HYNIX H55S5162DFR-A3M

512MBit MOBILE SDR SDRAMs based on 8M x 4Bank x16I/O
Specification of
512Mb (32Mx16bit) Mobile SDRAM
Memory Cell Array
- Organized as 4banks of 8,388,608 x16
This document is a general product description and is subject to change without notice. Hynix does not assume any responsibility for
use of circuits described. No patent licenses are implied.
Rev 1.5 / Feb. 2009
1
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
Document Title
4Bank x 8M x 16bits Synchronous DRAM
Revision History
Revision No.
History
Draft Date
Remark
0.1
Initial Draft
Sep. 2007
Preliminary
0.2
Update: IDD values
Mar. 2008
Preliminary
1.0
Final Version
Apr. 2008
1.1
-.
-.
-.
-.
May 2008
1.2
Modify : tRAS (166MHz/133Mhz: 42ns/45ns)
Jun. 2008
1.3
Modify : tCK (CL=2, 166MHz [12ns -> 9.6ns])
Jun. 2008
1.4
Change the ball height(page 54)
Jan. 2009
1.5
Add : AC Undershoot/Overshoot specification
Feb. 2009
Rev 1.5 / Feb. 2009
Corrected the description of BURST TERMINATE
Corrected the CKE state on every command
Corrected PKG size (8mm x 10mm to 8mm x 8mm)
Deleted the extended temperature products
2
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
DESCRIPTION
The Hynix H55S5162DFR is suited for non-PC application which use the batteries such as PDAs, 2.5G and 3G cellular
phones with internet access and multimedia capabilities, mini-notebook, hand-held PCs.
The Hynix 512M Mobile SDRAM is 536,870,912-bit CMOS Mobile Synchronous DRAM(Mobile SDR), ideally suited for the
main memory applications which requires large memory density and high bandwidth. It is organized as 4banks of
8,388,608x16.
Mobile SDRAM is a type of DRAM which operates in synchronization with input clock. The Hynix Mobile SDRAM latch
each control signal at the rising edge of a basic input clock (CLK) and input/output data in synchronization with the
input clock (CLK). The address lines are multiplexed with the Data Input/ Output signals on a multiplexed x16 Input/
Output bus. All the commands are latched in synchronization with the rising edge of CLK.
The Mobile SDRAMs provides for programmable read or write Burst length of Programmable burst lengths: 1, 2, 4, 8
locations or full page. An AUTO PRECHARGE function may be enabled to provide a self-timed row precharge that is initiated at the end of the burst access. The Mobile SDRAM uses an internal pipelined architecture to achieve high-speed
operation. This architecture is compatible with the 2n rule of prefetch architectures, but it also allows the column
address to be changed on every clock cycle to achieve a high-speed, fully random access. Precharging one bank while
accessing one of the other three banks will hide the precharge cycles and provide seamless, high-speed, randomaccess operation.
Read and write accesses to the Hynix Mobile SDRAMs are burst oriented;
accesses start at a selected location and continue for a programmed number of locations in a programmed sequence.
Accesses begin with the registration of an ACTIVE command, which is then followed by a READ or WRITE command.
The address bits registered coincident with the ACTIVE command are used to select the bank and the row to be
accessed. The address bits registered coincident with the READ or WRITE command are used to select the bank and
the starting column location for the burst access. A burst of Read or Write cycles in progress can be terminated by a
burst terminate command or can be interrupted and replaced by a new burst Read or Write command on any
cycle(This pipelined design is not restricted by a 2N rule).
The Hynix Mobile SDR also provides for special programmable options including Partial Array Self Refresh of full array,
half array, quarter array Temperature Compensated Self Refresh of 45 or 85 degrees oC.
The Hynix Mobile SDR has the special Low Power function of Auto TCSR(Temperature Compensated Self Refresh) to
reduce self refresh current consumption. Since an internal temperature sensor is implanted, it enables to automatically
adjust refresh rate according to temperature without external EMRS command.
Deep Power Down Mode is a additional operating mode for Mobile SDR. This mode can achieve maximum power
reduction by removing power to the memory array within each Mobile SDR. By using this feature, the system can cut
off almost all DRAM power without adding the cost of a power switch and giving up mother-board power-line layout
flexibility.
All inputs are LV-CMOS compatible. Devices will have a VDD and VDDQ supply of 1.8V (nominal).
Rev 1.5 / Feb. 2009
3
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
INFORMATION for Hynix KNOWN GOOD DIE
With the advent of Multi-Chip package (MCPs), Package on Package (PoP) and system in a package (SiP) applications,
customer demand for Known Good Die (KGD) has increased.
Requirements for smaller form factors and higher memory densities are fueling the need for Wafer-level memory solutions due to their superior flexibility. Hynix Known Good Die (KGD) products can be used in packaging technologies
such as systems-in-a-package (SIPs) and multi-chip packages (MCPs) to reduce the board area required, making them
ideal for hand-held PCs, and many other portable digital applications.
Hynix Mobile DRAM will be able to continue its constant effort of enabling the Advanced package products of all application customers.
- Please Contact Hynix Office for Hynix KGD product availability and informations.
Rev 1.5 / Feb. 2009
4
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
FEATURES
●
●
Standard SDRAM Protocol
Clock Synchronization Operation
- All the commands registered on positive edge of basic input clock (CLK)
●
MULTIBANK OPERATION - Internal 4bank operation
- During burst Read or Write operation, burst Read or Write for a different bank is performed.
- During burst Read or Write operation, a different bank is activated and burst Read or Write
for that bank is performed
- During auto precharge burst Read or Write, burst Read or Write for a different bank is performed
●
●
●
●
●
●
●
●
Power Supply Voltage: VDD = 1.8V, VDDQ = 1.8V
LVCMOS compatible I/O Interface
Low Voltage interface to reduce I/O power
Programmable burst length: 1, 2, 4, 8 or full page
Programmable Burst Type: sequential or interleaved
Programmable CAS latency of 3 or 2
Programmable Drive Strength
Low Power Features
- Programmable PASR(Partial Array Self Refresh)
- Auto TCSR (Temperature Compensated Self Refresh)
- Programmable DS (Drive Strength)
- Deep Power Down Mode
●
Operation Temperature
- Mobile Temp.: -30oC ~ 85oC
●
Package Type: 54ball FBGA, 0.8mm pitch, 8 x 8 [mm2], t=1.0mm max, Lead & Halogen Free
512M SDRAM ORDERING INFORMATION
Part Number
Clock
Frequency
H55S5162DFR-60M
166MHz
H55S5162DFR-75M
133MHz
H55S5162DFR-A3M
105MHz
Rev 1.5 / Feb. 2009
Temperature
CAS
Latency
Organization
Interface
54Ball
FBGA
Mobile Temp.
-30oC ~ 85oC
3
4banks x 8Mb x 16
LVCMOS
Lead &
Halogen
Free
5
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
BALL DESCRIPTION
8
9
3
7
2
1
A
B
C
54 Ball
D
FBGA
E
0.8mm
Ball Pitch
F
G
H
J
<Bottom View>
1
2
3
7
8
9
VSS
DQ15
VSSQ
A
VDDQ
DQ0
VDD
DQ14
DQ13
VDDQ
B
VSSQ
DQ2
DQ1
DQ12
DQ11
VSSQ
C
VDDQ
DQ4
DQ3
DQ10
DQ9
VDDQ
D
VSSQ
DQ6
DQ5
DQ8
NC
VSS
E
VDD
LDQM
DQ7
UDQM
CLK
CKE
F
/ CAS
/ RAS
/ WE
A12
A11
A9
G
BA0
BA1
/ CS
A8
A7
A6
H
A0
A1
A10
VSS
A5
A4
J
A3
A2
VDD
< Top View >
Rev 1.5 / Feb. 2009
6
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
BALL DESCRIPTION
SYMBOL
TYPE
CLK
INPUT
CKE
INPUT
CS
INPUT
BA0, BA1
INPUT
A0 ~ A12
INPUT
RAS, CAS, WE
INPUT
UDQM, LDQM
INPUT
DQ0 ~ DQ15
I/O
VDD/VSS
SUPPLY
Power supply for internal circuits
VDDQ/VSSQ
SUPPLY
Power supply for output buffers
NC
-
Rev 1.5 / Feb. 2009
DESCRIPTION
Clock: The system clock input. All other inputs are registered to the SDRAM on the
rising edge of CLK
Clock Enable: Controls internal clock signal and when deactivated, the SDRAM will
be one of the states among (deep) power down, suspend or self refresh
Chip Select: Enables or disables all inputs except CLK, CKE, UDQM and LDQM
Bank Address: Selects bank to be activated during RAS activity
Selects bank to be read/written during CAS activity
Row Address: RA0 ~ RA12, Column Address: CA0 ~ CA9
Auto-precharge flag: A10
Command Inputs: RAS, CAS and WE define the operation
Refer function truth table for details
Data Mask: Controls output buffers in read mode and masks input data in write
mode
Data Input/Output: Multiplexed data input/output pin
No connection
7
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
ABSOLUTE MAXIMUM RATING
Parameter
Symbol
Rating
Ambient Temperature
TA
-30 ~ 85
o
C
Storage Temperature
TSTG
-55 ~ 125
o
C
VIN, VOUT
-1.0 ~ 2.6
V
VDD
-1.0 ~ 2.6
V
VDDQ
-1.0 ~ 2.6
V
Short Circuit Output Current
IOS
50
mA
Power Dissipation
PD
1
W
TSOLDER
260 . 20
Voltage on Any Pin relative to VSS
Voltage on VDD relative to VSS
Voltage on VDDQ relative to VSS
Soldering Temperature . Time
Unit
oC . Sec
DC OPERATING CONDITION (TA= -30 to 85oC)
Parameter
Symbol
Min
Typ
Max
Unit
Note
Power Supply Voltage
VDD
1.7
1.8
1.95
V
1
Power Supply Voltage
VDDQ
1.7
1.8
1.95
V
1, 2
Input High Voltage
VIH
0.8*VDDQ
-
VDDQ+0.3
V
1, 2
Input Low Voltage
VIL
-0.3
-
0.3
V
1, 2
Notes:
1. All Voltages are referenced to VSS = 0V
2. VDDQ must not exceed the level of VDD
AC OPERATING TEST CONDITION (TA= -30 to 85 oC, VDD = 1.8V, VSS = 0V)
Parameter
Symbol
Value
Unit
VIH / VIL
0.9*VDDQ/0.2
V
Vtrip
0.5*VDDQ
V
Input Rise/Fall Time
tR / tF
1
ns
Output Timing Measurement Reference Level Voltage
Voutref
0.5*VDDQ
V
CL
30
pF
AC Input High/Low Level Voltage
Input Timing Measurement Reference Level Voltage
Output Load Capacitance for Access Time Measurement
Rev 1.5 / Feb. 2009
8
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
CAPACITANCE (TA= 25 oC, f=1MHz)
6/H/S
Parameter
Pin
Symbol
CLK
Input capacitance
A0~A12, BA0, BA1, CKE, CS, RAS,
CAS, WE, UDQM, LDQM
Data input/output capacitance
DQ0 ~ DQ15
Unit
Min
Max
CI1
2
4.0
pF
CI2
2
4.0
pF
CI/O
2
4.5
pF
DC CHARACTERRISTICS I (TA= -30 to 85oC)
Parameter
Symbol
Min
Max
Unit
Note
Input Leakage Current
ILI
-1
1
uA
1
Output Leakage Current
ILO
-1
1
uA
2
Output High Voltage
VOH
VDDQ-0.2
-
V
3
Output Low Voltage
VOL
-
0.2
V
4
Notes:
