HYNIX HYMD532M646AL6-H

32Mx64 bits
Unbuffered DDR SO-DIMM
HYMD532M646A(L)6-J/K/H
Document Title
32Mx64 bits Unbuffered DDR SO-DIMM
Revision History
No.
History
Draft Date
0.1
Defined Target Spec.
Jan. 2003
0.2
Defined Cap. Spec.
Nov. 2003
0.3
1) Reflected a “notational” change in module thickness on page 14 - Not Real ! 2) Corrected some typos
Apr. 2004
0.4
1) Corrected some typo - tRAS.min = 45ns for -H(266B) at page 10
2) Modified the side view of module including additional device at page 14
Oct. 2004
Remark
This document is a general product description and is subject to change without notice. Hynix Semiconductor does not assume any
responsibility for use of circuits described. No patent licenses are implied.
Rev. 0.4/ Oct. 2004
1
32Mx64 bits
Unbuffered DDR SO-DIMM
HYMD532M646A(L)6-J/K/H
DESCRIPTION
Preliminary
Hynix HYMD532M646A(L)6-J/K/H series is unbuffered 200-pin double data rate Synchronous DRAM Small Outline
Dual In-Line Memory Modules (SO-DIMMs) which are organized as 32Mx64 high-speed memoryarrays. Hynix
HYMD532M646A(L)6-J/K/H series consists of four 32Mx16 DDR SDRAM in 400mil TSOP II packages on a 200pin
glass-epoxy substrate. Hynix HYMD532M646A(L)6-J/K/H series provide a high performance 8-byte interface in
67.60mmX 31.75mm form factor of industry standard. It is suitable for easy interchange and addition.
Hynix HYMD532M646A(L)6-J/K/H series is designed for high speed of up to 166MHz and offers fully synchronous
operations referenced to both rising and falling edges of differential clock inputs. While all addresses and control inputs
are latched on the rising edges of the clock, Data, Data strobes and Write data masks inputs are sampled on both rising and falling edges of it. The data paths are internally pipelined and 2-bit prefetched to achieve very high bandwidth.
All input and output voltage levels are compatible with SSTL_2. High speed frequencies, programmable latencies and
burst lengths allow variety of device operation in high performance memory system.
Hynix HYMD532M646A(L)6-J/K/H series incorporates SPD(serial presence detect). Serial presence detect function is
implemented via a serial 2,048-bit EEPROM. The first 128 bytes of serial PD data are programmed by Hynix to identify
DIMM type, capacity and other the information of DIMM and the last 128 bytes are available to the customer.
FEATURES
•
256MB (32M x 64) Unbuffered DDR SO-DIMM
based on 32Mx16 DDR SDRAM
•
Data inputs on DQS centers when write (centered
DQ)
•
JEDEC Standard 200-pin small outline dual in-line
memory module (SO-DIMM)
•
Data strobes synchronized with output data for read
and input data for write
•
2.5V +/- 0.2V VDD and VDDQ Power supply
•
Programmable CAS Latency 2 / 2.5 supported
•
All inputs and outputs are compatible with SSTL_2
interface
•
Programmable Burst Length 2 / 4 / 8 with both
sequential and interleave mode
•
Fully differential clock operations (CK & /CK) with
133/166MHz
•
tRAS Lock-out function supported
•
Internal four bank operations with single pulsed RAS
•
All addresses and control inputs except Data, Data
strobes and Data masks latched on the rising edges
of the clock
•
Auto refresh and self refresh supported
•
8192 refresh cycles / 64ms
•
Data(DQ), Data strobes and Write masks latched on
both rising and falling edges of the clock
ORDERING INFORMATION
Part No.
Power Supply
HYMD532M646A(L)6-H
Interface
Form Pactor
SSTL_2
200pin Unbuffered SO-DIMM
67.6mm x 31.75mm x 1mm
166MHz(*DDR333)
HYMD532M646A(L)6-J
HYMD532M646A(L)6-K
Clock Frequency
VDD=2.5V
VDDQ=2.5V
133MHz(*DDR266A)
133MHz(*DDR266B)
* JEDEC Defined Specifications compliant
This document is a general product description and is subject to change without notice. Hynix Semiconductor does not assume any
responsibility for use of circuits described. No patent licenses are implied.
