MICROSEMI LXM1623-05-61

PanelMatch™
I N T E G R A T E D
LXM1623-05-6x
5V Dual 6W Programmable CCFL Inverter Module
P R O D U C T S
P RODUCTION D ATASHEET
KEY FEATURES
DESCRIPTION
The resultant “burst drive” that
energizes the lamp was designed
specifically to ensure that no premature
lamp degradation occurs, while allowing
significant power savings at lower dim
levels.
The modules convert DC voltage from
the system battery or AC adapter directly
to high frequency, high-voltage waves
required to ignite and operate CCFL
lamps. A 12V input inverter is also
available (LXM1623-12-6x), as well as
4W versions (LXM1623-xx-4x) for
driving smaller lower voltage panels.
The modules design is based on
Microsemi’s new LX1689 backlight
controller, which provides a number of
cost and performance advantages due to
the controller’s high level of integration.
Other benefits of this new topology
are stable fixed-frequency operation,
secondary-side strike-voltage regulation
and both open/shorted lamp protection
with fault timeout.
IMPORTANT: For the most current data, consult MICROSEMI’s website: http://www.microsemi.com
Protected By U.S. Patents: 5,923,129; 5,930,121; 6,198,234; Patents Pending
ƒ Externally Programmable
Maximum Output Current
ƒ Easy to Use Brightness Control
ƒ RangeMAX Wide Range
Dimming
ƒ Output Open/Short-Circuit
Protection and Automatic StrikeVoltage Regulation and Timeout
ƒ Fixed Frequency Operation
ƒ Rated From -20 to 70°C
ƒ UL60950 E175910
APPLICATIONS
WWW . Microsemi .C OM
The LXM1623-05-6x is a Dual 6W
Output Direct Drive™ CCFL (Cold
Cathode Fluorescent Lamp) Inverter
Module specifically designed for driving
LCD backlight lamps. It is ideal for
driving typical 10.4” to 15” TFT panels.
LXM1623 modules provide the
designer with a vastly superior display
brightness range. This brightness range is
achievable with virtually any LCD display.
The modules are available with a
dimming input that permits brightness
control from either a DC voltage source or
a PWM signal or external Potentiometer.
The maximum output current is externally
programmable over a range of 5 to 8mA in
1mA steps to allow the inverter to properly
match to a wide array of LCD panel lamp
current specifications.
RangeMAX
Digital
Dimming
Technique provides flicker-free brightness
control in any wide range typically (50:1+)
dimming application.
ƒ High Brightness Displays
ƒ Portable Instrumentation
ƒ Desktop Displays
ƒ Industrial Display Controls
BENEFITS
ƒ Smooth, Flicker Free 2%100% Full-Range Brightness
Control
ƒ Programmable output current
allows inverter to mate with a
wide variety of LCD panel’s
specifications
ƒ Output Open Circuit Voltage
Regulation Minimizes Corona
Discharge For High Reliability
PRODUCT HIGHLIGHT
U N I V E R S A L D I M M IN G I N P U T
"P W M ", V DC,
P O T E N T IO M E T E R
PW M
S ig n a l
1
3
P o te n tio m e te r
2
2
D C V o lta g e
S o u rc e
OR
W
1
S E L E C T A B L E M A X IM U M O U T P U T C U R R E N T 5 M A
TO 8M A RMS
PACKAGE ORDER INFO
PART NUMBER
LXM1623-05-61
LXM1623-05-62
LXM1623-05-63
Copyright © 2002
Rev. 1.0b, 2005-01-17
OUTPUT CONNECTOR
JST SM02(8.0)B-BHS-1-TB or Yeon Ho 20015WR-05A00
JST SM02B-BHSS-1-TB or Yeon Ho 35001WR-02A00
Honda QZ-19-A3MYL #02
INVERTER MATES DIRECTLY
TO PANEL CONNECTORS
JST BHR-03VS-1
JST BHSR-02VS-1
Honda QZ-19-3F01
Microsemi
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 1
LXM1623-05-6X
3
W
PanelMatch™
I N T E G R A T E D
LXM1623-05-6x
5V Dual 6W Programmable CCFL Inverter Module
P R O D U C T S
P RODUCTION D ATASHEET
Input Signal Voltage (VIN1)....................................................................................................................................-0.3V to 6.5V
Input Power ....................................................................................................................................................................... 15W
Output Voltage, no load ............................................................................................................ Internally Limited to 1800VRMS
Output Current (each output) ......................................................................................................9.5mARMS (Internally Limited)
Output Power (each output) ............................................................................................................................................. 6.0W
Input Signal Voltage ( SLEEP Input) ....................................................................................................................-0.3V to 5.5V
Input Signal Voltage (BRITE) ...............................................................................................................................-0.3V to 5.5V
Ambient Operating Temperature, zero airflow.....................................................................................................-20°C to 70°C
Operating Relative Humidity, non-condensing ................................................................................................................ ≤ 90%
Storage Temperature Range...............................................................................................................................-40°C to 85°C
Note 1: Exceeding these ratings could cause damage to the device. All voltages are with respect to Ground. Currents are positive into, negative out of specified
terminal.