1. VIN = 0 to 1.8V. All other pins are not tested under VIN=0V.
2. DOUT is disabled. VOUT= 0 to 1.95V.
3. IOUT = - 0.1mA
4. IOUT = + 0.1mA
Rev 1.5 / Feb. 2009
9
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
Mobile SDRAM AC OVERSHOOT / UNDERSHOOT SPECIFICATION
Parameter
Maximum peak amplitude allowed for overshoot
Maximum peak amplitude allowed for undershoot
The area between overshoot signal and VDD must be less than or equal to
The area between undershoot signal and GND must be less than or equal to
Specification
0.5V
0.5V
3V-ns
3V-ns
Note:
1. This specification is intended for devices with no clamp protection and is guaranteed by design.
2.5V
Overshoot
2.0V
Voltage (V)
VDD
1.5V
1.0V
Max. Amplitude = 0.5V
Max. Area = 3V-ns
0.5V
0.0V
VSS
Undershoot
-0.5V
Time (ns)
Rev 1.5 / Feb. 2009
10
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
DC CHARACTERISTICS II (TA= -30 to 85oC)
Speed
Parameter
Symbol
Test Condition
Unit
Note
mA
1
166MHz 133MHz 105MHz
Operating Current
Precharge Standby
Current
in Power Down Mode
Precharge Standby
Current
in Non Power Down
Mode
IDD1
Burst length=1, One bank active
tRC ≥ tRC(min), IOL=0mA
IDD2P
CKE ≤ VIL(max), tCK = 15ns
0.3
mA
IDD2PS
CKE ≤ VIL(max), tCK = ∞
0.3
mA
IDD2N
IDD2NS
Active Standby Current IDD3P
in Power Down Mode IDD3PS
Active Standby Current IDD3N
in Non Power Down
Mode
IDD3NS
Burst Mode Operating
IDD4
Current
Auto Refresh Current
IDD5
Self Refresh Current
IDD6
Standby Current in
Deep Power Down
Mode
IDD7
60
45
CKE ≥ VIH(min), CS ≥ VIH(min), tCK
= 15ns
Input signals are changed one time
during
2clks.
All other pins ≥ VDD-0.2V or ≤ 0.2V
5
mA
CKE ≥ VIH(min), tCK = ∞
Input signals are stable.
1
CKE ≤ VIL(max), tCK = 15ns
5
CKE ≤ VIL(max), tCK = ∞
3
mA
CKE ≥ VIH(min), CS ≥ VIH(min), tCK
= 15ns
Input signals are changed one time
during
2clks.
All other pins ≥ VDD-0.2V or ≤ 0.2V
10
mA
CKE ≥ VIH(min), tCK = ∞
Input signals are stable.
tCK ≥ tCK(min), IOL=0mA
All banks active
5
60
50
tRFC ≥ tRFC(min),
CKE ≤ 0.2V
45
50
mA
1
100
mA
See Next Page
mA
2
10
uA
3
See the pages for the Deep Power
Down operation.
Notes:
1. IDD1 and IDD4 depend on output loading and cycle rates. Specified values are measured with the output open
2. See the tables of next page for more specific IDD6 current values.
3. Please contact Hynix office for more information and ability for DPD operation.
Deep Power Down operation is a hynix optional function.
Rev 1.5 / Feb. 2009
11
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
DC CHARACTERISTICS III - Low Power (IDD6)
Memory Array
Temp.
(oC)
4 Banks
2 Banks
1 Bank
45
250
220
200
uA
85
500
400
350
uA
Unit
1. VDD / VDDQ = 1.8V
2. Related numerical values in this 45oC are examples for reference sample value only.
3. With a on-chip temperature sensor of Mobile memory, auto temperature compensated self refresh will
automatically adjust the interval of self-refresh operation according to ambient temperature variations.
Rev 1.5 / Feb. 2009
12
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
AC CHARACTERISTICS I (AC operating conditions unless otherwise noted)
166MHz
Parameter
System Clock
Cycle Time
133MHz
105MHz
Symbol
Unit
Min
Max
Min
Max
Min
Max
Note
CAS Latency=3
tCK3
6.0
1000
7.5
1000
9.5
1000
ns
CAS Latency=2
tCK2
9.6
1000
12
1000
15
1000
ns
Clock High Pulse Width
tCHW
2.0
-
2.5
-
3.0
-
ns
1
Clock Low Pulse Width
tCLW
2.0
-
2.5
-
3.0
-
ns
1
CAS Latency=3
tAC3
-
5.4
-
6.0
-
7.0
ns
2, 3
CAS Latency=2
tAC2
-
6.0
-
8.0
-
10
ns
2, 3
Data-out Hold Time
tOH
2.6
-
2.6
-
2.6
-
ns
3
Data-Input Setup Time
tDS
2.0
-
2.0
-
3.0
-
ns
1
Data-Input Hold Time
tDH
1.0
-
1.0
-
1.5
-
ns
1
Address Setup Time
tAS
2.0
-
2.0
-
3.0
-
ns
1
Address Hold Time
tAH
1.0
-
1.0
-
1.5
-
ns
1
CKE Setup Time
tCKS
2.0
-
2.0
-
3.0
-
ns
1
CKE Hold Time
tCKH
1.0
-
1.0
-
1.5
-
ns
1
Command Setup Time
tCS
2.0
-
2.0
-
3.0
-
ns
1
Command Hold Time
tCH
1.0
-
1.0
-
1.5
-
ns
1
CLK to Data Output in Low-Z Time
tOLZ
1.0
-
1.0
-
1.0
-
ns
CLK to Data Output in
High-Z Time
CAS Latency=3
tOHZ3
5.4
6.0
7.0
ns
CAS Latency=2
tOHZ2
6.0
8.0
10
ns
Access Time From Clock
Notes:
1. Assume tR / tF (input rise and fall time) is 1ns. If tR & tF> 1ns, then [(tR+tF)/2-1]ns should be added to the parameter.
2. Access time to be measured with input signals of 1V/ns edge rate, from 0.8V to 0.2V. If tR> 1ns,
then (tR/2-0.5)ns should be added to the parameter.