Rev. 0.4/ Oct. 2004
2
HYMD532M646A(L)6-J/K/H
PIN DESCRIPTION
Pin
Pin Description
Pin
CK0, /CK0, CK1, /CK1
Differential Clock Inputs
VDDQ
Pin Description
DQs Power Supply
CS0
Chip Select Input
VSS
Ground
CKE0
Clock Enable Input
VREF
Reference Power Supply
/RAS, /CAS, /WE
Commend Sets Inputs
VDDSPD
Power Supply for SPD
A0 ~ A12
Address
SA0~SA2
E2PROM Address Inputs
BA0, BA1
Bank Address
SCL
E2PROM Clock
DQ0~DQ63
Data Inputs/Outputs
SDA
E2PROM Data I/O
DQS0~DQS7
Data Strobe Inputs/Outputs
VDDID
VDD Identification Flag
DM0~DM7
Data-in Mask
DU
Do not Use
VDD
Power Supply
NC
No Connection
PIN ASSIGNMENT
Pin
Name
Pin
Name
Pin
Name
Pin
1
VREF
2
VREF
51
VSS
52
3
VSS
4
VSS
53
DQ19
54
Name
Pin
Name
VSS
101
A9
Pin
Name
Pin
Name
Pin
Name
102
A8
151
DQ42
152
DQ46
DQ23
103
VSS
104
VSS
153
DQ43
154
DQ47
5
DQ0
6
DQ4
55
DQ24
56
DQ28
105
A7
106
A6
155
VDD
156
VDD
7
DQ1
8
DQ5
57
VDD
58
VDD
107
A5
108
A4
157
VDD
158
/CK1
9
VDD
10
VDD
59
DQ25
60
DQ29
109
A3
110
A2
159
VSS
160
CK1
11
DQS0
12
DM0
61
DQS3
62
DM3
111
A1
112
A0
161
VSS
162
VSS
13
DQ2
14
DQ6
63
VSS
64
VSS
113
VDD
114
VDD
163
DQ48
164
DQ52
15
VSS
16
VSS
65
DQ26
66
DQ30
115
A10/AP
116
BA1
165
DQ49
166
DQ53
17
DQ3
18
DQ7
67
DQ27
68
DQ31
117
BA0
118
/RAS
167
VDD
168
VDD
19
DQ8
20
DQ12
69
VDD
70
VDD
119
/WE
120
/CAS
169
DQS6
170
DM6
21
VDD
22
VDD
71
NC
72
NC
121
/CS0
122
NC
171
DQ50
172
DQ54
23
DQ9
24
DQ13
73
NC
74
NC
123
DU
124
DU
173
VSS
174
VSS
25
DQS1
26
DM1
75
VSS
76
VSS
125
VSS
126
VSS
175
DQ51
176
DQ55
DQ60
27
VSS
28
VSS
77
NC
78
NC
127
DQ32
128
DQ36
177
DQ56
178
29
DQ10
30
DQ14
79
NC
80
NC
129
DQ33
130
DQ37
179
VDD
180
VDD
31
DQ11
32
DQ15
81
VDD
82
VDD
131
VDD
132
VDD
181
DQ57
182
DQ61
33
VDD
34
VDD
83
NC
84
NC
133
DQS4
134
DM4
183
DQS7
184
DM7
35
CK0
36
VDD
85
DU
86
DU
135
DQ34
136
DQ38
185
VSS
186
VSS
37
/CK0
38
VSS
87
VSS
88
VSS
137
VSS
138
VSS
187
DQ58
188
DQ62
39
VSS
40
VSS
89
NC
90
VSS
139
DQ35
140
DQ39
189
DQ59
190
DQ63
41
DQ16
42
DQ20
91
NC
92
VDD
141
DQ40
142
DQ44
191
VDD
192
VDD
43
DQ17
44
DQ21
93
VDD
94
VDD
143
VDD
144
VDD
193
SDA
194
SA0
45
VDD
46
VDD
95
NC
96
CKE0
145
DQ41
146
DQ45
195
SCL
196
SA1
47
DQS2
48
DM2
97
NC
98
DU
147
DQS5
148
DM5
197
VDDSPD
198
SA2
49
DQ18
50
DQ22
99
A12
100
A11
149
VSS
150
VSS
199
VDDID
200
DU
Rev. 0.4/ Oct. 2004
3
HYMD532M646A(L)6-J/K/H
FUNCTIONAL BLOCK DIAGRAM
/CS0
/CS
DQS1
DM1
DQS0
DM0
LDQS
LDM
I/O 6
I/O 4
I/O 1
I/O 3
I/O 2
I/O 0
I/O 5
I/O 7
UDQS
UDM
I/O 8
I/O 10
I/O 15
I/O 13
I/O 12
I/O 14
I/O 11
I/O 9
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
/CS
DQS5
DM5
D0
DQS4
DM4
LDQS
LDM
I/O 6
I/O 4
I/O 1
I/O 3
I/O 2
I/O 0
I/O 5
I/O 7
UDQS
UDM
I/O 8
I/O 10
I/O 15
I/O 13
I/O 12
I/O 14
I/O 11
I/O 9
DQ40
DQ41
DQ42
DQ43
DQ44
DQ45
DQ46
DQ47
DQ32
DQ33
DQ34
DQ35
DQ36
DQ37
DQ38
DQ39
/CS
DQS3
DM3
DQS2
DM2
LDQS
LDM
I/O 6
I/O 4
I/O 1
I/O 3
I/O 2
I/O 0
I/O 5
I/O 7
UDQS
UDM
I/O 8
I/O 10
I/O 15
I/O 13
I/O 12
I/O 14
I/O 11
I/O 9
DQ24
DQ25
DQ26
DQ27
DQ28
DQ29
DQ30
DQ31
DQ16
DQ17
DQ18
DQ19
DQ20
DQ21
DQ22
DQ23
/CS
DQS7
DM7
D1
DQS6
DM6
Serial PD
SCL
DQ48
DQ49
DQ50
DQ51
DQ52
DQ53
DQ54
DQ55
VDD/VDDQ
SDA
A0
A1
A2
VREF
VSS
SA0
SA1
SA2
BA0-BA1
BA0-BA1 : SDRAMs D0 - D3
A0 - A12
A0 - A12 : SDRAMs D0 - D3
/RAS
/RAS : SDRAMs D0 - D3
/CAS
/CAS : SDRAMs D0 - D3
CKE0
CKE : SDRAMs D0 - D3
/WE
/WE : SDRAMs D0 - D3
Rev. 0.4/ Oct. 2004
LDQS
LDM
I/O 6
I/O 4
I/O 1
I/O 3
I/O 2
I/O 0
I/O 5
I/O 7
UDQS
UDM
I/O 8
I/O 10
I/O 15
I/O 13
I/O 12
I/O 14
I/O 11
I/O 9
DQ56
DQ57
DQ58
DQ59
DQ60
DQ61
DQ62
DQ63
VDDSPD
WP
D2
VDDID
.
