Using a capacitor, CIN, whose value is＞2.2μF at the FSP2150 input pin, the amount of the capacitance can be increased without limit. Please note that the distance between CIN and the input pin of the FSP2150 should not exceed 0.5 inch. Ceramic capacitors are suitable for the FSP2150. Capacitors with larger values and lower ESR provide better PSRR and line-transient response. The FSP2150 is designed specifically to work with low ESR ceramic output capacitors in order to save space and improve performance. Using an output ceramic capacitor whose value is ＞2.2μF with ESR＞5mΩ ensure stability. Shutdown Input Operation The FSP2150 is shutdown by pulling the EN input low, and is turned on by tying the EN input to VIN or leaving the EN input floating. Dropout Voltage A regulator’s minimum dropout voltage determines the lowest usable supply voltage. The FSP2150 has a typical 180mV dropout voltage. In battery powered systems, this will determine the useful end-of-life battery voltage. Current Limit and Short Circuit Protection The FSP2150 features a current limit, which monitors and controls the gate voltage of the pass transistor. The output current can be limited to 300mA by regulating the gate voltage. The FSP2150 also has a built-in short circuit current limit. 3/9 2007-6-28 DUAL 150MA HIGH PERFORMANCE MOBILE LDOTM IN SOT23-6L FSP2150 TYPICAL PERFORMANCE CHARACTERISTICS (CIN = 2.2uF, CO = 2.2uF, TA = 25°C unless otherwise specified.) 4/9 2007-6-28 DUAL 150MA HIGH PERFORMANCE MOBILE LDOTM IN SOT23-6L FSP2150 TYPICAL PERFORMANCE CHARACTERISTICS（CONTINUED） (CIN = 2.2uF, CO = 2.2uF, TA = 25°C unless otherwise specified.) 5/9 2007-6-28 DUAL 150MA HIGH PERFORMANCE MOBILE LDOTM IN SOT23-6L FSP2150 TYPICAL PERFORMANCE CHARACTERISTICS（CONTINUED） (CIN = 2.2uF, CO = 2.2uF, TA = 25°C unless otherwise specified.) 6/9 2007-6-28 DUAL 150MA HIGH PERFORMANCE MOBILE LDOTM IN SOT23-6L FSP2150 TYPICAL PERFORMANCE CHARACTERISTICS（CONTINUED） (CIN = 2.2uF, CO = 2.2uF, TA = 25°C unless otherwise specified.) 7/9 2007-6-28 DUAL 150MA HIGH PERFORMANCE MOBILE LDOTM IN SOT23-6L FSP2150 TYPICAL PERFORMANCE CHARACTERISTICS（CONTINUED） (CIN = 2.2uF, CO = 2.2uF, TA = 25°C unless otherwise specified.) Turn-on Response ORDERING INFORMATION FSP2150XXXX Package: C: SOT23-6L Output Voltage: (Out 1, Out 2) A: 1.8V, 2.8V B: 1.8V, 2.5V Packing: A: Tape & Reel Temperature Grade: D: -40~85℃ MARKING INFORMATION XXVYW Date code: Y: Year W: Week Output Voltage: A: 1.8V, 2.8V B: 1.8V, 2.5V Product Code 8/9 2007-6-28 DUAL 150MA HIGH PERFORMANCE MOBILE LDOTM IN SOT23-6L FSP2150 PACKAGE INFORMATION D e 2 3 A1 1 A 4 E 5 E1 6 A2 e1 b C θ L Symbol A A1 A2 b C D E E1 L L1 e1 e θ 9/9 Dimensions In Millimeters Min. Max. 1.050 1.250 0.000 0.100 1.050 1.150 0.300 0.400 0.100 0.200 2.820 3.020 2.650 2.950 1.500 1.700 0.300 0.600 0.700REF 0.95 Bsc. 1.90 Bsc. 0º 8º Dimensions In Inches Min. Max. 0.041 0.049 0.000 0.004 0.041 0.045 0.012 0.016 0.004 0.008 0.111 0.119 0.104 0.116 0.060 0.068 0.012 0.024 0.028REF 0.038 Bsc. 0.076 Bsc. 0º 8º 2007-6-28