EVERLIGHT ELECTRONICS CO.,LTD. Technical Data Sheet Chip LED with Bi-Color(Multi-Color) 15-22SDRVGC/S530-A2/TR8 Features ․Package in 8mm tape on 7〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Multi-color type. ․Pb-free. Descriptions ․The 15-22 SMD Taping is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. ․Besides, lightweight makes them ideal for miniature applications. etc. Applications ․Automotive: backlighting in dashboard and switch. ․Telecommunication: indicator and backlighting in telephone and fax. ․Flat backlight for LCD, switch and symbol. ․General use. Device Selection Guide Chip Type Material Emitted Color SDR AlGaInP Super Deep-Red Lens Color Water Clear VG GaP Green Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-152 Prepared date:08-04-2004 Rev. 1.0 Page: 1 of 11 Prepared by : Kenny Wang EVERLIGHT ELECTRONICS CO.,LTD. 15-22SDRVGC/S530-A2/TR8 Package Outline Dimensions RED - + - + Notes: Tolerances Unless Dimension ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-152 Prepared date: 08-04-2004 Rev. 1.0 2Page: 2 of 11 Prepared by : Kenny Wang EVERLIGHT ELECTRONICS CO.,LTD. 15-22SDRVGC/S530-A2/TR8 Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Unit Reverse Voltage VR 5 V Forward Current IF Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +90 ℃ Soldering Temperature Tsol Electrostatic Discharge ESD Power Dissipation Pd Peak Forward Current SDR:25 VG:30 second) 2000 SDR:60 VG:100 SDR:60 IFP (Duty 1/10 @1KHz) 260 (for 5 VG:60 mA ℃ V mW mA Electro-Optical Characteristics (Ta=25℃) Parameter Luminous Intensity Viewing Angle Symbol Min. Typ. Iv SDR: 15.0 26.0 VG: 7.00 ----- 13.0 140 ----- 650 570 2θ1/2 λp SDR Peak Wavelength VG λd SDR ----- VG ----- Dominant Wavelength Spectrum Radiation Bandwidth Forward Voltage ----VG SDR ----- VG Reverse Current IR Unit ------ mcd ----- deg ----- nm ----- nm ----- 30 2.0 2.1 ----- Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-152 Prepared date: 08-04-2004 Condition IF=20mA ----- 20 △λ SDR VF 639 571 Max. ----- nm 2.4 2.4 V 10 μA Rev. 1.0 VR=5V 2Page: 3 of 11 Prepared by : Kenny Wang EVERLIGHT ELECTRONICS CO.,LTD. 15-22SDRVGC/S530-A2/TR8 Typical Electro-Optical Characteristics Curves SDR Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-152 Prepared date: 08-04-2004 Rev. 1.0 2Page: 4 of 11 Prepared by : Kenny Wang EVERLIGHT ELECTRONICS CO.,LTD. 15-22SDRVGC/S530-A2/TR8 Typical Electro-Optical Characteristics Curves VG Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-152 Prepared date: 08-04-2004 Rev. 1.0 2Page: 5 of 11 Prepared by : Kenny Wang EVERLIGHT ELECTRONICS CO.,LTD. 15-22SDRVGC/S530-A2/TR8 Label explanation CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank REF: Forward Voltage Rank Reel Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-152 Prepared date: 08-04-2004 Rev. 1.0 2Page: 6 of 11 Prepared by : Kenny Wang EVERLIGHT ELECTRONICS CO.,LTD. 15-22SDRVGC/S530-A2/TR8 Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Moisture Resistant Packaging Label Aluminum moistue-proof bag Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-152 Prepared date: 08-04-2004 Desiccant Rev. 1.0 Label 2Page: 7 of 11 Prepared by : Kenny Wang EVERLIGHT ELECTRONICS CO.,LTD. 15-22SDRVGC/S530-A2/TR8 Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% Test Sample Hours/Cycles Size No. Items Test Condition 1 Reflow Soldering Temp. : 260℃±5℃ 5sec. 6 Min. 22 PCS. 0/1 Temperature Cycle H : +100℃ 15min ∫ 5 min L : -40℃ 15min 300 Cycles 22 PCS. 0/1 Thermal Shock H : +100℃ 5min ∫ 10 sec L : -10℃ 5min 300 Cycles 22 PCS. 0/1 Temp. : 100℃ 1000 Hrs. 22 PCS. 0/1 Temp. : -40℃ 1000 Hrs. 22 PCS. 0/1 2 3 4 5 High Temperature Storage Low Temperature Storage Ac/Re 6 DC Operating Life IF = 20 mA 1000 Hrs. 22 PCS. 0/1 7 High Temperature / High Humidity 85℃/ 85% RH 1000 Hrs. 22 PCS. 0/1 Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-152 Prepared date: 08-04-2004 Rev. 1.0 2Page: 8 of 11 Prepared by : Kenny Wang EVERLIGHT ELECTRONICS CO.,LTD. 15-22SDRVGC/S530-A2/TR8 Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Lead solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-152 Prepared date: 08-04-2004 Rev. 1.0 2Page: 9 of 11 Prepared by : Kenny Wang EVERLIGHT ELECTRONICS CO.,LTD. 15-22SDRVGC/S530-A2/TR8 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 280℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-152 Prepared date: 08-04-2004 Rev. 1.0 2Page: 10 of 11 Prepared by : Kenny Wang