.
= = .
. . . =.
..
D3
SPD
D0 - D3
D0 - D3
D0 - D3
Strap:see Note 4
Notes:
DQ wiring may differ from that described in this drawing ;
however DQ/DM/DQS relationship are maintained as shown.
VDDID strap connections;
(for memory device VDD, VDDQ) :
Strap out :(open) : VDD=VDDQ
Strap In (Vss) : VDD= VDDQ
4
HYMD532M646A(L)6-J/K/H
ABSOLUTE MAXIMUM RATINGS
Parameter
Symbol
Rating
Unit
Operating Temperature (Ambient)
TA
0 ~ 70
o
Storage Temperature
TSTG
-55 ~ 125
oC
Voltage on Any Pin relative to VSS
VIN, VOUT
-0.5 ~ 3.6
V
Voltage on VDD relative to VSS
VDD
-0.5 ~ 3.6
V
Voltage on VDDQ relative to VSS
VDDQ
-0.5 ~ 3.6
V
Output Short Circuit Current
IOS
50
mA
Power Dissipation
PD
1.0 x # of Components
W
Soldering Temperature Þ Time
TSOLDER
260 / 10
oC
C
/ Sec
Note : Operation at above absolute maximum rating can adversely affect device reliability
DC OPERATING CONDITIONS (TA=0 to 70 oC, Voltage referenced to VSS= 0V)
Parameter
Symbol
Min
Typ.
Max
Unit
Power Supply Voltage
VDD
2.3
2.5
2.7
V
Power Supply Voltage
VDDQ
2.3
2.5
2.7
V
Input High Voltage
VIH
VREF + 0.15
-
VDDQ + 0.3
V
Input Low Voltage
VIL
-0.3
-
VREF - 0.15
V
Termination Voltage
VTT
VREF - 0.04
VREF
VREF + 0.04
V
Reference Voltage
VREF
1.15
1.25
1.35
V
Note
1
2
3
Note :
1. VDDQ must not exceed the level of VDD.
2. VIL (min) is acceptable -1.5V AC pulse width with < 5ns of duration.
3. The value of VREF is approximately equal to 0.5VDDQ.
AC OPERATING CONDITIONS (TA=0 to 70 oC, Voltage referenced to VSS = 0V)
Parameter
Symbol
Min
Input High (Logic 1) Voltage, DQ, DQS and DM signals
VIH(AC)
VREF + 0.31
Input Low (Logic 0) Voltage, DQ, DQS and DM signals
VIL(AC)
Input Differential Voltage, CK and /CK inputs
VID(AC)
Input Crossing Point Voltage, CK and /CK inputs
VIX(AC)
Max
Unit
Note
V
VREF - 0.31
V
0.7
VDDQ + 0.6
V
1
0.5*VDDQ-0.2
0.5*VDDQ+0.2
V
2
Note :
1. VID is the magnitude of the difference between the input level on CK and the input on /CK.
2. The value of V IX is expected to equal 0.5*V DDQ of the transmitting device and must track variations in the DC level of the same.