3. Output Load: 30pF+No termination
●
●
●
●
●
AC high level input voltage / low level input voltage: 1.6 / 0.2V
Z = 50
Input timing measurement reference level: 0.9V
Output
Ω
tCK
tCH
CLK
1.6V
0.9V
0.2V
Input
1.6V
0.9V
0.2V
30pF
tSETUP
Transition time (input rise and fall time): 0.5ns
Output Load
Output timing measurement reference level: 0.9V
tCL
tHOLD
tAC
tOH
Output load: CL = 30pF
Rev 1.5 / Feb. 2009
Output
13
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
AC CHARACTERISTICS II (AC operating conditions unless otherwise noted)
166MHz
Parameter
133MHz
105MHz
Symbol
Unit Note
Min
Max
Min
Max
Min
Max
RAS Cycle Time
tRC
60
-
72.5
-
90
-
ns
RAS to CAS Delay
tRCD
18
-
22.5
-
28.5
-
ns
RAS Active Time
tRAS
42
100K
45
100K
60
100K
ns
RAS Precharge Time
tRP
18
-
22.5
-
28.5
-
ns
RAS to RAS Bank Active Delay
tRRD
12
-
15
-
19
-
ns
AUTO REFRESH Period
tRFC
72
-
72
-
72
-
ns
CAS to CAS Delay
tCCD
1
-
1
-
1
-
CLK
Write Command to Data-In Delay
tWTL
0
-
0
-
0
-
CLK
Data-in to Precharge Command
tDPL
2
-
2
-
2
-
CLK
Data-In to Active Command
tDAL
DQM to Data-Out Hi-Z
tDQZ
2
-
2
-
2
-
CLK
DQM to Data-In Mask
tDQM
0
-
0
-
0
-
CLK
MRS to New Command
tMRD
2
-
2
-
2
-
CLK
Precharge to Data Output CAS Latency=3
High-Z
CAS Latency=2
tPROZ3
3
-
3
-
3
-
CLK
tPROZ2
2
-
2
-
2
-
CLK
Power Down Exit Time
tDPE
1CLK
+
tCKS
-
1CLK
+
tCKS
-
1CLK
+
tCKS
-
CLK
Self Refresh Exit Time
tXSR
120
-
120
-
120
-
ns
Refresh Time
tREF
-
64
-
64
-
64
ms
Rev 1.5 / Feb. 2009
tDPL+tRP
14
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
FUNCTIONAL BLOCK DIAGRAM
8Mbit x 4banks x 16 I/O Mobile Synchronous DRAM
PASR
E x te nd ed
M od e
R eg ister
S elf refresh
lo g ic & tim er
Intern a l R o w
C oun ter
C LK
Output Buffer &
Logic
Rev 1.5 / Feb. 2009
A d d ress
R eg ister
Burst
Length
Address Buffers
A12
BA1
B A0
C o lu m n d ec od ers
DQ0
16
DQ15
C o lu m n A d d
C oun ter
B a nk Select
A0
A1
M em ory
C ell
A rra y
Sense AMP & I/O Gate
LD Q M ,
UDQM
C olu m n
P re
D ecod er
Row decoders
C o lu m n A ctive
WE
8M x 1 6 B a nk3
8 M x 1 6 B a nk2
8 M x 1 6 B a nk1
8 M x1 6 B a nk0
Row decoders
R efresh
Row decoders
CAS
State Machine
RAS
Row decoders
R o w A c tive
CKE
CS
R ow
P re
D eco d er
M od e R eg ister
B u rst
C ou nter
CAS
La tency
D a ta O u t C on trol
15
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
BASIC FUNCTIONAL DESCRIPTION
Mode Register
BA1
BA0
A12
A11
A10
A9
A8
A7
0
0
0
0
0
OP Code
0
0
A6
A5
A4
A3
CAS Latency
OP Code
BT
A2
A1
A0
Burst Length
Burst Type
A9
Write Mode
0
Burst Read and Burst Write
1
Burst Read and Single Write
CAS Latency
A3
Burst Type
0
Sequential
1
Interleave
Burst Length
A6
A5
A4
CAS Latency
0
0
0
Reserved
0
0
1
0
1
0
1
1
0
1
0
A2
A1
A0
Reserved
0
0
0
2
0
1
3
0
Reserved
1
Burst Length
A3 = 0
A3=1
0
1
1
0
1
2
2
0
1
0
4
4
0
1
1
8
8
Reserved
1
0
0
Reserved
Reserved
1
1
0
Reserved
1
0
1
Reserved
Reserved
1
1
1
Reserved
1
1
0
Reserved
Reserved
1
1
1
Full page
Reserved
Rev 1.5 / Feb. 2009
16
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
BASIC FUNCTIONAL DESCRIPTION (Continued)
Extended Mode Register
BA1
BA0
A12
A11
A10
A9
A8
1
0
0
0
0
0
0
A7
A6
A5
DS
A4
A3
0
0
A2
A1
A0
PASR
DS (Driver Strength)
A7
A6
A5
Driver Strength
0
0
0
Full
0
0
1
1/2 Strength
0
1
0
1/4 Strength
0
1
1
Reserved
1
0
0
3/4 Strength
PASR (Partial Array Self Refresh)
Rev 1.5 / Feb. 2009
A2
A1
A0
Self Refresh Coverage
0
0
0
All Banks
0
0
1
Half of Total Bank (BA1=0 or Bank 0,1)
0
1
0
Quarter of Total Bank (BA1=BA0=0 or Bank 0)
0
1
1
Reserved
1
0
0
Reserved
1
0
1
Half of Bank 0(Bank 0 and Row Address MSB=0)
1
1
0
Quarter of Bank 0(Bank 0 and Row Address 2 MSBs=0)
1
1
1
Reserved
17
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
COMMAND TRUTH TABLE
Function
CKEn
CS
RAS
CAS
WE
DQM
Mode Register Set
H
X
L
L
L
L
X
Op Code
2
Extended Mode Register
Set
H
X
L
L
L
L
X
Op Code
2
No Operation
H
X
L
H
H
H
X
X
Device Deselect
H
X
H
X
X
X
X
X
Bank Active
H
X
L
L
H
H
X
Read
H
X
L
H
L
H
Read with Autoprecharge
H
X
L
H
L
H
Write
H
X
L
H
L
L
Write with Autoprecharge
H
X
L
H
L
Precharge All Banks
H
X
L
L
H
Precharge selected Bank
H
X
L
L
H
Burst stop
H
X
L
H
H
Data Write/Output Enable
H
X
X
Data Mask/Output Disable
H
X
X
Auto Refresh
H
H
Self Refresh Entry
H
L
Self Refresh Exit
L
H
Precharge Power Down
Entry
H
L
Precharge Power Down Exit
L
H
Clock Suspend Entry
H
L
Clock Suspend Exit
L
H
Deep Power Down Entry
H
L
Deep Power Down Exit
L
H
L
L
ADDR
A10
/AP
CKEn-1
Row Address
BA
V
Column
L
V
X
Column
H
V
X
Column
L
V
L
X
Column
H
V
L
X
X
H
X
L
X
X
L
V
L
X
X
X
X
V
X
L
H
X
X
X
X
X
X
X
X
X
X
X
X
L
L
L
H
H
X
X
X
L
H
H
H
H
X
X
X
L
H
H
H
H
X
X
X
L
H
H
H
H
X
X
X
L
V
V
V
L
H
H
L
X
X
Note
X
X
X
X
X
X
1
Notes:
1. Exiting Self Refresh occurs by asynchronously bringing CKE from low to high.
2. BA1/BA0 must be issued 0/0 in the mode register set, and 1/0 in the extended mode register set.
Rev 1.5 / Feb. 2009
18
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
CURRENT STATE TRUTH TABLE (Sheet 1 of 4)
Command
Current
State
Idle
Row
Active
Read
CS RAS CAS WE
BA0/
BA1
L
L
L
L
L
L
L
H
X
L
L
H
L
L
L
H
L
H
L
Amax-A0
Notes
Mode Register Set
Set the Mode Register
14
X
Auto or Self Refresh
Start Auto or Self Refresh
5
BA
X
Precharge
No Operation
H
BA
Row Add.
Bank Activate
Activate the specified
bank and row
L
L
BA
Col. Add.
A10
Write/WriteAP
ILLEGAL
4
H
L
H
BA
Col. Add.
A10
Read/ReadAP
ILLEGAL
4
L
H
H
H
X
X
No Operation
No Operation
3
H
X
X
X
X
X
Device Deselect
No Operation or Power
Down
3
L
L
L
L
Mode Register Set
ILLEGAL
13,14
L
L
L
H
X
X
Auto or Self Refresh
ILLEGAL
13
L
L
H
L
BA
X
Precharge
Precharge
7
L
L
H
H
BA
Row Add.
Bank Activate
ILLEGAL
4
L
H
L
L
BA
Col Add.
A10
Write/WriteAP
Start Write: optional
AP(A10=H)
6
L
H
L
H
BA
Col Add.
A10
Read/ReadAP
Start Read: optional
AP(A10=H)
6
L
H
H
H
X
X
No Operation
No Operation
H
X
X
X
X
X
Device Deselect
No Operation
L
L
L
L
Mode Register Set
ILLEGAL
13,14
L
L
L
H
X
X
Auto or Self Refresh
ILLEGAL
13
L
L
H
L
BA
X
Precharge
Termination Burst: Start
the Precharge
L
L
H
H
BA
Row Add.
Bank Activate
ILLEGAL
L
H
L
L
BA
Col Add.
A10
Write/WriteAP
Termination Burst: Start
Write(optional AP)
8,9
L
H
L
H
BA
Col Add.
A10
Read/ReadAP
Termination Burst: Start
Read(optional AP)
8
L
H
H
H
X
X
No Operation
Continue the Burst
Rev 1.5 / Feb. 2009
OP CODE
Action
Description
OP CODE
OP CODE
4
19
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
CURRENT STATE TRUTH TABLE (Sheet 2 of 4)
Command
Current
State
Read
CS RAS CAS WE
BA0/
BA1
Amax-A0
X
X
Write with
Auto
Precharge
Notes
H
X
X
X
L
L
L
L
L
L
L
H
X
X
Auto or Self Refresh ILLEGAL
L
L
H
L
BA
X
Precharge
Termination Burst: Start
the Precharge
10
L
L
H
H
BA
Row Add.
