ISO 9001 CERTIFIED BY DSCC
M.S.KENNEDY CORP.
0032
HIGH SPEED, FET INPUT
DIFFERENTIAL OP-AMP
4707 Dey Road Liverpool, N.Y. 13088
(315) 701-6751
MIL-PRF-38534 CERTIFIED
FEATURES:
Fast Slew Rate - 650 V/µS Typ.
FET Input
Wide Bandwidth
Electrically Isolated Case
Industry Wide Pin Compatible 0032 Upgrade
DSCC SMD 5962-80013
DESCRIPTION:
The MSK 0032 is a high speed, FET input, differential amplifier designed to replace the popular LH0032 and
TP0032. Since the MSK 0032 requires less compensation than the LH0032, it exhibits wider bandwidth and greater
stability. The MSK 0032 can be used as a direct replacement in current designs using the LH0032 or TP0032 with no
changes to compensation schemes. High frequency signal transfer circuits such as video amplifiers, high speed
integrators and comparators are just a few of the applications that the MSK 0032 is well suited for.
EQUIVALENT SCHEMATIC
TYPICAL APPLICATIONS
Video Amplifiers
Comparator Circuits
High Speed Integrators
PIN-OUT INFORMATION
1
2
3
4
5
6
No Connection
Output Compensation
Compensation/Balance
Compensation/Balance
Inverting Input
Non-Inverting Input
1
7
8
9
10
11
12
No Connection
No Connection
No Connection
Negative Power Supply
Output
Positive Power Supply
Rev.B 7/00
ABSOLUTE MAXIMUM RATINGS
±VCC
IOUT
VIN
TC
±18V
Supply Voltage
±40mA
Output Current
±30V
Differential Input Voltage
Case Operating Temperature Range
-55°C to +125°C
(MSK 0032B)
-40°C to +85°C
(MSK 0032)
200°C/W
Thermal Resistance
Junction to Case
Output Devices Only
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
RTH
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
TST
TLD
Storage Temperature Range -65°C to +150°C
Lead Temperature Range
300°C
(10 Seconds)
Junction Temperature
175°C
○
○
TJ
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
ELECTRICAL SPECIFICATIONS
Parameter
○
○
±Vcc=±15V Unless Otherwise Specified
MSK 0032B
Group A
Test Conditions
MSK 0032
Subgroup
Min.
Typ.
Max.
Min.
Typ.
Max.
Units
-
±10
±15
±18
-
±15
±18
V
1
-
±15
±20
-
±15
±22
mA
2,3
-
±18
±25
-
-
-
mA
Bal.Pins=N/C VIN=0V AV=-10V/V
1
-
±0.5
±5
-
±1
±7
mV
Input Offset Voltage Drift
Bal.Pins=N/C VIN=0V
2,3
-
±10
±50
-
-
-
µV/°C
Input Offset Adjust
RPOT=10KΩ To +VCC
1,2,3
Adjust to Zero
mV
Input Bias Current
VCM=0V
1
-
±10
±100
-
±25
±300
pA
Either Input
2,3
-
±0.2
±50
-
-
-
nA
Input Offset Current
VCM=0V
1
-
10
25
-
20
100
pA
2,3
-
0.1
25
-
-
Input Impedance 2
F=DC
-
-
10 12
-
-
∆ VCC=±15V
-
50
70
-
F=DC VCM=±10V
-
50
80
F=10Hz To 1MHz
-
-
F=1KHz
-
-
Output Voltage Swing
RL=1KΩ
4
Output Current
RL=1KΩ
RL=1KΩ 10V step
Settling Time to 0.1% 1
Unity Gain Bandwidth 2
STATIC
Supply Voltage Range 2 7
VIN=0V
Quiescent Current
INPUT
Input Offset Voltage
Adjust to Zero
-
nA
10 12
-
Ω
45
70
-
dB
-
45
80
-
dB
1.5
-
-
1.5
-
µVrms
40
-
-
40
-
nV√Hz
±10
±12
-
±10
±12
-
V
4
±10
±20
-
±10
±20
-
mA
4
-
0.1
0.5
-
0.1
0.5
µS
RL=1KΩ 10V step
4
-
300
-
-
300
-
nS
AV=+1
-
-
25
-
-
25
-
MHz
VOUT=±10V RL=1KΩ
4
350
650
-
350
650
-
V/µS
VOUT=±10V F=100Hz
4
70
-
-
70
-
-
dB
Small Signal Rise Time
AV = +1 RL = 1KΩ
4
-
10
20
-
10
20
nS
Small Signal Delay Time
VIN = 1V RL = 1KΩ
4
-
12
25
-
12
25
nS
Power Supply Rejection Ratio 2
Common Mode Rejection Ratio
Input Noise Voltage 2
Equivalent Input Noise 2
2
OUTPUT
Settling Time to 1%
1
TRANSFER CHARACTERISTICS
Slew Rate Limit
Open Loop Voltage Gain
NOTES:
1
2
3
4
5
6
AV=-1, measured in false summing junction circuit.