Rev. 0.4/ Oct. 2004
5
HYMD532M646A(L)6-J/K/H
AC OPERATING TEST CONDITIONS (TA=0 to 70oC, Voltage referenced to VSS = 0V)
Parameter
Value
Unit
Reference Voltage
VDDQ x 0.5
V
Termination Voltage
VDDQ x 0.5
V
AC Input High Level Voltage (VIH, min)
VREF + 0.31
V
AC Input Low Level Voltage (VIL, max)
VREF - 0.31
V
VREF
V
Output Timing Measurement Reference Level Voltage
VTT
V
Input Signal maximum peak swing
1.5
V
Input minimum Signal Slew Rate
1
V/ns
Termination Resistor (RT)
50
Ω
Series Resistor (RS)
25
Ω
Output Load Capacitance for Access Time Measurement (CL)
30
pF
Input Timing Measurement Reference Level Voltage
Rev. 0.4/ Oct. 2004
6
HYMD532M646A(L)6-J/K/H
CAPACITANCE (TA=25oC, f=100MHz )
Parameter
Pin
Symbol
Min
Max
Unit
Input Capacitance
A0 ~ A12, BA0, BA1
CIN1
31
35
pF
Input Capacitance
/RAS, /CAS, /WE
CIN2
31
35
pF
Input Capacitance
CKE0, CKE1
CIN3
36
40
pF
Input Capacitance
/CS0, /CS1
CIN4
35
39
pF
Input Capacitance
CK0, /CK0, CK1, /CK1
CIN5
20
24
pF
Input Capacitance
DM0 ~ DM7
CIN6
9
11
pF
Data Input / Output Capacitance
DQ0 ~ DQ63, DQS0 ~ DQS7
CIO1
9
11
pF
Note :
1. VDD = min. to max., VDDQ = 2.3V to 2.7V, VODC = VDDQ/2, VOpeak-to-peak = 0.2V
2. Pins not under test are tied to GND.
3. These values are guaranteed by design and are tested on a sample basis only.
OUTPUT LOAD CIRCUIT
V TT
R T=50Ω
Output
Zo=50Ω
V REF
C L=30pF
Rev. 0.4/ Oct. 2004
7
HYMD532M646A(L)6-J/K/H
DC CHARACTERISTICS I (TA=0 to 70oC, Voltage referenced to VSS = 0V)
Parameter
Symbol
Add, CMD, /CS, /CKE
Input Leakage
Current
CK0, /CK0, CK1, /CK1
ILI
CK2, /CK2
Min.
Max
-8
8
-8
8
0
0
Unit
Note
uA
1
Output Leakage Current
ILO
-5
5
uA
2
Output High Voltage
VOH
VTT + 0.76
-
V
IOH = -15.2mA
Output Low Voltage
VOL
-
VTT - 0.76
V
IOL = +15.2mA
Note :
1. VIN = 0 to 3.6V, All other pins are not tested under VIN =0V
2. DOUT is disabled, VOUT=0 to 2.7V
Rev. 0.4/ Oct. 2004
8
HYMD532M646A(L)6-J/K/H
DC CHARACTERISTICS II (TA=0 to 70oC, Voltage referenced to VSS = 0V)
Parameter
Symbol
Speed
Test Condition
Unit Note
-J
-K
-H
560
480
480
mA
Operating Current
IDD0
One bank; Active - Precharge; tRC=tRC(min);
tCK=tCK(min); DQ,DM and DQS inputs changing
twice per clock cycle ; address and control inputs
changing once per clock cycle
Operating Current
IDD1
One bank; Active - Read - Precharge; Burst Length =2;
tRC=tRC(min); tCK=tCK(min); address and control
inputs changing once per clock cycle
720
600
600
mA
40
40
40
mA
Precharge Power
Down Standby Current
IDD2P
All banks idle; Power down mode; CKE=Low, tCK=
tCK(min)
Idle Standby Current
IDD2N
Vin>=Vih(min) or Vin=<Vil(max) for DQ, DQS and DM
140
mA
Idle Standby Current
IDD2F
/CS=High, All banks idle; tCK=tCK(min); CKE= High;
address and control inputs changing once per clock
cycle. VIN=VREF for DQ, DQS and DM
140
mA
Idle Quiet Standby
Current
IDD2Q
/CS>=Vih(min); All banks idle; CKE>=Vih(min);
Addresses and other control inputs stable, Vin=Vref for
DQ, DQS and DM
100
mA
Active Power Down
Standby Current
IDD3P
One bank active ; Power down mode; CKE=Low,
tCK=tCK(min)
48
mA
Active Standby Current
IDD3N
/CS=HIGH; CKE=HIGH; One bank; Active-Precharge;
tRC=tRAS(max); tCK=tCK(min); DQ, DM and DQS
inputs changing twice per clock cycle; Address and
other control inputs changing once per clock cycle
180
160
160
Operating Current
IDD4R
Burst=2; Reads; Continuous burst; One bank active;
Address and control inputs changing once per clock
cycle; tCK=tCK(min); IOUT=0mA
1000
840
840
IDD4W
Burst=2; Writes; Continuous burst; One bank active;
Address and control inputs changing once per clock
cycle; tCK=tCK(min); DQ, DM, and DQS inputs
changing twice per clock cycle
1000
880
880
1120
1040
1040
Operating Current
Auto Refresh Current
IDD5