Bank Activate
ILLEGAL
4
L
H
L
L
BA
Col Add.
A10
Write/WriteAP
Termination Burst: Start
Write(optional AP)
8
L
H
L
H
BA
Col Add.
A10
Read/ReadAP
Termination Burst: Start
Read(optional AP)
8,9
L
H
H
H
X
X
No Operation
Continue the Burst
H
X
X
X
X
X
Device Deselect
Continue the Burst
L
L
L
L
Mode Register Set
ILLEGAL
L
L
L
H
X
X
Auto or Self Refresh ILLEGAL
L
L
H
L
BA
X
Precharge
ILLEGAL
4,12
L
L
H
H
BA
Row Add.
Bank Activate
ILLEGAL
4,12
L
H
L
L
BA
Col Add. A10
Write/WriteAP
ILLEGAL
12
L
H
L
H
BA
Col Add. A10
Read/ReadAP
ILLEGAL
12
L
H
H
H
X
X
No Operation
Continue the Burst
H
X
X
X
X
X
Device Deselect
Continue the Burst
L
L
L
L
Mode Register Set
ILLEGAL
L
L
L
H
X
X
Auto or Self Refresh ILLEGAL
L
L
H
L
BA
X
Precharge
ILLEGAL
4,12
L
L
H
H
BA
Row Add.
Bank Activate
ILLEGAL
4,12
L
H
L
L
BA
Col Add. A10
Write/WriteAP
ILLEGAL
12
L
H
L
H
BA
Col Add. A10
Read/ReadAP
ILLEGAL
12
L
H
H
H
X
X
No Operation
Continue the Burst
H
X
X
X
X
X
Device Deselect
Continue the Burst
OP CODE
Write
Read with
Auto
Precharge
Action
Description
Rev 1.5 / Feb. 2009
OP CODE
OP CODE
Device Deselect
Continue the Burst
Mode Register Set
ILLEGAL
13,14
13
13,14
13
13,14
13
20
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
CURRENT STATE TRUTH TABLE (Sheet 3 of 4)
Command
Current
State
Precharging
Row
Activating
Write
Recovering
CS RAS CAS WE
BA0/
BA1
Amax-A0
Notes
L
L
L
L
L
L
L
H
X
X
Auto or Self Refresh ILLEGAL
L
L
H
L
BA
X
Precharge
No Operation:
Bank(s) idle after tRP
L
L
H
H
BA
Row Add.
Bank Activate
ILLEGAL
4,12
L
H
L
L
BA
Col Add. A10
Write/WriteAP
ILLEGAL
4,12
L
H
L
H
BA
Col Add. A10
Read/ReadAP
ILLEGAL
4,12
L
H
H
H
X
X
No Operation
No Operation:
Bank(s) idle after tRP
H
X
X
X
X
X
Device Deselect
No Operation:
Bank(s) idle after tRP
L
L
L
L
Mode Register Set
ILLEGAL
L
L
L
H
X
X
Auto or Self Refresh ILLEGAL
L
L
H
L
BA
X
Precharge
ILLEGAL
4,12
L
L
H
H
BA
Row Add.
Bank Activate
ILLEGAL
4,11,1
2
L
H
L
L
BA
Col Add. A10
Write/WriteAP
ILLEGAL
4,12
L
H
L
H
BA
Col Add. A10
Read/ReadAP
ILLEGAL
4,12
L
H
H
H
X
X
No Operation
No Operation: Row
Active after tRCD
H
X
X
X
X
X
Device Deselect
No Operation: Row
Active after tRCD
L
L
L
L
Mode Register Set
ILLEGAL
L
L
L
H
X
X
Auto or Self Refresh ILLEGAL
L
L
H
L
BA
X
Precharge
ILLEGAL
4,13
L
L
H
H
BA
Row Add.
Bank Activate
ILLEGAL
4,12
L
H
L
L
BA
Col Add. A10
Write/WriteAP
Start Write:
Optional AP(A10=H)
L
H
L
H
BA
Col Add. A10
Read/ReadAP
Start Read: Optional
AP(A10=H)
L
H
H
H
X
X
No Operation
No Operation:
Row Active after tDPL
Rev 1.5 / Feb. 2009
OP CODE
Action
Description
OP CODE
OP CODE
Mode Register Set
ILLEGAL
13,14
13
13,14
13
13,14
13
9
21
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
CURRENT STATE TRUTH TABLE (Sheet 4 of 4)
Command
Current
State
Write
Recovering
Write
Recovering
with Auto
Precharge
Refreshing
Mode
Register
Accessing
CS RAS CAS WE
BA0/
BA1
Amax-A0
X
X
Action
Notes
Description
Device Deselect
No Operation:
Row Active after tDPL
Mode Register Set
ILLEGAL
H
X
X
X
L
L
L
L
L
L
L
H
X
X
Auto or Self Refresh ILLEGAL
L
L
H
L
BA
X
Precharge
ILLEGAL
4,13
L
L
H
H
BA
Row Add.
Bank Activate
ILLEGAL
4,12
L
H
L
L
BA
Col Add. A10
Write/WriteAP
ILLEGAL
4,12
L
H
L
H
BA
Col Add. A10
Read/ReadAP
ILLEGAL
4,9,12
L
H
H
H
X
X
No Operation
No Operation:
Precharge after tDPL
H
X
X
X
X
X
Device Deselect
No Operation:
Precharge after tDPL
L
L
L
L
Mode Register Set
ILLEGAL
L
L
L
H
X
X
Auto or Self Refresh ILLEGAL
13
L
L
H
L
BA
X
Precharge
ILLEGAL
13
L
L
H
H
BA
Row Add.
Bank Activate
ILLEGAL
13
L
H
L
L
BA
Col Add. A10
Write/WriteAP
ILLEGAL
13
L
H
L
H
BA
Col Add. A10
Read/ReadAP
ILLEGAL
13
L
H
H
H
X
X
No Operation
No Operation:
idle after tRC
H
X
X
X
X
X
Device Deselect
No Operation:
idle after tRC
L
L
L
L
Mode Register Set
ILLEGAL
L
L
L
H
X
X
Auto or Self Refresh ILLEGAL
13
L
L
H
L
BA
X
Precharge
ILLEGAL
13
L
L
H
H
BA
Row Add.
Bank Activate
ILLEGAL
13
L
H
L
L
BA
Col Add. A10
Write/WriteAP
ILLEGAL
13
L
H
L
H
BA
Col Add. A10
Read/ReadAP
ILLEGAL
13
L
H
H
H
X
X
No Operation
No Operation:
idle after 2 clock cycles
H
X
X
X
X
X
Device Deselect
No Operation:
idle after 2 clock cycles
Rev 1.5 / Feb. 2009
OP CODE
OP CODE
OP CODE
13,14
13
13,14
13,14
22
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
Notes:
1. H: Logic High, L: Logic Low, X: Don't care, BA: Bank Address, AP: Auto Precharge.
2. All entries assume that CKE was active during the preceding clock cycle.
3. If both banks are idle and CKE is inactive, then in power down cycle
4. Illegal to bank in specified states. Function may be legal in the bank indicated by Bank Address,
depending on the state of that bank.
5. If both banks are idle and CKE is inactive, then Self Refresh mode.
6. Illegal if tRCD is not satisfied.
7. Illegal if tRAS is not satisfied.
8. Must satisfy burst interrupt condition.
9. Must satisfy bus contention, bus turn around, and/or write recovery requirements.
10. Must mask preceding data which don't satisfy tDPL.
11. Illegal if tRRD is not satisfied
12. Illegal for single bank, but legal for other banks in multi-bank devices.
13. Illegal for all banks.
14. Mode Register Set and Extended Mode Register Set is same command truth table except BA1.
Rev 1.5 / Feb. 2009
23
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
CKE Enable(CKE) Truth TABLE (Sheet 2 of 1)
Current
State
Self
Refresh
CKE
Command
Previous Current
CS
RAS
CAS
WE
Cycle
Cycle
H
X
X
X
X
L
H
H
X
L
H
L
L
H
L
Notes
A0
X
X
X
X
X
X
X
H
H
H
X
X
L
H
H
L
X
X
ILLEGAL
2
H
L
H
L
X
X
X
ILLEGAL
2
L
H
L
L
X
X
X
X
ILLEGAL
2
L
L
X
X
X
X
X
X
Maintain Self Refresh
H
X
X
X
X
X
X
X
INVALID
L
H
H
X
X
X
X
X
Power Down mode exit,
L
H
H
H
X
X
all banks idle
L
X
X
X
X
X
L
X
X
X
X
X
L
X
X
Down
L
Power
Action
BA1
Power
Deep
BA0, Amax-
H
L
INVALID
Exit Self Refresh with
Device Deselect
Exit Self Refresh with
No Operation
ILLEGAL
L
L
X
X
X
X
X
X
Maintain Power Down Mode
H
X
X
X
X
X
X
X
INVALID
L
H
X
X
X
X
X
X
L
L
X
X
X
X
X
X
Down
Rev 1.5 / Feb. 2009
Deep Power
Down mode exit
1
2
2
1
2
2
1
5
Maintain Deep
Power Down Mode
24
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
CKE Enable(CKE) Truth TABLE (Sheet 2 of 2)
Current
State
CKE
Command
Previous Current
CS
RAS
CAS
WE
BA0, AmaxBA1
Action
Notes
Cycle
Cycle
A0
H
H
H
X
X
X
Refer to the idle State section
3
H
H
L
H
X
X
of the Current State
3
H
H
L
L
H
X
Truth Table
3
H
H
L
L
L
H
X
All
H
H
L
L
L
L
OP CODE
Banks
H
L
H
X
X
Idle
H
L
L
H
H
L
L
H
L
H
L
X
Auto Refresh
Mode Register Set
4
X
Refer to the idle State section
3
X
X
of the Current State
3
L
H
X
Truth Table
3
L
L
L
H
X
X
Entry Self Refresh
4
L
L
L
L
L
OP CODE
Mode Register Set
X
X
X
X
X
X
Power Down
X
4
Refer to operations of
H
H
X
X
X
X
X
X
the Current State
Truth Table
Any State
other than
H
L
X
X
X
X
X
X
L
H
X
X
X
X
X
X
L
L
X
X
X
X
X
X
listed above
Begin Clock Suspend
next cycle
Exit Clock Suspend
next cycle
Maintain Clock Suspend
Notes:
1. For the given current state CKE must be low in the previous cycle.
2. When CKE has a low to high transition, the clock and other inputs are re-enabled asynchronously.
When exiting power down mode, a NOP (or Device Deselect) command is required on the first positive edge of
clock after CKE goes high.