WWW . Microsemi .C OM
ABSOLUTE MAXIMUM RATINGS (NOTE 1)
RECOMMENDED OPERATING CONDITIONS (R.C.)
This module has been designed to operate over a wide range of input and output conditions. However, best efficiency and performance
will be obtained if the module is operated under the condition listed in the ‘R.C.’ column. Min. and Max. columns indicate values beyond
which the inverter, although operational, will not function optimally.
Parameter
Symbol
Input Supply Voltage Range (Fully Regulated
Lamp Current)
Input Supply Voltage Range (Functional)
Output Power (each output)
Linear BRITE Control Input Voltage Range
Lamp Operating Voltage
Lamp Current (Full Brightness)
Operating Ambient Temperature Range
VIN1
PO
VBRT_ADJ
VLAMP
IOLAMP
TA
Recommended Operating Conditions
Min
R.C.
Max
4.75
5
5.25
4.5
5
5.5
5.5
6.0
2.0
720
8†
70
0.5
480
5
-20
600
Units
V
W
V
VRMS
mARMS
°C
†At input voltages below 5V the inverter may not be able to output the full 8mARMS in all configurations
ELECTRICAL CHARACTERISTICS
Unless otherwise specified, the following specifications apply over the recommended operating condition and ambient temperature of
25°C except where otherwise noted.
Parameter
`
Symbol
Test Conditions
LXM1623-05-6x
Min
Typ
Max
Units
OUTPUT PIN CHARACTERISTICS
IL(MAX)
Full Bright Lamp Current (each output)
IL(MAX)
Full Bright Lamp Current (each output)
IL(MAX)
Full Bright Lamp Current (each output)
IL(MAX)
Output Current Lamp to Lamp
Deviation
ILL%DEV
Min. Average Lamp Current
(each output)
Lamp Start Voltage
Operating Frequency
Burst Frequency
Copyright © 2002
Rev. 1.0b, 2005-01-17
IL(MIN)
VLS
fO
fBURST
VBRT_ADJ > 2.0VDC, SLEEP > 2.0V, VIN1 = 5VDC
ISET1 = Ground, ISET2 = Ground
VBRT_ADJ > 2.0VDC, SLEEP > 2.0V, VIN1 = 5VDC
ISET1 = Ground, ISET2 = Open
VBRT_ADJ > 2.0VDC, SLEEP > 2.0V, VIN1 = 5VDC
ISET1 = Open, ISET2 = Ground
VBRT_ADJ > 2.0VDC, SLEEP > 2.0V, VIN1 = 5VDC
ISET1 = Open, ISET2 = Open
VBRT_ADJ > 2.0VDC, SLEEP > 2.0V, VIN1 = 5VDC
ISET1 = Open, ISET2 = Open
VBRT_ADJ ≤0.5VDC, SLEEP > 2.0V, VIN1 =5VDC
ISET1 = ISET2 = Ground
-20°C < TA < 70°C, VIN1 > 4.75VDC
VBRT_ADJ = 2.5VDC, SLEEP > 2.0V, VIN1 = 5V
Output Burst Frequency
4.4
5
5.6
mARMS
5.4
6
6.6
mARMS
6.4
7
7.6
mARMS
7.4
8
8.6
mARMS
3
10
%
0.30
mARMS
1400
1650
66
70
73
kHz
257
273
286
Hz
Microsemi
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
VRMS
Page 2
ELECTRICALS
Full Bright Lamp Current (each output)
PanelMatch™
I N T E G R A T E D
P R O D U C T S
LXM1623-05-6x
5V Dual 6W Programmable CCFL Inverter Module
P RODUCTION D ATASHEET
Parameter
`
Symbol
IBRT
Input Voltage for Max. Lamp Current
Input Voltage for Min. Lamp Current
`
Units
VBRT_ADJ
VBRT_ADJ
VBRT_ADJ = 0VDC
VBRT_ADJ = 3VDC
IO(LAMP) = Maximum Lamp Current
IO(LAMP) = Minimum Lamp Current
-300
50
2.0
0.5
µADC
µADC
VDC
VDC
0.4
2.05
SLEEP INPUT
RUN Mode
VSLEEP
2.0
VIN1
VDC
SLEEP Mode
VSLEEP
-0.3
0.8
VDC
0.4
V
µA
30
µADC
SET1,2 INPUT
SET1,2 Low Threshold
Input Current
`
LXM1623-05-6x
Min
Typ
Max
BRITE INPUT
Input Current
`
Test Conditions
WWW . Microsemi .C OM
ELECTRICAL CHARACTERISTICS (CONTINUED)
Unless otherwise specified, the following specifications apply over the recommended operating condition and ambient temperature of
25°C except where otherwise noted.