tRC=tRFC(min) - 8*tCK for DDR200 at 100Mhz,
10*tCK for DDR266A & DDR266B at 133Mhz;
distributed refresh
Self Refresh Current
IDD6
CKE=<0.2V; External clock on; tCK
=tCK(min)
Operating Current Four Bank Operation
Random Read Current
Rev. 0.4/ Oct. 2004
mA
mA
Normal
20
mA
Low Power
10
mA
IDD7
Four bank interleaving with BL=4 Refer to the following
page for detailed test condition
1840
1520
1520
mA
IDD7A
4banks active read with activate every 20ns, AP(Auto
Precharge) read every 20ns, BL=4, tRCD=3, IOUT=0
mA, 100% DQ, DM and DQS inputs changing twice
per clock cycle; 100% addresses changing once per
clock cycle
1840
1520
1520
mA
9
HYMD532M646A(L)6-J/K/H
AC CHARACTERISTICS (AC operating conditions unless otherwise noted)
Parameter
Symbol
-J(DDR333)
-K(DDR266A)
-H(DDR266B)
Min
Max
Min
Max
Min
Max
Unit
Row Cycle Time
tRC
60
-
65
-
70
-
ns
Auto Refresh Row Cycle Time
tRFC
72
-
75
-
80
-
ns
Row Active Time
tRAS
42
70K
45
120K
45
120K
ns
Active to Read with Auto Precharge Delay
tRAP
tRCD or
tRASmin
-
tRCD or
tRASmin
-
tRCD or
tRASmin
-
ns
Row Address to Column Address Delay
tRCD
18
-
20
-
20
-
ns
Row Active to Row Active Delay
tRRD
12
-
15
-
15
-
ns
Column Address to Column Address Delay
tCCD
1
-
1
-
1
-
CK
Row Precharge Time
tRP
18
-
20
-
20
-
ns
Write Recovery Time
tWR
15
-
15
-
15
-
ns
Write to Read Command Delay
tWTR
1
-
1
-
1
-
CK
Auto Precharge Write Recovery+Precharge
Time
tDAL
2+(tRP/
tCK)
-
5
-
(tWR/
tCK)+(tR
P/tCK)
-
CK
6
12
7.5
12
8
12
ns
7.5
12
7.5
12
10
12
ns
System Clock Cycle Time
CL = 2.5
CL = 2
tCK
Note
16
15
Clock High Level Width
tCH
0.45
0.55
0.45
0.55
0.45
0.55
CK
Clock Low Level Width
tCL
0.45
0.55
0.45
0.55
0.45
0.55
CK
Data-Out edge to Clock edge Skew
tAC
-0.7
0.7
-0.75
0.75
-0.75
0.75
ns
DQS-Out edge to Clock edge Skew
tDQSCK
-0.6
0.6
-0.75
0.75
-0.75
0.75
ns
DQS-Out edge to Data-Out edge Skew
tDQSQ
-
0.45
-
0.5
-
0.6
ns
Data-Out hold time from DQS
tQH
tHPmin
-tQHS
-
tHPmin
-tQHS
-
tHPmin
-tQHS
-
ns
1, 10
Clock Half Period
tHP
tCH/L
min
-
tCH/L
min
-
tCH/L
min
-
ns
1,9
tQHS
-
0.55
-
0.75
-
0.75
ns
10
Data Hold Skew Factor
Valid Data Output Window
tDV
tQH-tDQSQ
Data-out high-impedance window from CK, /CK
tHZ
-0.7
0.7
-0.75
Data-out low-impedance window from CK, /CK
tLZ
-0.7
0.7
Input Setup Time (fast slew rate)
tIS
0.75
Input Hold Time (fast slew rate)
tIH
Input Setup Time (slow slew rate)
Input Hold Time (slow slew rate)
Input Pulse Width
Rev. 0.4/ Oct. 2004
tQH-tDQSQ
tQH-tDQSQ
ns
0.75
-0.8
0.8
ns
-0.75
0.75
-0.8
0.8
ns
-
0.9
-
1.1
-
ns
2,3,5,6
0.75
-
0.9
-
1.1
-
ns
2,3,5,6
tIS
0.8
-
1.0
-
1.1
-
ns
2,4,5,6
tIH
0.8
-
1.0
-
1.1
-
ns
2,4,5,6
tIPW
2.2
-
2.2
-
2.5
-
ns
6
10
HYMD532M646A(L)6-J/K/H
AC CHARACTERISTICS (AC operating conditions unless otherwise noted)
Parameter
- continued -
-J(DDR333)
-K(DDR266A)
-H(DDR266B)
Min
Max
Min
Max
Min
Max
Symbol
Unit
Note
Write DQS High Level Width
tDQSH
0.35
-
0.35
-
0.35
-
CK
Write DQS Low Level Width
tDQSL
0.35
-
0.35
-
0.35
-
CK
Clock to First Rising edge of DQS-In
tDQSS
0.75
1.25
0.75
1.25
0.75
1.25
CK
Data-In Setup Time to DQS-In (DQ & DM)
tDS
0.45
-
0.5
-
0.6
-
ns
6,7,
11~13
Data-in Hold Time to DQS-In (DQ & DM)
tDH
0.45
-
0.5
-
0.6
-
ns
6,7,
11~13
DQ & DM Input Pulse Width
tDIPW
1.75
-
1.75
-
2
-
ns
Read DQS Preamble Time
tRPRE
0.9
1.1
0.9
1.1
0.9
1.1
CK
Read DQS Postamble Time
tRPST
0.4
0.6
0.4
0.6
0.4
0.6
CK
Write DQS Preamble Setup Time
tWPRES
0
-
0
-
0
-
CK
Write DQS Preamble Hold Time
tWPREH
0.25
-
0.25
-
0.25
-
CK
Write DQS Postamble Time
tWPST
0.4
0.6
0.4
0.6
0.4
0.6
CK
Mode Register Set Delay
tMRD
2
-
2
-
2
-
CK
Exit Self Refresh to Any Execute Command
tXSC
200
-
200
-
200
-
CK
Average Periodic Refresh Interval
tREFI
-
7.8
-
7.8
-
7.8
us
8
Note :
1.