3. The address inputs depend on the command that is issued.
4. The Precharge Power Down mode, the Self Refresh mode, and the Mode Register Set can only be entered
from the all banks idle state.
5. When CKE has a low to high transition, the clock and other inputs are re-enabled asynchronously.
When exiting deep power down mode, a NOP (or Device Deselect) command is required on the first positive edge of
clock after CKE goes high and is maintained for a minimum 200usec.
Rev 1.5 / Feb. 2009
25
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
Mobile SDR SDRAM OPERATION
State Diagram
Power
On
ACT :
Active
DPDSX
DPDS :
Enter Deep
Power-Down
Auto
Refresh
Precharge
All
Bank
DPDSX :
Exit Deep PowerDownEMRS
FA
RE
(EXTENDED)
Mode Register
Set
(E)MRS
EMRS :
Ext. Mode Reg.
Set
REFS
IDLE
REFX
Self
Refresh
MRS :
Mode Register Set
E
CK igh
H
DS
DP
E
CK w
Lo
PRE :
Precharge
DEEP
POWER
DOWN
C
Lo KE
w
WRITE
with AP
EA
W
Write
Read
READ
ROW
ACTIVE
Write
WRITE
E
CK w
Lo
WRITE
SUSPEND
PRE
E
PR
Manual input
Rev 1.5 / Feb. 2009
REFS :
Enter Self Refresh
REFSX :
Exit Self Refresh
READA :
Read with Auto
Precharge
WRITE :
Write w/o Auto
Precharge
WRITEA :
Write with Auto
Precharge
PR
E
Automatic Sequence
E
CK igh
H
C
H i KE
gh
READ
SUSPEND
REFA :
Auto Refresh
READ :
Read w/o Auto
Precharge
Read
C
Lo KE
w
WRITEA
SUSPEND
RI
T
ow
A
AD
RE
igh
CK
EL
CK
EH
READ
with AP
PREALL :
Precharge All
Banks
C
Hi KE
gh
E
CK igh
H
Active
Power
Down
ACT
E
CK w
Lo
READA
SUSPEND
Power
Down
Precharge
All
26
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
DESELECT
The DESELECT function (CS = High) prevents new commands from being executed by the Mobile SDRAM, the Mobile
SDRAM ignore command input at the clock. However, the internal status is held. The Mobile SDRAM is effectively deselected. Operations already in progress are not affected.
NO OPERATION
The NO OPERATION (NOP) command is used to perform a NOP to a Mobile SDRAM that is selected (CS = Low, RAS =
CAS = WE = High). This command is not an execution command. However, the internal operations continue. This prevents unwanted commands from being registered during idle or wait states. Operations already in progress are not
affected. (see to next figure)
ACTIVE
The Active command is used to activate a row in particular bank for a subsequent Read or Write access. The value of
the BA0,BA1 inputs selects the bank, and the address provided on A0-A12(or the highest address bit) selects the row.
This row remains active (or open) for accesses until a PRECHARGE command is issued to that bank. (see to next figure)
CLK
CKE
CLK
CKE
High
CS
CS
RAS
RAS
CAS
CAS
WE
WE
A0~A12
A0~A12
BA0,1
BA0,1
High
RA
Row Address
BA
Bank Address
Don't Care
NOP command
Rev 1.5 / Feb. 2009
Don't Care
ACTIVATING A SPECIFIC
ROW IN A SPECIFIC BANK
27
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
READ / WRITE COMMAND
Before executing a read or write operation, the corresponding bank and the row address must be activated by the
bank active (ACT) command. An interval of tRCD is required between the bank active command input and the following read/write command input.
The READ command is used to initiate a Burst Read to an active row. The value of BA0 and BA1 selects the bank and
address inputs select the starting column location.
The value of A10 determines whether or not auto precharge is used. If auto-precharge is selected, the row being
accessed will be precharged at the end of the read burst; if auto precharge is not selected, the row will remain open
for subsequent access. The valid data-out elements will be available CAS latency after the READ command is issued.
The WRITE command is used to initiate a Burst Write access to an active row. The value of BA0, BA1 selects the bank
and address inputs select the starting column location.
The value of A10 determines whether or not auto precharge is used. If auto-precharge is selected, the row being
accessed will be precharged at the end of the write burst; if auto precharge is not selected, the row will remain open
for subsequent access.
CLK
CKE
CLK
CKE
H ig h
CS
CS
RAS
RAS
CAS
CAS
WE
WE
A0 ~ A9
CA
A10
B A 0 ,1
BA
R ead Com m and
O p e ra tio n
A0 ~ A9
H ig h to E n a b le
A u to P re c h a rg e
A10
L o w to D is a b le
A u to P re c h a r g e
B A 0 ,1
D o n 't C a re
H ig h
CA
BA
W r ite C o m m a n d
O p e ra tio n
READ / WRITE COMMAND
Rev 1.5 / Feb. 2009
28
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
READ
A read operation starts when a read command is input. Output buffer becomes Low-Z in the (/CAS Latency - 1)
cycle after read command set. The SDRAM can perform a burst read operation.
The burst length can be set to 1, 2, 4 and 8. The start address for a burst read is specified by the column address and
the bank select address at the read command set cycle. In a read operation, data output starts after the number of
clocks specified by the /CAS Latency. The /CAS Latency can be set to 2 or 3.
When the burst length is 1, 2, 4 and 8 the DOUT buffer automatically becomes High-Z at the next clock after the successive burst-length data has been output.
The /CAS latency and burst length must be specified at the mode register.
tCK
CLK
Command
REA
D
NOP
NOP
tLZ
DQ
tOH
Do0
Do1
Do2
Do3
Do1
Do2
tAC
CL = 2
Command
REA
D
NOP
NOP
NOP
tLZ
tOH
Do0
DQ
Do3
tAC
CL = 3
Undefined
Don't Care
Read Burst Showing CAS Latency
Rev 1.5 / Feb. 2009
29
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
READ to READ
Data from a read burst may be concatenated or truncated by a subsequent READ command. The first data from the
new burst follows either the last element of a completed burst or the last desired element of a longer burst that is
being truncated.
When another read command is executed at the same ROW address of the same bank as the preceding read command execution, the second read can be performed after an interval of no less than 1 clock. Even when the first command is a burst read that is not yet finished, the data read by the second command will be valid.
CLK
Command
Address
READ
NOP
NOP
READ’
BA, Col
BA, Col
a
b
CL =2
DQ
Do a0
Do a1
Do b0
Do b1
Do a1
Do b0
CL =3
DQ
Do a0
Don't Care
Consecutive Read Bursts
Rev 1.5 / Feb. 2009
30
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
CLK
Command
Address
READ
READ
BA, Col
BA, Col
n
b
CL =2
DQ
Dob
Don
CL =3
Dob
Don
DQ
Don't Care
1) Don (or b): Data out from column n
2) BA, Col n (b) = Bank A, Column n (b)
3) Burst Length = 4 : 3 subseqnent elements of Data Out appear in the programmed order following Do n (b)
Non-Consecutive Read Bursts
CLK
Command
READ
READ
READ
READ
Address
BA, Col
BA, Col
BA, Col
BA, Col
n
x
b
g
CL =2
DQ
Don
Don'
Dox
Dox'
Dob
Dob'
Dog
Dog'
Don
Don'
Dox
Dox'
Dob
Dob'
Dog
CL =3
DQ
1) Don, etc: Data out from column n, etc
n', x', etc : Data Out elements, accoding to the programmd burst order
2) BA, Col n = Bank A, Column n
3) Burst Length = 1, 2, 4, 8 or full page in cases shown
4) Read are to active row in any banks
Dog’
Don't Care
Random Read Bursts
Rev 1.5 / Feb. 2009
31
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
READ BURST TERMINATE
Data from any READ burst may be truncated with a BURST TERMINATE command. The BURST TERMINATE latency is
equal to the read (CAS) latency, i.e., the BURST TERMINATE command should be issued X cycles after the READ command where X equals the desired data-out element.