Devices shall be capable of meeting the parameter, but need not be tested. Typical parameters are for reference only.
Industrial grade devices shall be tested to subgroups 1 and 4 unless otherwise specified.
Military grade devices ('B' suffix) shall be 100% tested to subgroups 1,2,3 and 4.
Subgroup 5 and 6 testing available upon request.
Subgroup 1,4
TA=TC=+25°C
Subgroup 2,5
TA=TC=+125°C
Subgroup 3,6
TA=TC=-55°C
7 Electrical specifications are derated for power supply voltages other than ±15VDC.
2
Rev.B 7/00
APPLICATION NOTES
HEAT SINKING
COMPENSATION
Since the case of the MSK 0032 only runs approximately
40°C hotter than the ambient temperature, a heat sink is generally not necessary. However, in applications where it is critical to minimize input bias current, a heat sink may be used.The
case of the MSK 0032 is isolated from the internal circuitry so
the heat sink may be attached directly to the case. The heat
sink may however create enough parasitic capacitance at the
pins to necessitate adjusting the amount of compensation used.
When replacing an LH0032 or TP0032 with an MSK 0032,
no changes in compensation need be made. The MSK 0032
will demonstrate greater loop stability than the LH0032 and
loop stability very similar to the TP0032. As with any operational amplifier, a feedback capacitor in the range of 2-10pF is
recommended to compensate for the effect of the R-C time
constant created by the input capacitance of the op-amp and
the feedback and input resistors in an inverting configuration.
See Figure 3 and Figure 4 for recommended compensation
schemes for non-inverting configurations.
INPUT OFFSET VOLTAGE NULL
Figure 3
Figure 1
The input offset voltage of the MSK 0032 is typically less
than ±0.5mV. If it is necessary to null the offset to zero or
some value other than zero, the above circuit is recommended.
Typical offset adjust range is 25mV.
Figure 4
POWER SUPPLY BYPASSING
Both the negative and the positive power supplies must be
effectively decoupled with a high and low frequency bypass
circuit to avoid power supply induced oscillation. An effective
decoupling scheme consists of a 0.1 microfarad ceramic capacitor in parallel with a 4.7 microfarad tantalum capacitor from
each power supply pin to ground.
Figure 2
Output Short Circuit Protection
3
Rev.B 7/00
TYPICAL PERFORMANCE CURVES
4
Rev.B 7/00
MECHANICAL SPECIFICATIONS
TO-8 BOTTOM VIEW
ALL DIMENSIONS ARE ±0.010 INCHES UNLESS OTHERWISE LABELED
ORDERING INFORMATION
Part
Number
Screening Level
MSK0032
Industrial
MSK0032B
Military-Mil-PRF-38534
5962-80013
DSCC-SMD
M.S. Kennedy Corp.
4707 Dey Road, Liverpool, New York 13088
Phone (315) 701-6751
FAX (315) 701-6752
www.mskennedy.com
The information contained herein is believed to be accurate at the time of printing. MSK reserves the right to make
changes to its products or specifications without notice, however, and assumes no liability for the use of its products.
5
Rev.B 7/00