This calculation accounts for tDQSQ(max), the pulse width distortion of on-chip circuit and jitter.
2.
Data sampled at the rising edges of the clock : A0~A12, BA0~BA1, CKE, /CS, /RAS, /CAS, /WE.
3.
For command/address input slew rate >=1.0V/ns
4.
For command/address input slew rate >=0.5V/ns and <1.0V/ns
This derating table is used to increase tIS/tIH in case where the input slew-rate is below 0.5V/ns.
Input Setup / Hold Slew-rate Derating Table.
Input Setup / Hold Slew-rate
Delta tIS
Delta tIH
V/ns
ps
ps
0.5
0
0
0.4
+50
0
0.3
+100
0
5.
CK, /CK slew rates are >=1.0V/ns
6.
These parameters guarantee device timing, but they are not necessarily tested on each device, and they may be guaranteed by
design or tester correlation
7.
Data latched at both rising and falling edges of Data Strobes(LDQS/UDQS) : DQ, LDM/UDM.
8.
Minimum of 200 cycles of stable input clocks after Self Refresh Exit command, where CKE is held high, is required to complete
Self Refresh Exit and lock the internal DLL circuit of DDR SDRAM.
9.
Min (tCL, tCH) refers to the smaller of the actual clock low time and the actual clock high time as provided to the device (i.e. this
value can be greater than the minimum specification limits for tCL and tCH).
10. tHP = minimum half clock period for any given cycle and is defined by clock high or clock low (tCH, tCL). tQHS consists of
tDQSQmax, the pulse width distortion of on-chip clock circuits, data pin to pin skew and output pattern effects and p-channel to
n-channel variation of the output drivers.
Rev. 0.4/ Oct. 2004
11
HYMD532M646A(L)6-J/K/H
11.This derating table is used to increase tDS/tDH in case where the input slew-rate is below 0.5V/ns.
Input Setup / Hold Slew-rate Derating Table.
Input Setup / Hold Slew-rate
Delta tDS
Delta tDH
V/ns
ps
ps
0.5
0
0
0.4
+75
+75
0.3
+150
+150
12. I/O Setup/Hold Plateau Derating. This derating table is used to increase tDS/tDH in case where the input level is flat below VREF
+/-310mV for a duration of up to 2ns.
I/O Input Level
Delta tDS
Delta tDH
mV
ps
ps
+280
+50
+50
13. I/O Setup/Hold Delta Inverse Slew Rate Derating. This derating table is used to increase tDS/tDH in case where the DQ and DQS
slew rates differ. The Delta Inverse Slew Rate is calculated as (1/SlewRate1)-(1/SlewRate2). For example, if slew rate 1 = 0.5V/ns
and Slew Rate2 = 0.4V/n then the Delta Inverse Slew Rate = -0.5ns/V.
(1/SlewRate1)-(1/SlewRate2)
Delta tDS
Delta tDH
ns/V
ps
ps
0
0
0
+/-0.25
+50
+50
+/- 0.5
+100
+100
14. DQS, DM and DQ input slew rate is specified to prevent double clocking of data and preserve setup and hold times. Signal transi
tions through the DC region must be monotonic.
15. tDAL = (tDPL / tCK ) + (tRP / tCK ). For each of the terms above, if not already an integer, round to the next highest integer. tCK
is equal to the actual system clock cycle time.
Example: For DDR266B at CL=2.5 and tCK = 7.5 ns,
tDAL = (15 ns / 7.5 ns) + (20 ns / 7.5 ns) = (2.00) + (2.67)
Round up each non-integer to the next highest integer: = (2) + (3), tDAL = 5 clock
16. For the parts which do not has internal RAS lockout circuit, Active to Read with Auto precharge delay should be
tRAS - BL/2 x tCK.