CLK
Com m and
Address
READ
BURST
BA, Col
n
CL =2
DQ
Do n
Do n'
CL =3
Do n
DQ
Do n'
1) Do n : Data out from column n
2) BA, Col n = Bank A, Column n
3) Cases shown are bursts of 4, 8, or full page terminated after 2 data elem ents
Don't Care
Terminating a Read Burst
Rev 1.5 / Feb. 2009
32
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
READ to WRITE
Data from READ burst must be completed or truncated before a subsequent WRITE command can be issued. If truncation is necessary, the BURST TERMINATE command must be used, as shown in next fig.
CLK
Com m and
Address
READ
BURST
W RITE
BA, Col
BA, Col
n
b
CL = 2
DQ
Do n
Do n'
D I b0
D I b1
D I b2
DI b3
D I b0
D I b1
D I b2
D I b3
CL = 3
D on
DQ
D o n'
1) D O n = D ata Out from colum n n; DI b = D ata In to colum n b
D on't Care
Read to Write
Notes:
1. Same bank, same ROW address: When the write command is executed at the same ROW address of the same bank
as the preceding read command, the write command can be performed after an interval of no less than 1 clock.
However, DQM must be set High so that the output buffer becomes High-Z before data input.
2. Same bank, different ROW address: When the ROW address changes, consecutive write commands cannot be
executed; it is necessary to separate the two commands with a precharge command and a bank active command.
3. Different bank: When the bank changes, the write command can be performed after an interval of no less than 1
cycle, provided that the other bank is in the bank active state. However, DQM must be set High so that the output
buffer becomes High-Z before data input.
Rev 1.5 / Feb. 2009
33
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
READ to PRECHARGE
Following the PRECHARGE command, a subsequent command to the same bank cannot be issued until tRP is met.
Note that part of the row precharge time is hidden during the access of the last data element(s).
In the case of a fixed-length burst being executed to completion, a PRECHARGE command issued at the optimum time
(as described above) provides the same operation that would result from the same fixed-length burst with auto precharge.
The disadvantage of the PRECHARGE command is that it requires that the command and address buses be available at
the appropriate time to issue the command; the advantage of the PRECHARGE command is that it can be used to truncate fixed-length or full-page bursts.
CLK
Com m and
R EAD
PRE
BA, Col
Bank
A, All
ACT
tRP
Address
n
BA,
Row
CL = 2
DQ
D on
CL = 3
Don
DQ
D on't Care
1) D O n = D ata O ut from colum n n
2) Note that Precharge m ay not be issued before tRAS ns after the ACTIVE com m and for applicable banks.
3) The ACTIVE com m and m ay be applied if tRC has been m et.
READ to PRECHARGE
Rev 1.5 / Feb. 2009
34
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
Write
Input data appearing on the data bus, is written to the memory array subject to the DM input logic level appearing
coincident with the data. If a given DM signal is registered Low, the corresponding data will be written to the memory;
if the DM signal is registered High, the corresponding data inputs will be ignored, and a write will not be executed to
that byte / column location.
During WRITE bursts, the first valid data-in element will be registered coincident with the WRITE command. Subsequent data elements will be registered on each successive positive clock edge. Upon completion of a fixed-length
burst, assuming no other commands have been initiated, the DQ will remain High-Z and any additional input data will
be ignored. A full-page burst will continue until terminated.
Data for any WRITE burst may be truncated with a subsequent WRITE command, and data for a fixed-length WRITE
burst may be immediately followed by data for a WRITE command. The new WRITE command can be issued on any
clock following the previous WRITE command, and the data provided coincident with the new command applies to the
new command.
CLK
Command
WRITE
Address
BA, Col
b
DQ
D Ib0
DQ
D Ib0
D Ib1
DQ
D Ib0
D Ib1
D Ib2
D Ib3
DQ
D Ib0
D Ib1
D Ib2
D Ib3
BL = 1
BL = 2
BL = 4
D Ib4
D Ib5
D Ib6
D Ib7
BL = 8
CL = 2 or 3
Basic Write timing parameters for
Don't Care
Write Burst Operation
Notes:
1. Same bank, same ROW address: When another write command is executed at the same ROW address of the same
bank as the preceding write command, the second write can be performed after an interval of no less than 1 clock.
In the case of burst writes, the second write command has priority.
2. Same bank, different ROW address: When the ROW address changes, consecutive write commands cannot be
executed; it is necessary to separate the two write commands with a precharge command and a bank active
command.
3. Different bank: When the bank changes, the second write can be performed after an interval of no less than 1 clock,
provided that the other bank is in the bank active state. In the case of burst write, the second write command has
priority.
Rev 1.5 / Feb. 2009
35
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
WRITE to WRITE
Data for any WRITE burst may be concatenated with or truncated with a subsequent WRITE command. In either case,
a continuous flow of input data, can be maintained. The new WRITE command can be issued on any positive edge of
the clock following the previous WRITE command. The first data-in element from the new burst is applied after either
the last element of a completed burst or the last desired data element of a longer burst which is being truncated. The
new WRITE command should be issued X cycles after the first WRITE command, where X equals the number of
desired data-in element.
CLK
Command
WRITE
WRITE
Address
BA, Col
BA, Col
b
n
DQ
D Ib0
D Ib1
D Ib2
D Ib3
D In0
D In1
D In2
D In3
DM
CL = 2 or 3
Don't Care
Concatenated Write Bursts
CLK
Com m and
W RITE
W RITE
W RITE
W RITE
W RITE
Address
BA, Col
BA, Col
BA, Col
BA, Col
BA, Col
b
x
n
a
g
DQ
D Ib
D I b'
D Ix
D I x’
D In
D I n’
D Ia
D I a’
D Ig
N OP
D I g’
DM
CL = 2 or 3
D on't Care
Random Write Cycles
Rev 1.5 / Feb. 2009
36
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
WRITE to READ
CLK
Command
WRITE
READ
Address
BA, Col
BA, Col
b
n
DIb0
DIb1
DIb0
DIb1
DO n0
DO n1
DOn2
DOn0
DOn1
CL = 2
DOn3
BL = 4
DQ
DQ
D On2
DOn3
CL = 3 BL = 4
Don't Care
The preceding burst write operation can be aborted and a new burst read operation can be started by inputting a new
read command in the write cycle. The data of the read command (READ) is output after the lapse of the /CAS latency.
The preceding write operation (WRIT) writes only the data input before the read command.
The data bus must go into a high-impedance state at least one cycle before output of the latest data.
Notes:
1. Same bank, same ROW address: When the read command is executed at the same ROW address of the same bank
as the preceding write command, the read command can be performed after an interval of no less than 1 clock.
However, in the case of a burst write, data will continue to be written until one clock before the read command is
executed.
2. Same bank, different ROW address: When the ROW address changes, consecutive read commands cannot be
executed; it is necessary to separate the two commands with a precharge command and a bank active command.
3. Different bank: When the bank changes, the read command can be performed after an interval of no less than 1
clock, provided that the other bank is in the bank active state. However, in the case of a burst write, data will
continue to be written until one clock before the read command is executed (as in the case of the same bank and
the same address).
Rev 1.5 / Feb. 2009
37
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
WRITE to PRECHARGE
Data for any WRITE burst may be followed by a subsequent PRECHARGE command to the same bank (provided Auto
Precharge was not activated). When the precharge command is executed for the same bank as the write command
that preceded it, the minimum interval between the two commands is 1 clock. However, if the burst write operation is
unfinished, the input data must be masked by means of DQM for assurance of the clock defined by tDPL. To follow a
WRITE without truncating the WRITE burst, tDPL should be met as shown in Fig.
CLK
Command
WRITE
Address
BA, Col
DQ
PRE
b
D Ib0
D Ib1
D IO b2
CL = 2 or 3
D Ib3
BL = 4
tDPL
Non-Interrupting Write to Precharge
Data for any WRITE burst may be truncated by a subsequent PRECHARGE command as shown in Figure.
Note that only data-in that are registered prior to the tDPL period are written to the internal array, and any subsequent
data-in should be masked with DM, as shown in next Fig. Following the PRECHARGE command, a subsequent command to the same bank cannot be issued until tRP is met.
CLK
Command
WRITE
Address
BA, Col
PRE
b
DIb0
DIb1
CL = 2 or 3
DIOb2
BL = 4
DQ
tDPL
Interrupting Write to Precharge
Rev 1.5 / Feb. 2009
38
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
WRITE BURST TERMINATE
WRITE bursts can be truncated with the BURST TERMINATE command. When truncating a WRITE burst, the input
data applied coincident with the BURST TERMINATE command will be ignored. The last data written (provided that
DQM is LOW at that time) will be the input data applied one clock previous to the BURST TERMINATE command.
CLK
Command
WRITE
Address
BA, Col
BST
b
DIb0
DIb1
DIOb2
High-Z
BL = 4 or higher
CL = 2 or 3
DQ
Don’ t care - Data ignored
Terminating a Burst Write command with BST
Rev 1.5 / Feb. 2009
39
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
BURST TERMINATE
The BURST TERMINATE command is used to truncate read bursts or write bursts (with auto precharge disabled). The
most recently registered READ or WRITE command prior to the BURST TERMINATE command will be truncated, as
shown in the Operation section of this datasheet. The BURST TERMINATE command is not bank specific.