VL
ISET
VSET ≤ 0.4V
-300
POWER CHARACTERISTICS
Sleep Current
IIN(MIN)
Run Current
IIN(RUN)
Efficiency
η
VIN1 = 5VDC, SLEEP < 0.8V
0.0
VIN1 = 5VDC, SLEEP ≥ 2.0V, ISET1 = Open
ISET2 = Ground, VLAMP = 600VRMS
VIN1 = 5VDC, SLEEP ≥ 2.0V, ISET1 = Open
ISET2 = Ground, VLAMP = 600VRMS
4
2100
mADC
80
%
FUNCTIONAL PIN DESCRIPTION
CONN
PIN
DESCRIPTION
CN1 (Molex 53261-0890) Mates with 51021-0800 housing, 50079-8100 pins. Mates with LX9501 input cable assembly
CN1-1
CN1-2
CN1-3
CN1-4
VIN1
Main Input Power Supply (4.75V < VIN1 < 5.25V)
GND
Power Supply Return
CN1-5
SLEEP
ON/OFF Control. (0V < SLEEP < 0.8 = OFF, SLEEP >= 2.0V = ON
CN1-6
BRITE
Brightness Control (0.5V to 2.0VDC). 2.0VDC gives maximum lamp current.
CN1-7
SET1
SET1 MSB Connecting this pin to ground decreases the output current (see Table 1)
CN1-8
SET2
SET2 LSB Connecting this pin to ground decreases the output current (see Table 1)
CN2, CN3 for LXM1623-05-61 and -62 (JST SM02(8.0)B-BHS-1-TB | Yeon Ho 20015WR-05A00 or SM02B-BHSS-1-TB |
35001WR-02A00)
VHI
High voltage connection to high Side of lamp. Connect to lamp terminal with shortest lead length.
DO NOT connect to Ground.
CN2-2
CN3-2
VLO
Connection to low side of lamp. Connect to lamp terminal with longer lead length.
DO NOT connect to Ground
CN2, CN3 for LXM1623-05-63 (Honda QZ-19-A3MYL #02)
CN2-3
CN3-3
VHI
High voltage connection to high side of lamp. Connect to lamp terminal with shortest lead length.
DO NOT connect to Ground.
CN2-1
CN3-1
VLO
Connection to low side of lamp. Connect to lamp terminal with longer lead length.
DO NOT connect to Ground
Copyright © 2002
Rev. 1.0b, 2005-01-17
Microsemi
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 3
ELECTRICALS
CN2-1
CN3-1
PanelMatch™
I N T E G R A T E D
LXM1623-05-6x
5V Dual 6W Programmable CCFL Inverter Module
P R O D U C T S
P RODUCTION D ATASHEET
WWW . Microsemi .C OM
TABLE 1
OUTPUT CURRENT SETTINGS
SET1
(Pin 7)
Open*
Open*
Ground
Ground
SET2
(Pin 8)
Open*
Ground
Open*
Ground
Nominal Output Current
8.0mA
7.0mA
6.0mA
5.0mA
* If driven by a logic signal it should be open collector or open drain only, not a voltage source.
PHYSICAL DIMENSIONS
LXM1623-05-6X
GROUNDED MOUNTING HOLE 3MM ±.08 DIA.
6MM HEAD CLEARANCE BOTH HOLES
165mm
6.496 in.
151mm
5.945 in.
MOUNTING HOLE 3MM ±.08 DIA.
3mm
0.118 in.
CN1
21mm
CN2
CN3
0.827in.
18mm
0.7087 in.
14mm
137mm
1mm
0.551 in.
5.3937 in.
0.0394 in.