Rev. 0.4/ Oct. 2004
12
HYMD532M646A(L)6-J/K/H
SIMPLIFIED COMMAND TRUTH TABLE
A10/
AP
Command
CKEn-1
CKEn
/CS
/RAS
/CAS
/WE
Extended Mode Register Set
H
X
L
L
L
L
OP code
1,2
Mode Register Set
H
X
L
L
L
L
OP code
1,2
H
X
X
X
H
X
X
1
L
H
H
H
Device Deselect
No Operation
Bank Active
H
X
L
L
H
H
H
X
L
H
L
H
ADDR
RA
Read
BA
V
L
CA
Read with Autoprecharge
1
1,3
L
H
X
L
H
L
L
CA
Write with Autoprecharge
1
V
H
Precharge All Banks
H
X
L
L
H
L
Precharge selected Bank
1
V
H
Write
Note
1,4
H
X
1,5
L
V
1
X
Read Burst Stop
H
X
L
H
H
L
X
1
Auto Refresh
H
H
L
L
L
H
X
1
Entry
H
L
L
L
L
H
H
X
X
X
Exit
L
H
L
H
H
H
H
X
X
X
L
H
H
H
Self Refresh
Precharge
Power Down
Mode
Active Power
Down Mode
(Clock Suspend)
Entry
H
1
X
1
1
L
1
X
Exit
Entry
Exit
L
H
L
H
X
X
X
1
L
H
H
H
1
H
X
X
X
1
L
V
V
V
H
L
H
X
X
1
1
Note :
1. LDM/UDM states are Don’t Care. Refer to below Write Mask Truth Table.
2. OP Code(Operand Code) consists of A0~A12 and BA0~BA1 used for Mode Registering duing Extended MRS or MRS.
Before entering Mode Register Set mode, all banks must be in a precharge state and MRS command can be issued after tRP
period from Prechagre command.
3. If a Read with Autoprecharge command is detected by memory component in CK(n), then there will be no command presented
to activated bank until CK(n+BL/2+tRP).
4. If a Write with Autoprecharge command is detected by memory compoment in CK(n), then there will be no command presented
to activated bank until CK(n+BL/2+1+tDPL+tRP). Last Data-In to Prechage delay(tDPL) which is also called Write Recovery Time
(tWR) is needed to guarantee that the last data has been completely written.
5. If A10/AP is High when Row Precharge command being issued, BA0/BA1 are ignored and all banks are selected to be
precharged.
Rev. 0.4/ Oct. 2004
13
HYMD532M646A(L)6-J/K/H
PACKAGE DIMENSIONS
Front
67.60 mm
2.00 mm
Component
Keepout
Area
2.00 mm
31.75 mm
20.00 mm
Side
1
39
41
199
Back
2.0 mm
2
40
42
3.8mm
MAX.
2.0 mm
200
(Front)
1.1mm
MAX.
# The location and number of additional
device can be different from real product
Rev. 0.4/ Oct. 2004
14
SERIAL PRESENCE DETECT
SPD SPECIFICATION
(32Mx64 Unbuffered DDR SO-DIMM)
Rev. 0.4/ Oct. 2004
15
HYMD532M646A(L)6-J/K/H
SERIAL PRESENCE DETECT
Byte#
0
Function Description
Bin Sort : J(DDR333@CL=2.5), K(DDR266A@CL=2), H(DDR266B@CL=2.5)
Function Supported
J
K
Number of Bytes written into serial memory at module
manufacturer
1
Total number of Bytes in SPD device
2
Fundamental memory type
3
4
Hexa Value
H
J
K
128 Bytes
80h
256 Bytes
08h
H
Note
DDR SDRAM
07h
Number of row address on this assembly
13
0Dh
1
Number of column address on this assembly
10
0Ah
1
5
Number of physical banks on DIMM
1Bank
01h
6
Module data width
64 Bits
40h
-
00h
7
Module data width (continued)
8
Module voltage Interface levels(VDDQ)
9
DDR SDRAM cycle time at CAS Latency=2.5(tCK)
10
DDR SDRAM access time from clock at CL=2.5 (tAC)
11
Module configuration type
12
Refresh rate and type
13
14
15
Minimum clock delay for back-to-back random column
address(tCCD)
16
Burst lengths supported
17
Number of banks on each DDR SDRAM
18
CAS latency supported
19
20
21
DDR SDRAM module attributes
22
DDR SDRAM device attributes : General
SSTL 2.5V
04h
6.0ns
7.5ns
7.5ns
60h
75h
75h
2
+/-0.7ns
+/-0.75ns
+/-0.75ns
70h
75h
75h
2
Non-ECC
00h
7.8us & Self refresh
82h
Primary DDR SDRAM width
x16
10h
Error checking DDR SDRAM data width
N/A
00h
1 CLK
01h
2,4,8
0Eh
4 Banks
04h
2, 2.5
0Ch
CS latency
0
01h
WE latency
1
02h
Differential Clock Input
20h
+/-0.2Voltage tolerance,
Concurrent Auto Precharge