CLK
CKE
High
CS
RAS
CAS
WE
A0~A12
Don't Care
BA0, 1
BURST TERMINATE COMMAND
Rev 1.5 / Feb. 2009
40
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
PRECHARGE
The PRECHARGE command is used to deactivate the open row in a particular bank or the open row in all banks.
Another command to the same bank (or banks) being precharged must not be issued until the precharge time (tRP) is
completed.
If one bank is to be precharged, the particular bank address needs to be specified. If all banks are to be precharged,
A10 should be set high along with the PRECHARGE command. If A10 is high, BA0 and BA1 are ignored. A PRECHARGE
command will be treated as a NOP if there is no open row in that bank, or if the previously open row is already in the
process of precharging.
CKE
High
A10 defines the precharge
mode when a precharge
command, a read command
or a write command is
issued.
CS
RAS
If A10 = High when a
precharge command is
issued, all banks are
precharged.
CAS
If A10 = Low when a
precharge command is
issued, only the bank that is
selected by BA1/BA0 is
precharged.
WE
A0~A9
A11, A12
If A10 = High when read or
write command, autoprecharge function is
enabled.
While A10 = Low, autoprecharge function is
disabled.
A10
BA0,1
BA
Bank Address
Don't Care
PRECHARGE command
AUTO PRECHARGE
Auto Precharge is a feature which performs the same individual bank precharge function as described above, but without requiring an explicit command.
This is accomplished by using A10 (A10=high), to enable auto precharge in conjunction with a specific Read or Write
command. This precharges the bank/row after the Read or Write burst is complete.
Auto precharge is non persistent, so it should be enabled with a Read or Write command each time auto precharge is
desired. Auto precharge ensures that a precharge is initiated at the earliest valid stage within a burst.
The user must not issue another command to the same bank until the precharge time (tRP) is completed.
Rev 1.5 / Feb. 2009
41
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
AUTO REFRESH AND SELF REFRESH
Mobile SDRAM devices require a refresh of all rows in any rolling 64ms interval. Each refresh is generated in one of two
ways: by an explicit AUTO REFRESH command, or by an internally timed event in SELF REFRESH mode:
- AUTO REFRESH.
This command is used during normal operation of the Mobile SDRAM. It is non persistent, so must be issued each time
a refresh is required. The refresh addressing is generated by the internal refresh controller.The Mobile SDRAM requires
AUTO REFRESH commands at an average periodic interval of tREF.
To allow for improved efficiency in scheduling and switching between tasks, some flexibility in the absolute refresh
interval is provided. A maximum of eight AUTO REFRESH commands can be posted to any given Mobile SDRMA, and
the maximum absolute interval between any AUTO REFRESH command and the next AUTO REFRESH command is
8*tREF.
-SELF REFRESH.
This state retains data in the Mobile SDRAM, even if the rest of the system is powered down. Note refresh interval timing while in Self Refresh mode is scheduled internally in the Mobile SDRAM and may vary and may not meet tREF time.
After executing a self-refresh command, the self-refresh operation continues while CKE is held Low. During self refresh
operation, all ROW addresses are refreshed by the internal refresh timer. A self-refresh is terminated by a self-refresh
exit command. Before and after self-refresh mode, execute auto-refresh to all refresh addresses in or within tREF
(max.) period on the condition 1 and 2 below.
1. Enter self-refresh mode within time as below* after either burst refresh or distributed refresh at equal interval to all
refresh addresses are completed.
2. Start burst refresh or distributed refresh at equal interval to all refresh addresses within time as below* after exiting
from self-refresh mode.
Note: tREF (max.) / refresh cycles.
The use of SELF REFRESH mode introduces the possibility that an internally timed event can be missed when CKE is
raised for exit from self refresh mode. Upon exit from SELF REFRESH an extra AUTO REFRESH command is recommended. In the self refresh mode, two additional power-saving options exist. They are Temperature Compensated Self
Refresh and Partial Array Self Refresh and are described in the Extended Mode Register section.
The Self Refresh command is used to retain cell data in the Mobile SDRAM. In the Self Refresh mode, the Mobile
SDRAM operates refresh cycle asynchronously.
The Self Refresh command is initiated like an Auto Refresh command except CKE is disabled(Low). The Mobile SDRAM
can accomplish an special Self Refresh operation by the specific modes(PASR) programmed in extended mode registers. The Mobile SDRAM can control the refresh rate automatically by the temperature value of Auto TCSR(Temperature Compensated Self Refresh) to reduce self refresh current and select the memory array to be refreshed by the
value of PASR(Partial Array Self Refresh). The Mobile SDRAM can reduce the self refresh current(IDD6) by using these
two modes.
Rev 1.5 / Feb. 2009
42
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
CLK
CLK
CKE
CKE
High
CS
CS
RAS
RAS
CAS
CAS
WE
WE
A0~A12
A0~A12
Don't Care
BA0, 1
Don't Care
BA0, 1
AUTO REFRESH COMMAND
SELF REFRESH ENTRY COMMAND
Note 1: If all banks are in the idle status and CKE is inactive (low level), the self refresh mode is set.
Function
CKEn-1
CKEn
CS
RAS
CAS
WE
DQM
Auto Refresh
H
H
L
L
L
H
X
X
Self Refresh Entry
H
L
L
L
L
H
X
X
Rev 1.5 / Feb. 2009
ADDR
A10/AP
BA
43
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
MODE REGISTER SET
The mode registers are loaded via the address bits.
BA0 and BA1 are used to select between the Mode Register and the Extended Mode Register. See the Mode Register
description in the register definition section. The MODE REGISTER SET command can only be issued when all banks
are idle and no bursts are in progress, and a subsequent executable command cannot be issued until tMRD is met.
CLK
CKE
H igh
CS
RAS
CAS
WE
A 0~ A 12
Cod e
BA0, 1
Cod e
D on 't C are
MODE REGISTER SET COMMAND
Note: BA0=BA1=Low loads the Mode Register, whereas BA0=Low and BA1=High loads the Extended Mode Register.
CLK
Command
MRS
NOP
Valid
tMRD
Address
Code
Valid
Don't Care
Code = Mode Register / Extended Mode Register selection
(BA0, BA1) and op-code (A0 - An)
tMRD DEFINITION
Rev 1.5 / Feb. 2009
44
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
POWER DOWN
Power down occurs if CKE is set low coincident with Device Deselect or NOP command and when no accesses are in
progress. If power down occurs when all banks are idle, it is Precharge Power Down.
If Power down occurs when one or more banks are Active, it is referred to as Active power down. The device cannot
stay in this mode for longer than the refresh requirements of the device, without losing data. The power down state is
exited by setting CKE high while issuing a Device Deselect or NOP command.
If power-down occurs when all banks are idle, this mode is referred to as precharge power-down; if power-down
occurs when there is a row active in any bank, this mode is referred to as active power-down. Entering power-down
deactivates the input and output buffers, excluding CKE, for maximum power savings while in standby.
DEEP POWER-DOWN
The Deep Power-Down (DPD) mode enables very low standby currents. All internal voltage generators inside the
Mobile SDRAM are stopped and all memory data is lost in this mode.
All the information in the Mode Register and the Extended Mode Register is lost. Next Figure, DEEP POWER-DOWN
COMMAND shows the DEEP POWER-DOWN command All banks must be in idle state with no activity on the data bus
prior to entering the DPD mode. While in this state, CKE must be held in a constant low state.
To exit the DPD mode, CKE is taken high after the clock is stable and NOP command must be maintained for at least
200 us. After 200 us a complete re-initialization routing is required defined for the initialization sequence.
CLK
CLK
CKE
CKE
CS
CS
RAS
RAS
CAS
CAS
WE
WE
A0~A12
A0~A12
BA0, 1
BA0, 1
Don't Care
POWER-DOWN COMMAND
Rev 1.5 / Feb. 2009
Don't Care
DEEP POWER-DOWN COMMAND
45
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
CLK
CKE
COMMAND
NOP
NOP
ACTIVE
All banks idle
tRCD
Input buffers gated off
Enter power-down mode.
tRAS
Exit power-down mode.
tRC
DON’ T CARE
CLK
CKE
tCKS
COMMAND
PCG
NOP
tCKS
NOP
NOP
Input buffers gated off
Pre-charge all
Deep Power down entry
APCG
200us(min)
Deep Power down Exit
DON’T CARE
Rev 1.5 / Feb. 2009
46
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
CLK
tCKS
tCKS
tCKS
tCKS
CKE
Power down Exit Time
CS
RAS
CAS
WE
Ra
VDDR
Ca
BA0, BA1
Ra
AP
Hi-Z
Qa0
DQ
Qa1
Qa2
DQM
Row Active
Precharge
Power down
Entry
Precharge
Power down
Exit
Active
Power down
Entry
Read
Active
Power down
Exit
Precharge
Don’ t care
Note : CKE should be set high at least 1CLK + tCKS prior to Row active command.
Rev 1.5 / Feb. 2009
47
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
tCK
tCH
CLK
tCKS
tCL
tCKS
tCKH
tRAS(MIN)
CKE
tCMS
COMMAND
tCMH
PRECHARGE
NOP
AUTO
REFRESH
NOP
or COMMAND
INHIBIT
Any COM
DQM
A0A9,Amax
ALL BANKS
A10
SINGLE BANK
tAS
BANKS
BA0, BA1
DQ
tAH
High-Z
Precharge all
active banks
Rev 1.5 / Feb. 2009
tRP
Enter self refresh mode
tXSR
Exit self refresh mode
(Restart refresh time base)
DON’ T CARE
48
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
Power-up and Initialization
Like a Synchronous DRAM, Low Power SDRAM(Mobile SDRAM) must be powered up and initialized in a predefined manner. Power must be applied to VDD and VDDQ(simultaneously). The clock signal must be started at the same time. After
power up, an initial pause of 200 usec is required. And a precharge all command will be issued to the Mobile SDRAM.
