+85°C 7mm Height Low-Leakage Radial Lead Aluminum Electrolytic Capacitors PLM For all timing applications FEATURES Very small size Capacitance range: 0.1 µF to 100 µF Voltage range: 6.3 WVDC to 50 WVDC Solvent tolerant end seals standard SPECIFICATIONS Capacitance Tolerance ±20% at 120Hz, 20°C Operating Temperature Range -40°C to +85°C Dissipation Factor 120Hz, 20°C Impedance Ratio (Max.) @120Hz Leakage Current WVDC 6.3 10 16 25 35 50 tan δ .24 .20 .16 .14 .12 .10 WVDC 6.3 10 16 25 35 50 -25/20°C 4 3 2 2 2 2 -40/20°C 10 8 6 4 3 3 WVDC ≤ 50 WVDC Time 2 minutes .002CV or .4µA whichever is greater 1,000 hours at 85°C with rated WVDC Load Life Capacitance change < 20% of initial measured values Dissipation factor Leakage current <200% of initial specified value <Initial specified value 1,000 hours at 85°C with no voltage applied. Units will meet load life specifications. Shelf Life Temperature (°C) Frequency (Hz) Ripple Current Multipliers 50 0.8 120 1.0 SPECIAL ORDER OPTIONS • Special tolerances: ±10% (K), -10% + 30% (Q) • • Epoxy end seal • Polyester sleeve 400 1.3 1K 1.36 10K 100K 1.53 1.48 +85 1.0 +70 1.3 +60 1.5 +45 1.8 (See pages 33 thru 37) Tape and Reel/Ammo Pack • Cut, formed, cut and formed, and snap-in leads ® 3757 W. Touhy Ave., Lincolnwood, IL 60712 • (847) 675-1760 • Fax (847) 673-2850 • www.illcap.com + 85°C 7mm Height Low Leakage Radial Lead Aluminum Electrolytic Capacitors PLM STANDARD PART LISTING Capacitance (µF) PART NUMBER WVDC Maximum ESR Ω 120Hz,+20°C Maximum RMS Ripple Current (mA) 120Hz,+85°C Dimensions DxL (mm) Capacitance (µF) WVDC PART NUMBER Maximum ESR Ω 120Hz,+20°C Maximum RMS Ripple Current (mA) 120Hz,+85°C Dimensions DxL (mm) 0.1 50 104PLM050M 1657.86 1 4x7 10 35 106PLM035M 19.894 34 5x7 0.22 50 224PLM050M 753.57 2 4x7 10 50 106PLM050M 16.579 41 6.3x7 0.33 50 334PLM050M 502.38 3 4x7 22 6.3 226PLM6R3M 18.086 31 4x7 0.47 50 474PLM050M 352.74 5 4x7 22 16 226PLM016M 12.057 43 5x7 1.0 50 105PLM050M 165.79 10 4x7 22 35 226PLM035M 9.043 56 6.3x7 2.2 50 225PLM050M 75.357 17 4x7 33 10 336PLM010M 10.048 48 5x7 3.3 50 335PLM050M 50.238 20 4x7 33 25 336PLM025M 7.033 62 6.3x7 4.7 35 475PLM035M 42.328 22 4x7 47 6.3 476PLM6R3M 8.466 52 5x7 4.7 50 475PLM050M 35.274 27 5x7 47 16 476PLM016M 5.644 69 6.3x7 10 16 106PLM016M 26.526 27 4x7 100 6.3 107PLM6R3M 3.979 82 6.3x7 PHYSICAL DIMENSIONS WVDC (SV) 16 (20) 10 (13) 6.3 (8) (µF) 25 (32) 35 (44) 50 (63) 0.1 4x7 .22 4x7 .33 4x7 .47 4x7 1.0 4x7 2.2 4x7 4x7 3.3 4.7 4x7 10 4x7 22 5x7 47 5x7 100 6.3x7 5x7 5x7 6.3x7 6.3x7 5x7 33 4x7 6.3x7 6.3x7 DxL(mm) Convert to inches, divide by 25.4 LEAD INFORMATION VS. CASE DIAMETER 15.0 MIN PVC SLEEVE d - 4 5 6.3 S 1.5 2.0 2.5 d .45 .45 .45 L1= L+1mm Max. S1= S± 0.5 mm Max. D1= D+ 0.5 mm Max. 19.0 MIN L1 + S1 D D1 ® 3757 W. Touhy Ave., Lincolnwood, IL 60712 • (847) 675-1760 • Fax (847) 673-2850 • www.illcap.com