tRAS Lock Out
C0h
23
DDR SDRAM cycle time at CL=2.0(tCK)
24
DDR SDRAM access time from clock at CL=2.0(tAC)
7.5ns
7.5ns
10ns
75h
75h
A0h
+/-0.7ns
+/-0.75ns
+/-0.75ns
70h
75h
25
DDR SDRAM cycle time at CL=1.5(tCK)
75h
26
DDR SDRAM access time from clock at CL=1.5(tAC)
27
Minimum row precharge time(tRP)
18ns
20ns
20ns
48h
50h
50h
28
Minimum row activate to row active delay(tRRD)
12ns
15ns
15ns
30h
3Ch
3Ch
29
Minimum RAS to CAS delay(tRCD)
18ns
20ns
20ns
48h
50h
50h
30
Minimum active to precharge time(tRAS)
42ns
45ns
45ns
2Ah
2Dh
2Dh
-
00h
-
00h
31
Module row density
32
Command and address signal input setup time(tIS)
0.75ns
256MB
0.9ns
0.9ns
75h
90h
90h
33
Command and address signal input hold time(tIH)
0.75ns
0.9ns
0.9ns
75h
90h
90h
34
Data signal input setup time(tDS)
0.45ns
0.5ns
0.5ns
45h
50h
50h
35
Data signal input hold time(tDH)
0.45ns
0.5ns
0.5ns
45h
50h
50h
36~40 Reserved for VCSDRAM
40h
Undefined
00h
41
Minimum active / auto-refresh Time (tRC)
60ns
65ns
65ns
3Ch
41h
41h
42
Minimum auto-refresh to active / auto-refresh
command period (tRFC)
72ns
75ns
75ns
48h
4Bh
4Bh
43
Maximum cycle time (tCK max)
12ns
12ns
12ns
30h
30h
30h
44
Maximum DQS-DQ skew time (tDQSQ)
0.45ns
0.5ns
0.5ns
2Dh
32h
32h
45
Maximum read data hold skew factor (tQHS)
0.55ns
0.75ns
0.75ns
55h
75h
75h
46~61 Superset Information(may be used in future)
62
SPD Revision code
63
Checksum for Bytes 0~62
Rev. 0.4/ Oct. 2004
Undefined
00h
Initial release
00h
-
08h
BFh
EAh
16
HYMD532M646A(L)6-J/K/H
SERIAL PRESENCE DETECT(continued)
Byte #
64
65~71
Function Description
Function Supported
J
Manufacturer JEDEC ID Code
K
H
Hexa Value
J
K
Hynix JEDEC ID
ADh
-
00h
Hynix(Korea Area)
HSA(United States Area)
HSE(Europe Area)
HSJ(Japan Area)
Singapore
Asia Area
0*h
1*h
2*h
3*h
4*h
5*h
--------- Manufacturer JEDEC ID Code
72
Manufacturing location
73
Manufacture part number(Hynix Memory Module)
H
48h
74
-------- Manufacture part number(Hynix Memory Module)
Y
59h
75
-------- Manufacture part number(Hynix Memory Module)
M
4Dh
76
Manufacture part number (DDR SDRAM)
D
44h
77
Manufacture part number(Memory density)
5
35h
78
Manufacture part number(Module Depth)
3
33h
79
------- Manufacture part number(Module Depth)
2
32h
80
Manufacture part number(Module type)
M
4Dh
81
Manufacture part number(Data width)
6
36h
82
-------Manufacture part number(Data width)
4
34h
83
Manufacture part number(Refresh, # of Bank.)
6(8K refresh,4Bank)
36h
84
Manufacture part number(Component Generation)
A
41h
85
Manufacture part number(Component configuration)
6
36h
86
Manufacture part number(Hyphen)
‘-’
2Dh
87
Manufacture part number(Minimum cycle time)
88~90
J
Manufacture part number(T.B.D)
K
H
4Bh
48h
-
20h
Blank
20h
H
Note
6
4Ch
91
Manufacture revision code(for Component)
92
Manufacture revision code (for PCB)
-
-
93
Manufacturing date(Year)
-
-
94
Manufacturing date(Week)
-
-
3
Module serial number
-
-
4
95~98
3
99~127
Manufacturer specific data (may be used in future)
Undefined
00h
5
128~255
Open for customer use
Undefined
00h
5
Note :
1. The bank address is excluded
2. This value is based on the component specification
3. These bytes are programmed by code of date week & date year
4. These bytes apply to Hynix’s own Module Serial Number System
5. These bytes undefined and coded as ‘00h’
6. Refer to Hynix Web Site
Byte 85~86, Low power part
Byte#
85
86
Function Description
Manufacture part number(Low power part)
Manufacture part number(Component Configuration)
Rev. 0.4/ Oct. 2004
Function Supported
J
K
L
6
H
Hexa Value
J
K
H
Note
4Ch
36h
17