Then, 8 or more Auto refresh cycles will be provided. After the Auto refresh cycles are completed, a mode register
set(MRS) command will be issued to program the specific mode of operation (Cas Latency, Burst length, etc.) And a
extended mode register set command will be issued to program specific mode of self refresh operation(PASR). The following these cycles, the Mobile SDRAM is ready for normal operation.
Programming the registers
Mode Register
The mode register contains the specific mode of operation of the Mobile SDRAM. This register includes the selection of
a burst length(1, 2, 4, 8, Full Page), a cas latency(2 or 3), a burst type. The mode register set must be done before any
activate command after the power up sequence. Any contents of the mode register be altered by re-programming the
mode register through the execution of mode register set command.
Extended Mode Register
The extended mode register contains the specific features of self refresh operation of the Mobile SDRAM. This register
includes the selection of partial arrays to be refreshed(half array, quarter array, etc.). The extended mode register set
must be done before any activate command after the power up sequence. Any contents of the mode register be altered
by re-programming the mode register through the execution of extended mode register set command.
Bank(Row) Active
The Bank Active command is used to activate a row in a specified bank of the device. This command is initiated by
activating CS, RAS and deasserting CAS, WE at the positive edge of the clock. The value on the BA1 and BA0 selects
the bank, and the value on the A0-A12 selects the row. This row remains active for column access until a precharge
command is issued to that bank. Read and write operations can only be initiated on this activated bank after the minimum tRCD time is passed from the activate command.
Read
The READ command is used to initiate the burst read of data. This command is initiated by activating CS, CAS, and
deasserting WE, RAS at the positive edge of the clock. BA1 and BA0 inputs select the bank, A9-A0 address inputs select
the starting column location. The value on input A10 determines whether or not Auto Precharge is used. If Auto Precharge is selected the row being accessed will be precharged at the end of the READ burst; if Auto Precharge is not
selected, the row will remain active for subsequent accesses.
The length of burst and the CAS latency will be determined by the values programmed during the MRS command.
Write
The WRITE command is used to initiate the burst write of data. This command is initiated by activating CS, CAS, WE
and deasserting RAS at the positive edge of the clock. BA1 and BA0 inputs select the bank, A9-A0 address inputs select
the starting column location. The value on input A10 determines whether or not Auto Precharge is used.
If Auto Precharge is selected the row being accessed will be precharged at the end of the WRITE burst; if Auto Precharge is not selected, the row will remain active for subsequent accesses.
Rev 1.5 / Feb. 2009
49
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
Precharge
The Precharge command is used to close the open row in a particular bank or the open row in all banks. When the
precharge command is issued with address A10, high, then all banks will be precharged, and If A10 is low, the open
row in a particular bank will be precharged. The bank(s) will be available when the minimum tRP time is met after the
precharge command is issued.
Auto Precharge
The Auto Precharge command is issued to close the open row in a particular bank after READ or WRITE operation. If
A10 is high when a READ or WRITE command is issued, the READ or WRITE with Auto Precharge is initiated.
Burst Termination
The Burst Termination is used to terminate the burst operation. This function can be accomplished by asserting a Burst
Stop command or a Precharge command during a burst READ or WRITE operation. The Precharge command interrupts
a burst cycle and close the active bank, and the Burst Stop command terminates the existing burst operation leave the
bank open.
Data Mask
The Data Mask command is used to mask READ or WRITE data. During a READ operation, When this command is issued, data outputs are disabled and become high impedance after two clock delay. During a WRITE operation, When
this command is issued, data inputs can't be written with no clock delay.
If data mask is initiated by asserting low on DQM during the read cycle, the data outputs are enabled.
If DQM is asserted to High. the data outputs are masked (disabled) and become Hi-Z state after 2 cycle later. During
the write cycle, DQM mask data input with zero latency
CK
W RIT
CM D
DM
Data M asking
H i- Z
D 0D IN0 D 1
DQ
D ata M asking
0 Latency
D0 MK
D1
0 Latency
D 0D IN2 D 1
D0 MK D1
W rite D ata M asking
CK
CMD
READ
DM
D a ta M asking
2 Laten cy
H i- Z
DQ
D0
D O U T 0D 1
D0
D O U T1D 1
D0
D D O T 2D 1
D0 MK
D1
R ead D ata M askin g
Rev 1.5 / Feb. 2009
50
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
Clock Suspend
The Clock Suspend command is used to suspend the internal clock of Mobile SDRAM. The clock suspend operation stops
transmission of the clock to the internal circuits of the device during burst transfer of data to stop the operation of the
device. During normal access mode, CKE is keeping High. When CKE is low, it freezes the internal clock and extends
data Read and Write operations. (See examples in next Figures)
CLK
Command
RD
CKE
Masked by CKE
Internal CLK
Frozen Int. CLK by CKE
(CKE = Fixed Low)
DQ
Q1
Q2
Q3
Q4
Clock Suspend
Mode
Command
WR
CKE
Masked by CKE
Internal CLK
Frozen Int. CLK by CKE
(CKE = Fixed Low)
DQ
D1
D2
D3
D4
Clock Suspend
Mode
Rev 1.5 / Feb. 2009
51
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
Power Down
The Power Down command is used to reduce stand-by current. Before this command is issued, all banks must be precharged and tRP must be passed after a precharge command. Once the Power Down command is initiated by keeping
CKE low, all of the input buffer except CKE are gated off.
Auto Refresh
The Auto Refresh command is used during normal operation and is similar to CBR refresh in Conventional DRAMs.
This command must be issued each time a refresh is required. When an Auto Refresh command is issued, the address
bits is ''Don't care'', because the specific address bits is generated by internal refresh address counter.
Self Refresh
The Self Refresh command is used to retain cell data in the Mobile SDRAM. In the Self Refresh mode, the Mobile SDRAM
operates refresh cycle asynchronously.
The Self Refresh command is initiated like an Auto Refresh command except CKE is disabled(Low). The Mobile SDRAM
can accomplish an special Self Refresh operation by the specific modes(PASR) programmed in extended mode registers.
The Mobile SDRAM can control the refresh rate automatically by the temperature value of Auto TCSR(Temperature
Compensated Self Refresh) to reduce self refresh current and select the memory array to be refreshed by the value of
PASR(Partial Array Self Refresh). The Mobile SDRAM can reduce the self refresh current(IDD6) by using these two
modes.
Deep Power Down
The Deep Power Down Mode is used to achieve maximum power reduction by cutting the power of the whole memory
array of the devices.
For more information, see the special operation for Low Power consumption of this data sheet.
Rev 1.5 / Feb. 2009
52
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
Special Operation for Low Power Consumption
Deep Power Down Mode
Deep Power Down Mode is an operating mode to achieve maximum power reduction by cutting the power of the whole
memory array of the devices.
Data will not be retained once the device enters Deep Power Down Mode.
Full initialization is required when the device exits from Deep Power Down Mode.
Truth Table
Current State
Command
CKEn-1
CKEn
CS
RAS
CAS
WE
Idle
Deep Power Down Entry
H
L
L
H
H
L
Deep Power Down
Deep Power Down Exit
L
H
X
X
X
X
Deep Power Down Mode Entry
The Deep Power Down Mode is entered by having CS and WE held low with RAS and CAS high at the rising edge of the
clock, while CKE is low. The following diagram illustrates deep power down mode entry.
CKE
CS
RAS
CAS
WE
tRP
Pre-charge
if needed
Rev 1.5 / Feb. 2009
Deep Power
Down Entry
53
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
Deep Power Down Mode (Continued)
Deep Power Down Mode Exit Sequence
The Deep Power Down mode is exited by asserting CKE high.
After the exit, the following sequence is needed to enter a new command.
1. Maintain NOP input conditions for a minimum of 200usec
2. Issue precharge commands for all banks of the device
3. Issue 8 or more auto refresh commands
4. Issue a mode register set command to initialize the mode register
5. Issue an extended mode register set command to initialize the extended mode register
The following timing diagram illustrates deep power down mode exit sequence.
CLK
CKE
CS
RAS
CAS
WE
200us
Deep Power Down Exit
Rev 1.5 / Feb. 2009
tRP
All Banks
Precharge
tRC
Auto
Refresh
Auto
Refresh
Mode
Register
Set
Extended
Mode
Register
Set
New
Command
Accepted
Here
54
11
512Mbit (32Mx16bit) Mobile SDR Memory
H55S5162DFR Series
PACKAGE INFORMATION
54 Ball FBGA 0.8mm pitch (8mm x 8mm)
A1 INDEX MARK
8.00 Typ.
3.20
0.8
+/-0.01
8.0 Typ.
1.60
Unit
[mm]
0.80 Typ.
Bottom
View
0.45
+/- 0.05
0.35
+/- 0.05
1.8
+/-0.01
1.375
Rev 1.5 / Feb. 2009
0.80
Typ.
1.00 max
55