• 1N4099-1 THRU 1N4135-1 AVAILABLE IN JAN, JANTX, JANTXV AND JANS PER MIL-PRF-19500/435 1N4099 thru 1N4135 and 1N4099-1 thru 1N4135-1 • LOW CURRENT OPERATION AT 250 µ A • LOW REVERSE LEAKAGE AND LOW NOISE CHARACTERISTICS • METALLURGICALLY BONDED MAXIMUM RATINGS Junction and Storage Temperature: -65°C to +175°C DC Power Dissipation: 500mW @ +50°C Power Derating: 4 mW / °C above +50°C Forward Voltage at 200 mA: 1.1 Volts maximum ELECTRICAL CHARACTERISTICS @ 25°C, unless otherwise specified. JEDEC TYPE NUMBER NOMINAL ZENER VOLTAGE VZ @ lZT (Note 1) ZENER TEST CURRENT IZT MAXIMUM ZENER IMPEDANCE ZZT (Note 2) MAXIMUM REVERSE LEAKAGE CURRENT lR @ VR √ Hz µA OHMS 6.8 7.5 8.2 250 250 250 200 200 200 10 10 1.0 5.17 5.70 6.24 40 40 40 56 51 46 1N4102 1N4103 1N4104 8.7 9.1 10 250 250 250 200 200 200 1.0 1.0 1.0 6.61 6.92 7.60 40 40 40 44 42 38 1N4105 1N4106 1N4107 11 12 13 250 250 250 200 200 200 .05 .05 .05 8.44 9.12 9.87 40 40 40 35 32 29 1N4108 1N4109 1N4110 14 15 16 250 250 250 200 100 100 .05 .05 .05 10.65 11.40 12.15 40 40 40 27 25 24 1N4111 1N4112 1N4113 17 18 19 250 250 250 100 100 150 .05 .05 .05 12.92 13.67 14.44 40 40 40 22 21 20 1N4114 1N4115 1N4116 20 22 24 250 250 250 150 150 150 .01 .01 .01 15.20 16.72 18.25 40 40 40 19 17 16 1N4117 1N4118 1N4119 25 27 28 250 250 250 150 150 200 .01 .01 .01 19.00 20.46 21.28 40 40 40 15 14 14 1N4120 1N4121 1N4122 30 33 36 250 250 250 200 200 200 .01 .01 .01 22.80 25.08 27.38 40 40 40 13 12 11 1N4123 1N4124 1N4125 39 43 47 250 250 250 200 250 250 .01 .01 .01 29.65 32.65 35.75 40 40 40 9.8 8.9 8.1 1N4126 1N4127 1N4128 51 56 60 250 250 250 300 300 400 .01 .01 .01 38.76 42.60 45.60 40 40 40 7.5 6.7 6.4 1N4129 1N4130 1N4131 62 68 75 250 250 250 500 700 700 .01 .01 .01 47.10 51.68 57.00 40 40 40 6.1 5.6 5.1 1N4132 1N4133 1N4134 1N4135 82 87 91 100 250 250 250 250 800 1000 1200 1500 .01 .01 .01 .01 62.32 66.12 69.16 76.00 40 40 40 40 4.6 4.4 4.2 3.8 NOTE 1 NOTE 2 VOLTS µ V/ MAXIMUM ZENER CURRENT lZM 1N4099 1N4100 1N4101 VOLTS µA MAXIMUM NOISE DENSITY ND @ lZT mA The JEDEC type numbers shown above have a Zener voltage tolerance of + 5% of the nominal Zener voltage. Vz is measured with the device junction in thermal equilibrium at an ambient temperature of 25°C + 3°C. A “C” suffix denotes a + 2% tolerance and a “D” suffix denotes a + 1% tolerance. Zener impedance is derived by superimposing on lZT, A 60 Hz rms a.c. current equal to 10% of lZT (25 µ A a.c.). FIGURE 1 DESIGN DATA CASE: Hermetically sealed glass case. DO – 35 outline. LEAD MATERIAL: Copper clad steel. LEAD FINISH: Tin / Lead THERMAL RESISTANCE: (ROJEC): 250 °C/W maximum at L = .375 inch THERMAL IMPEDANCE: (ZOJX): 35 °C/W maximum POLARITY: Diode to be operated with the banded (cathode) end positive. MOUNTING POSITION: ANY. 6 LAKE STREET, LAWRENCE, MASSACHUSETTS 01841 PHONE (978) 620-2600 FAX (978) 689-0803 WEBSITE: http://www.microsemi.com 33 1N4099 thru 1N4135 INCLUDING -1 VERSIONS 0JL, Junction to Lead Thermal Resistance (°C/W) 400 300 200 100 0 0.2 0.4 0.6 0.8 1.0 L, lead Length to Heat Sink (INCHES) FIGURE 2 TYPICAL THERMAL RESISTANCE 1000 500 400 300 ZENER IMPEDANCE ZZT (OHMS) 200 100 50 40 30 20 10 5 4 3 2 1 .1 .2 .5 1 2 5 10 20 50 OPERATING CURRENT IZT (mA) FIGURE 3 ZENER IMPEDANCE VS. OPERATING CURRENT 34 100