7.5mm
Max
Warning
0.295in.
weight: 20g
PCB tolerances ± 0.5mm , 4-40 recommended mounting screws
High Voltage Present at
high side of Transformers
and Output Connectors
Dimensions are in millimeters (inches for reference only)
SIMPLIFIED BLOCK DIAGRAM
+3V
High Voltage
Transform er
V BRIT E
10K
Comparator
+
0.5 2V DC
Ramp
-
Ram p
Gen
V IN1
PACKAGE DATA
+3V
Transform er
Driver
V HI
LAMP
Controller
OC SENSE
10K
SET 1
SET 2
+3V
OV SENSE
10K
I SENSE
V LO
O ne of two
Copyright © 2002
Rev. 1.0b, 2005-01-17
Microsemi
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 4
PanelMatch™
I N T E G R A T E D
P R O D U C T S
LXM1623-05-6x
5V Dual 6W Programmable CCFL Inverter Module
P RODUCTION D ATASHEET
5V
DAC or
Pot
The brightness control may be a voltage output DAC or
other voltage source, a digital pot or 20K manual pot. The
inverter contains an internal 10K pull-up to 3V to bias the
pot, add a 1.8K resistor to set the lower threshold voltage.
A 3.3V Logic Level PWM signal from a micro-controller
may also be used as shown in Figure 1A.
ƒ
If you need to turn the inverter ON/OFF remotely, connect
to TTL logic signal to the SLEEP input.
ƒ
Connect VHI to high voltage wire from the lamp. Connect
VLO to the low voltage wire (wire with thinner insulation).
Never connect VLO to circuit ground as this will defeat
lamp current regulation. If both lamp wires have heavy
high voltage insulation, connect the longest wire to VLO.
This wire is typically white.
ƒ
Use the SET1 and SET2 (see Figure 2) inputs to select the
desired maximum output current. Using these two pins in
combination allows the inverter to match a wide variety of
panels from different manufactures. Generally the best
lamp lifetime correlates with driving the CCFL at the
manufactures nominal current setting. However the SET1
and SET2 inputs allow the user the flexibility to adjust the
current to the maximum allowable output current to
increase panel brightness at the expense of some reduced
lamp life.
ƒ
Although the SET pins are designed such that just leaving
them open or grounding them is all that is needed to set the
output current, they can also be actively set. Using a open
collector or open drain logic signal will allow you to
reduce the lamp current for situations where greater dim
range is required, as an example in nighttime situations. In
conjunction with a light sensor or other timer the panel
could be set to higher brightness (maximum output
current) for daytime illumination and lower brightness
(minimum or typical output current) at nighttime. Since
the dim ratio is a factor of both the burst duty cycle and the
peak output current, using this technique the effective dim
ratio can be increased greater than the burst duty cycle
alone. Conversely the SET inputs could be used to
overdrive the lamp temporarily to facilitate faster lamp
warm up at initial lamp turn on. Of course any possible
degradation on lamp life from such practices is the users
responsibility since not all lamps are designed to be
overdriven.
ƒ
The inverter has a built in fault timeout function. If the
output is open (lamp disconnected or broken) or shorted
the inverter will attempt to strike the lamp for several
seconds. After about 2 to 4 seconds without success the
inverter will shutdown. In order to restart the inverter it is
necessary to toggle the sleep input or cycle the VIN1 input
supply.
V IN1
BRITE
0.45V 20K
to 2.0V
V HI
LXM1623-05-6x
1.8K
SLEEP
SET 1
SET 2
GND
CCFL
TUBE
V LO
ONE OF
TW O
NC
NC
Figure 1 – Brightness Control
(Output current set to maximum)
PW M Signal
from System
BRITE
P.W .
LXM1623-05-6x
10us to 125uS
0 < P.W. < 100% of period
Figure 1A – PWM Brightness Control
5V
V IN1
BRITE
V HI
CCFL
TUBE
LXM1623-05-6x
SLEEP
SET 1
SET 2
GND
V LO
ONE OF
TW O
L
L
H
H
L
5.0mARMS
H
6.0mARMS
L
7.0mARMS
H
8.0mARMS
L=GND; H=Open
Figure 2 – Max Output Current
(SET1 and SET2 Inputs)
Copyright © 2002
Rev. 1.0b, 2005-01-17
Microsemi
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 5
APPLICATION
ƒ
WWW . Microsemi .C OM
TYPICAL APPLICATION
PanelMatch™
I N T E G R A T E D
P R O D U C T S
LXM1623-05-6x
5V Dual 6W Programmable CCFL Inverter Module
P RODUCTION D ATASHEET
NOTES
WWW . Microsemi .C OM
PRODUCTION DATA – Information contained in this document is proprietary to
Microsemi and is current as of publication date. This document may not be modified in
any way without the express written consent of Microsemi. Product processing does not
necessarily include testing of all parameters. Microsemi reserves the right to change the
configuration and performance of the product and to discontinue product at any time.
Copyright © 2002
Rev. 1.0b, 2005-01-17
Microsemi
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 6